NEC Neax 2400 Ipx Office Data Specification
Have a look at the manual NEC Neax 2400 Ipx Office Data Specification online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1168 NEC manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
NDA-24298 CHAPTER 4 Page 917 Issue 1 ASYDN : Assignment of System Data in Network Data Memory 1162-169 Not used 170b 0~b3Not used b 4 Timing Start 0/1 = Not Required/Required b 5~b7Not used 171-303 Not used 304b 0 Individual Speed Calling Data Save 0/1 = Out/In Service (This data is valid when SYS1, INDEX 90, b 1 = 1) b1 Call Forwarding Data Save 0/1 = Out/In Service (This data is valid when SYS1, INDEX 90, b 1 = 1) b2Not used b 3 Name Display Data Save 0/1 = Out/In Service (This data is valid when SYS1, INDEX 90, b 1 = 1) b4 Not used b5 b6 b7 305 00Not used 320 00Not used 3210b 0Not used 0b 1 b2 Termination on My Line 0/1 = Not Restricted/Restricted 0b 3 Not used 0b4 0b5 0b6 b7 Voice Call Chime 0/1 = 4/1 Chime SYSTEM DATA TYPE (SYS)SYSTEM DATA INDEX (INDEX) 0 – 1535DATA (DATA) 00 – FF (Hex)BIT CORRESPONDING DATA SYSTEM DATA CONTENTS (MDATA) DATA 0/ 1 BIT ~~~
CHAPTER 4 NDA-24298 Page 918 Issue 1 ASYDN : Assignment of System Data in Network Data Memory 1322 00 Not used 511 00Not used 512 00 Not used 513 00 Not used 514 01b 0Local Data Memory (LDM) usage. Assign data “1” (the memory block is used) for the corresponding memory block. Note: Necessary data for the programming commands for NDM. When the Network Data Memory is not enough, change the value from 03H → 07H → 0FH → 1FH. Usually 01H is assigned. b1 b2 b3 b4 b5 b6 b7 515-532 Not used 533FPC that accommodates center VND (1~253) Note:Assign the FPC of ACDP accommodated node. 534-582 Not used. 583b 0~b6Not used. b 7 Node that collects the billing of SMDR activated in a Fusion network. 0 = the node accommodating the calling party 1 = the node accommodating the outgoing trunk or the node accommodating the called party 584-799 Not used. SYSTEM DATA TYPE (SYS)SYSTEM DATA INDEX (INDEX) 0 – 1535DATA (DATA) 00 – FF (Hex)BIT CORRESPONDING DATA SYSTEM DATA CONTENTS (MDATA) DATA 0/ 1 BIT ~~~ bit Memory Block b 0Memory Block #0 b1Memory Block #1 b2Memory Block #2 b3Memory Block #3 b4Memory Block #4
NDA-24298 CHAPTER 4 Page 919 Issue 1 ASYDN : Assignment of System Data in Network Data Memory 18000b 0 ALGNN/ALGSN command tenant UGN (User Group Num- ber) table development of Network Data Memory (NDM) 0/1 = Separate/Common b 1 ASPAN command tenant table development of Network Data Memory (NDM) 0/1 = Separate/Common b 2 ANPDN command tenant table development of Network Data Memory (NDM) 0/1 = Separate/Common b 3 APCNN command tenant data table development of Network Data Memory (NDM) 0/1 = Separate/Common b 4 AFRSN, ASTPN command tenant table development of Net- work Data Memory (NDM) 0/1 = Separate/Common b 5 ASTPN command tenant data table development of Network Data Memory (NDM) 0/1 = Separate/Common b 6 ARSCN command tenant data table development of Network Data Memory (NDM) 0/1 = Separate/Common b 7 AAEDN command tenant data table development of Network Data Memory (NDM) 0/1 = Separate/Common 801-803 Not used Example: When a call terminates on a Dterm from station number 5000/Telephone number 123456789, the Dterm displays as follows depending on the data settings. SYSTEM DATA TYPE (SYS)SYSTEM DATA INDEX (INDEX) 0 – 1535DATA (DATA) 00 – FF (Hex)BIT CORRESPONDING DATA SYSTEM DATA CONTENTS (MDATA) DATA 0/ 1 BIT ASYDN SYS1, INDEX641, bit0=1 ASYDN SYS1, INDEX672, bit0=0 ASYDN SYS1, INDEX672, bit0=1 8 digits long maximum when telephone number is displayed on top line.123456789 11:20 AM WED 16 APR 97 MIC DND >>> 123456789 MIC DND >>>
CHAPTER 4 NDA-24298 Page 920 Issue 1 ASYDN : Assignment of System Data in Network Data Memory Example: When a call terminates on a Dterm from station number 5000/Telephone number 123456789, the Dterm displays as follows depending on the data settings: 18040b 0~b2Not used. b 3The number of digit for Internal Zone Paging group ID 0/1 = 2 digits/3 digits b 4~b7Not used. 805-863 Not used. 8640b 0~b2Not used. b 3Multiple ACDP 0/1 = Out of service/In service 0b 4~b7Not used. 865-869 Not used. 870b 0FLF Fusion Service 0/1 = Invalid/Valid 0b 1~b7Not used. 871-1535 Not used. SYSTEM DATA TYPE (SYS)SYSTEM DATA INDEX (INDEX) 0 – 1535DATA (DATA) 00 – FF (Hex)BIT CORRESPONDING DATA SYSTEM DATA CONTENTS (MDATA) DATA 0/ 1 BIT ASYDN SYS1, INDEX641, bit0=1 ASYDN SYS1, INDEX672, bit0=0 ASYDN SYS1, INDEX672, bit0=1 8 digits long maximum when telephone number is displayed on top line.123456789 11:20 AM WED 16 APR 97 MIC DND >>> 123456789 MIC DND >>>
NDA-24298 CHAPTER 4 Page 921 Issue 1 AFMU : Assignment of FPC, MG and UNIT for Network Data Memory AFMU: Assignment of FPC, MG and UNIT for Network Data Memory 1. General This command allocates the Network ID (NID) that is the unique location number in the Fusion Network. 2. Precautions 1. NID allocation is required for the Fusion network only. 2. For detailed information, see the NEAX2400 IPX Fusion Network System Manual. 3. Data Entry Instructions FUSION POINT CODE (FPC) 1-253UNIT NUMBER (U) 0-3MODULE GROUP NUMBER (MG) 0-7 U Assign Unit No. of the node respectively. FPC FPC is the unique number allocated to each node. Assign FPC of all nodes in the Fusion network.MG Assign MG No. of the node respectively.
