Home > Nitsuko > Communications System > Nitsuko 124i/384i Software Manual

Nitsuko 124i/384i Software Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Nitsuko 124i/384i Software Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 57 Nitsuko manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    Page
    of 1195
    							Programming
    Start
    Connect the 900i base
    unit LINE IN jack to
    an available DSTU
    station port Refer to the Nitsuko 900i Installation
    and User Guide (P/N 85456DINS**)
    for additional information.
    (Skip this decision for 124i)
    Do you want to set the 900i
    port programming manually
    or automatically?Run 0004. The
    system sets the 900i
    circuit type to 1.Auto-
    maticallyIn 0005, enter
    circuit type 1 for
    each 900i port.Manually
    Should the 900i
    have a companion
    keyset?
    Should the 900i have a
    key appearance for all
    incoming trunk calls?In 1006, leave the
    programmable keys at
    their default setting (i.e.,
    as line keys 1-4).In 1006, assign a both
    ways loop key (code
    1078 + 2) to one of the
    900i programmable keys.
    YesNo
    Stop
    Continued
    on next
    page.
    No
    Connect the 900i base
    unit LINE OUT jack to
    the companion keyset.
    Yes
    Features B-D
    Cordless Telephone (Nitsuko 900i)
    92000SWG08   Issue 1-0FEATURES   191 
    						
    							Programming (Cont’d)
    In 1006, assign a Call
    Coverage Key (1036 + ext.) on
    the 900i for the companion
    keyset and visa versa.
    Should user be able to
    use the desk button
    on the 900i base to
    Transfer calls to the
    companion keyset?In 1009, assign the 900i
    port as the Boss STA
    PORT and enter the
    companion keyset port
    as the 
    STA_nn data.
    Do not make any
    entries in 1009.
    Stop
    YesNo
    Continued
    from
    previous
    page.
    Should the Call
    Coverage keys ring or
    just flash?In 1016, enable (1)
    ringing for the selected
    extension and function
    key for each Night
    Service mode.
    Ring
    In 1016, disable (0)
    ringing for the selected
    extension and function
    key for each Night
    Service mode.
    Flash
    For calls ringing the
    Call Coverage keys,
    should the ringing be
    immediate or delayed?In 1028, enter 1 for
    delayed ringing.DelayedIn 1028, enter 0
    for immediate
    ringing.Immediate
    In 0414 Item 5, adjust
    the Call Coverage
    Delay Interval if
    required.
    Do you want to
    change the way
    calls ring Call
    Coverage  keys?In 1018, assign a ring
    tone range for each
    extension port assigned
    to a Call Coverage key.
    Yes
    When an extension
    has more than one Call
    Coverage key, do you
    want to change the
    ringing priority?
    No
    In 1019, reassign the
    Call Coverage key
    ring tone priorities.Yes
    No
    Features B-D
    Cordless Telephone (Nitsuko 900i)
    192   FEATURES92000SWG08   Issue 1-0 
    						