CHAPTER 4 NDA-24298 Page 922 Issue 1 AFMU : Assignment of FPC, MG and UNIT for Network Data Memory 4. Data Sheet FUSION POINT CODE (FPC) 1-253MODULE GROUP NUMBER (MG) 0-7UNIT NUMBER (U) 0-3REMARKS
NDA-24298 CHAPTER 4 Page 923 Issue 1 ALRTN : Assignment of Logical Route for Network Data Memory ALRTN: Assignment of Logical Route for Network Data Memory 1. General This command allocates the Logical Route Number that is the unique number of the external trunk route in the Fusion network. 2. Precautions 1. Logical Route Number allocation is required for the Fusion network only. 2. When assigning the data by this command, the Route Class Data (ARTD) and Trunk Application Data (ARTI) for Physical Route are also allocated to Logical Route Data (ARTDN/ARTIN) on the same condition. 3. For detailed information, see the NEAX2400 IPX Fusion Network System Manual. 3. Data Entry Instructions NUMBER (LGRT) LOGICAL ROUTE FUSION POINT CODE (FPC) 1-253EXTERNAL ROUTE NUMBER (RT) 1-255REMARKS1-899 Assign all external routes including dummy routes in the Fusion network.RT FPC Assign FPC of each node to which the external trunk route belongs.LGRT LGRT is the unique number allocated to each external trunk route in the Fusion network.
CHAPTER 4 NDA-24298 Page 924 Issue 1 ALRTN : Assignment of Logical Route for Network Data Memory 4. Data Sheet LOGICAL ROUTE NUMBER (LGRT) 1-899FUSION POINT CODE (FPC) 1-253EXTERNAL ROUTE NUMBER (RT) 1-255REMARKS
NDA-24298 CHAPTER 4 Page 925 Issue 1 ANPDN : Assignment of Numbering Plan Data for Network Data Memory ANPDN: Assignment of Numbering Plan Data for Network Data Memory 1. General This command assigns the minimum number of digits needed to determine the service (Telephone Number) that is required by the first digit received (pre-translation). The data assigned with this command is written in the Network Data Memory (NDM) of the Network Control Node (NCN), updating the NDM at each Local Node (LN). 2. Precautions 1. This command is used for the Business Application. 2. The applicable Tenant Number (TN) range is designated by the ASYDN command, SYS 1, INDEX 8. If the numbering plan is common for all tenants (ASYDN, SYS1, INDEX 800, bit2=1), assign TN parameter as “1” for all tenants. 3. The system data assignment (ASYDN, SYS 1, INDEX 514, bit1=1) is needed to provide the Network Data Memory (NDM). 4. For detailed information, see the NEAX2400 IPX Fusion Network System Manual. 3. Data Entry Instructions TENANT NUMBER (TN)1st DIGIT CODE (1st DC)CONNECTION STATUS INDEX (CI) N/H/BNUMBER OF NECESSARY DIGITS (NND) MAXIMUM 6 DIGITSBUSY LAMP FIELD DISPLAY ACTIVATED ON A ATT (BLF) 0/1 0 NNDThe first digits analyzed, prior to the ASPAN command to assign a different number of digits for this, assign the minimum number of digits in this parame- ter.1st DC The first digit of access code for Telephone Number. (0-9,*, #) CI The status of the 1st DC dialed N = Normal (Idle) H = Hooking B = BusyBLFNot used (Fixed to 0)
CHAPTER 4 NDA-24298 Page 926 Issue 1 ANPDN : Assignment of Numbering Plan Data for Network Data Memory 4. Data Sheet TENANT NUMBER (TN)1st DIGIT (1st DC)CONNECTION STATUS INDEX (CI) N/H/BNUMBER OF NECESSARY DIGITS (NND)BUSY LAMP FIELD REMARKS 1NNormal H Hooking BBusy 2NNormal H Hooking BBusy 3NNormal H Hooking BBusy 4NNormal H Hooking BBusy 5NNormal H Hooking BBusy 6NNormal H Hooking BBusy 7NNormal H Hooking BBusy 8NNormal H Hooking BBusy 9NNormal H Hooking BBusy 0NNormal H Hooking BBusy *NNormal H Hooking BBusy #NNormal H Hooking BBusy