    							Programming (Cont’d)
    ➣
    (384i Only) 0004 - Automatic Extension Circuit Type Setup
    Use this program to automatically set up the Nitsuko 900i station port. When you run Program 0004, the
    system automatically assigns circuit type 1 to all the Nitsuko 900i ports.
    ➣(384i Only) 0005 - Manual Extension Circuit Type Setup
    If you don’t want to use Program 0004, use this program instead. Use the Type option to set the circuit
    type of the Nitsuko 900i station port to circuit type 1. Refer to Understanding Port Assignments on
    page 626 for more explanation.
    ➣0414 - System Timers (Part B), Item 5: Call Coverage Delay Interval
    Multiple Directory Number/call Coverage Keys set for Delayed Ringing (see Program 1028 below) ring
    the covering extension after this interval.
    ➣1006 - Programming Function Keys
    •Assign a Loop Key (code 1078 + option) to the Nitsuko 900i to make placing and answering out-
    side calls easier. For example, code 1078 + 2 will provide a both ways loop key. The user can
    press the key to place a call on the dial 9 Trunk Group. In addition, the key provides an appear-
    ance for any incoming call that is not specifically assigned to one of the Nitsuko 900i line keys.
    •Assign a Call Coverage Key (code 1036 + covered) to both the Nitsuko 900i and the companion
    keyset. The Nitsuko 900i should cover the companion and visa versa. This gives the Nitsuko 900i
    and the companion keyset on-button access to each others calls.
    ➣1009 - Cordless/Desktop Extension Assignment
    Make entries into this program if you want to enable the DESK button on the Nitsuko 900i base unit. For
    the Boss STA PORT? prompt, enter the Nitsuko 900i port number. For the STA_nn prompt, enter the com-
    panion desk set’s port number.
    ➣1016 - Setting Ringing for Multiple Directory Numbers
    Individually program the Nitsuko 900i and companion keyset Call Coverage keys to either ring (1) or not
    ring (0).
    ➣1018 - Multiple Directory Number Ring Tone Range
    Use this program to assign a unique ring tone range (0-4) to each port assigned to a Call Coverage key.
    This is important if the Nitsuko 900i and/or companion keyset have more than one Call Coverage key.
    The unique ring tone helps the user quickly determine which key is ringing.
    ➣1019 - Multiple Directory Number Ring Tone Priority
    Use this program to set the priority (1-4) for the tones assigned in Program 1018 above. You make one as-
    signment for each port. When multiple Call Coverage key calls ring an extension simultaneously, the
    tone with the highest priority (e.g., 1) rings. The other keys just flash.
    ➣1028 - Multiple Directory Number Key Delayed Ringing
    Individually program an extension’s Call Coverage keys for Delayed Ringing (1) or Immediate ringing
    (0). Also see Program 0414 Item 5 above.
    Related Features
    Refer to the Nitsuko 900i Cordless Phone Installation and User Guide (P/N 85456DINS**) for Related Feature
    information. 
    Operation
    Refer to the Nitsuko 900i Cordless Phone Installation and User Guide (P/N 85456DINS**) for the specifics on
    feature operation.
    Features B-D
    Cordless Telephone (Nitsuko 900i)
    92000SWG08   Issue 1-0FEATURES   193 
    						
    							Data Communications Interface (DCI)
    Description
     124i Available — 72 DCI software ports,
    allocated between 72 DCI Modules
    and six 3-DCI Units (two per
    cabinet) maximum. 384i Available — 288 DCI software ports,
    with 144 DCI Modules and 48 3-
    DCI Units maximum. System
    software prior to 3.04 uses different
    DCI Types. System software 3.05
    and higher has default assignments
    for the first 3-DCI installed.
    With the Data Communications Interface (DCI), you can use your telephone system to set up a data network.
    DCI networking lets system users share common office resources such as PCs, modems and printers.  Since the
    phone system handles the network communications, you can eliminate the expense of separate wiring, network
    adapters and network driver software.  The DCIs can switch asynchronous RS-232-C data at speeds from 300 to
    19.2K baud.  Internal X.25 packet switching ensures maximum data reliability with a minimum of disruption to
    other system activities.  
    There are three types of DCIs:
    •RS-232-C DCI Module (DCI-A: P/N 92266)
    The DCI-A is a single port data module that installs in a multibutton phone for serial (RS-232-C) 
    communications. Although it installs in the phone, the DCI-A has its own unique port and extension num-
    ber.  Use DCI-A to easily add RS-232-C data capabilities to any keyset.  The 384i system can have up to
    144 DCI Modules; the 124i up to 72 (DCI-A plus DCI-B - see below).
    •Centronics DCI Module (DCI-B: P/N 92267)
    The DCI-B is also a single port data module that installs in a multibutton telephone, but it is used for
    parallel (Centronics) communication.  Like the DCI-A, DCI-B also has its own unique port and exten-
    sion number.  Use the DCI-B to connect a parallel printer to your data network. The DCI-B operates in
    one direction only. A switch on the DCI-B lets you send data OUT (from DCI-B to printer) or IN (from
    printer to DCI-B). The 384i system can have up to 144 DCI Modules,; the 124i up to 72 (DCI-A plus
    DCI-B - see above). The DCI-B requires a unique cable — consult with your sales representative.
    •3-Port DCI Unit (3DCI-A: P/N 92258)
    The 3DCI-A is a stand-alone unit that connects to a single DSTU PCB port and provides three RS-232-C
    ports.  The 3DCI units are helpful in areas that have a high concentration of data devices. Since you can have
    three devices connected to each 3DCI, you use up 1/3 the number of DTSU PCB ports (when compared to the
    DCI Module).  Keep in mind, however, that 3DCI Units do not have an associated telephone.  The 384i sys-
    tem can have up to 48 3DCI Units (144 data ports); the 124i up to three (six data ports).
    DCI Features
    •Keyset-Originated Data Call
    Place a call to another DCI by using your telephone dial pad. The data call automatically sets up if the
    called DCI answers.
    •Terminal-Originated Data Call
    Place data calls directly from your PC.  You can dial using Hayes compatible dialing commands (e.g.,
    ATDT) or use the powerful auto-dialing features of your communications software.
    •Terminal-Originated Voice Call (Telemarketing Dial)
    Use your PC to place an outgoing call, then switch to a voice call after the number dials out.  This is a
    great feature for telemarketers that have a list of names to call stored in their communications software.
    Let the communications software dial the call - then switch it to a voice call after the stored number dials
    out. Each phone with Telemarketing Dial should have a Telemarketing Dial key (code 1045). See Pro-
    gramming for more.
    Features B-D
    Data Communications Interface (DCI)
    194   FEATURES92000SWG08   Issue 1-0 
    						
    							Description (Cont’d)
    •DCI Department Group
    Group DCIs into departments for pooled DCI operation.  For example, you can program several network
    printers into a DCI Department Group (see the illustration below).  When a user calls the department,
    they connect to the first available printer.  
    DCI Department Groups also allow modem pooling for trunk calls without using a proprietary Modem
    Pooling PCB (see the illustration below).  Users placing outside calls select one of the pooled modems as
    part of the dialing sequence.  Refer to the Hardware Manual for additional installation details.
    3DCI
    3DCI PC 16DSTU
    ASTUSerial PrinterModem
    Modem Modem
    Modem
    920 - 168 f
    (384i System Shown)
    Features B-D
    Data Communications Interface (DCI)
    92000SWG08   Issue 1-0FEATURES   195 
    						
    							Description (Cont’d)
    •Hayes Compatibility
    The DCI is compatible with many Hayes AT commands.  For example, you can use S-registers to change
    DCI communications parameters (refer to Table DCI-2).  In addition, Result Codes help you monitor the
    progress of your call (refer to Table DCI-4).  You can also enter over 20 Hayes commands  from your ter-
    minal to control dialing and terminal options, Result Code display and S-register 
    programming (refer to Table DCI-5).
    •DCI Hotline
    DCI Hotline sets up a nailed-up (permanent) connection between a DCI Module and another DCI.
    During programming, you set the DCI Module as the source and the other DCI as the target. When
    the user at the source presses the keyset data key, the system automatically sets up the data link to the tar-
    get DCI. You could use a DCI Hotline at a terminal connected through the phone system to a mini-com-
    puter.  When the terminal user presses the keyset Hotline key, the terminal goes on-line to the
    mini-computer.
    •Speed Conversion
    The system can automatically compensate for speed differences between two connected data devices.
    For example, a PC receiving at 2400 baud can accept files sent by another PC at 19.2K baud. There is no
    need for the two devices to match their communications speed
    Physical Ports and Software Ports
    DCIs have physical ports and corresponding software ports.  The software ports are used during system program-
    ming.  For DCI Modules, the physical port is the same as the phone port into which the module is installed.  In 384i,
    the software port (1-144) depends on the installation order (set in Program 0005).  Order 1 specifies software port 1;
    order 144 specifies software port 144.  Normally you’ll assign DCI Order 1 to the first DCI Module you install and
    Order 144 to the last. In 124i, the software port is the same as host telephone’s physical port. The total of all 124i data
    device software ports cannot exceed 72.
    Each 3DCI consists of a physical port for connection to the phone system and three software ports.  The physical
    port is the station port into which the 3DCI line cord is plugged.  In 384i, the 3DCIs have a different software
    port numbering scheme which is also determined by the installation order set in Program 0005.  The 3DCI with
    order 1 (shown below) has software ports 145, 146 and 147.  The 3DCI with order 48 (the highest 3DCI order
    number available) has software ports 286, 287 and 288.  Normally, you assign 3DCI Order 1 to the first 3DCI
    you install and Order 48 to the last. In 124i, the software port is the same as the extension port to which the mod-
    ule is connected and the next two consecutive ports. The total of all 124i data device software ports cannot ex-
    ceed 72.
    384i Data Communications Interface Devices
    Device Total Number of
    Physical PortsInstallation Order
    Numbers Software  Ports
    DCI Modules  144 (in phone) 1-144  1-144 
    3DCI Units  48  1-48  145-288 
    Features B-D
    Data Communications Interface (DCI)
    196   FEATURES92000SWG08   Issue 1-0 
    						
    							Description (Cont’d)
    During programming, you assign DCI extension numbers, Department Group options and Tenant Group options
    to DCI software ports, not physical ports.  During installation, the equipment plugged into the connectors
    correspond to the DCI software ports.  Refer to the system Hardware Manual for more installation details.
    Conditions
    None
    Default Setting
    •Disabled.
     
    Software
    Port 147Software
    Port 146Software
    Port 145
    Physical
    Port (Order 1)
    PORT 1 PORT 2 PORT 3
    LINEFG
    920 - 166A
    To DSTU
    PCB Port
    (384i System Shown)
    Features B-D
    Data Communications Interface (DCI)
    92000SWG08   Issue 1-0FEATURES   197 
    						
    							Description (Cont’d)
    DCI S-Registers (Register Type 1)
    Register Description Range Default
    0Number of Rings Until Auto-Answer
    The number of rings required before the DCI port
    answers the call. 0 (No auto-answer)
    1-255 (2-510 seconds)0
    1Ring Count
    The register that stores the number or rings
    detected by the DCI0-255 (0-510 seconds) 0
    2Escape Character 
    The decimal value of the ASCII character used for
    Escape0-127 (decimal) 43
    3Carriage Return Character
    The decimal value of the ASCII character used for
    carriage return0-127 (decimal) 13
    4Line Feed Character
    The decimal value of the ASCII character used for
    line feed.0-127 (decimal) 10
    5Backspace Character
    The decimal value of the ASCII character used as
    a backspace.0-32, 127 (decimal) 8
    7Wait for Carrier After Dial
    During call setup, sets time DCI waits for carrier
    from remote modem before hanging up. Also Sets
    time DCI pauses when it encounters a W in the
    dial string.1-255 (seconds) 30
    9Carrier Detect Response Time
    Minimum duration of valid carrier signal.1-255 (10-2550 mS) 6 (60 mS)
    10Lost Carrier to Hang Up Delay
    Length of time DCI waits before hanging up after
    loss of carrier (must be greater than register 9)1-255 (10-2550 mS) 14 (140 mS) 
    12Escape Code Guard Time
    Delay (guard) time before and after entering
    escape character.0, 1-255 
    (0, 20-5100 mS)50 (1 second)
    25Delay to DTR
    In synchronous mode, sets interval between
    connection and examination of DTR. Also
    After connection, sets minimum duration of
    valid DTR signal.1-255 (10-1550 mS) 5 (50mS)
    Features B-D
    Data Communications Interface (DCI)
    198   FEATURES92000SWG08   Issue 1-0 
    						
    							DCI S-Registers (Register Type 1)
    Register Description Range Default
    58DTE/DCE Terminal Type
    You can configure a DCI-A Module (P/N 92266)
    as either a DCE of DTE device. Use the DCE (1)
    configuration if you have a straight-thru cable and
    you want to connect directly to a terminal or PC
    serial port.  Use the DTE (0) configuration if you
    have a straight-thru cable and you want to connect
    directly to a modem. (This option requires system
    software 3.04. Prior to 3.04, this options was
    Register 59, Data Watchdog Timer.)0 = DTE
    1 = DCE0 (DTE)
    59Data Watchdog Timer (Low)
    If a data low condition exists for longer than this
    interval, the system disconnects the data call. This
    option is only available in system software prior
    to 3.04.1-255 seconds
    0=disabled0 (disabled)
    60Data Watchdog Timer (High)
    If a data high condition exists for longer than this
    interval, the system disconnects the data call. This
    option is only available in system software prior
    to 3.04.1-255 seconds
    0 = disabled0 (disabled)
    61Packet Size
    Sets the size of the data packet. Packets exceeding
    this size are transmitted. Packets less than this size
    are not (unless timeout occurs - see register 63). 0-255 (0-255 byte) 255
    62Te r m i n a t e  C o d e
    The decimal value of the ASCII code used to end
    (terminate) a command line.0-127 (decimal) 13 (CR)
    63Data Transmission Time
    Sets how long DCI waits before transmitting an
    incomplete packet. Use register 61 to set packet
    size.0, 1-255 
    (0, 50-12750 mS)
    0=disabled5 (250 mS)
    64Result Code Send/Block
    Allows/prevents sending of Result Codes to
    device connected to DCI.0=Send 
    1=Do Not Send 0 (Send)
    Result Code Type
    Enables sending of Result Codes as words or
    numbers.0=Numeric 
    1=Words1 (Words)
    Result Code Mode
    Determines which set of Result Codes are sent to
    device connected to DCI (Basic or Extended - see
    Table with DCI feature).0=Basic 
    1=Extended0 (Basic)
    Features B-D
    Data Communications Interface (DCI)
    92000SWG08   Issue 1-0FEATURES   199 
    						
    							DCI S-Registers (Register Type 1)
    Register Description Range Default
    65Baud Rate
    Sets the baud rate of the DCI port.1=300 BPS 
    2=600 BPS 
    3=1200 BPS 
    4=2400 BPS
     5=4800 BPS 
    6=9600 BPS 
    7=19,200 BPS6 (9600 BPS)
    Stop Bit 
    Sets the number of stop bits the DCI expects in the
    data stream 0=1 stop bit 
    1=2 stop bits0 (1 stop bit)
    Data Bits
    Sets the number of data bits the DCI expects in the
    data stream.0=7 data bits 
    1=8 data bits1 (8 data bits)
    Parity
    Sets the parity method the DCI expects in the data
    stream 0=No parity
    1=Not used 
    2=Odd parity 
    3=Even parity0 (no parity)
    66Request to Send (RTS) Control
    Enables (0) or disables (1) RTS (pin 4) control. If
    disabled, the DCI holds RTS on.0=Control enabled
    1=Disabled (normally
    on)0 (control
    enabled)
    Data Terminal Ready (DTR) Control 
    Enables (0) or disables (1) DTR (pin 20) control.
    If disabled, the DCI holds DTR on.0=Control enabled
    1=Disabled (normally
    on)0 (control
    enabled)
    Clear to Send (CD Control)
    Enables (0) or disables (1) CTS (pin 5) control. If
    disabled, CTS follows RTS (pin 4). 0=Control enabled
    1=Disabled (follows
    RT S )0 (control
    enabled)
    Flow Control
    Sets flow control.0=No flow control
    1=RTS/CTS
    (hardware) flow
    control enabled
    2=XON/XOFF
    between DCI and
    connected terminal
    3=XON/XOFF
    between sender and
    receiver (DCI
    transparent)1 (hardware
    flow control)
    Features B-D
    Data Communications Interface (DCI)
    200   FEATURES92000SWG08   Issue 1-0 
    						
    All Nitsuko manuals Comments (0)

    Related Manuals for Nitsuko 124i/384i Software Manual