Home > NEC > Communications System > NEC Neax 2400 Ipx Office Data Specification

NEC Neax 2400 Ipx Office Data Specification

Add to Favourites
    Download as PDF Print this page Share this page

    Have a look at the manual NEC Neax 2400 Ipx Office Data Specification online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1168 NEC manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    View all the pages
    Page
    of 1020
    Add page 681 to Favourites
    image text
    Enable zoom 
    							NDA-24298 CHAPTER 4
Page 647
Issue 1
ARTI : Assignment of Trunk Application Data
6 T309CONAssignment of Timer T309 for Layer 1 Failure
0 = Layer 1 Alarm with T309 is disabled 
1 = Layer 1 Alarm [Temporary] with T309 is enabled
2 = Layer 1 Alarm [Permanent] with T309 is enabled 
3=Not used
7LLCRSTCall Restriction by user rate in Low Layer Capability 
Information Element 
     0= No restriction
1-31= Call which includes this user rate value is 
restricted. 
Note:User rate value is based on ITU-T Q-931. 
8VCM  When assigning this data, always enter zero (0). 0000
9OVRT  When assigning this data, always enter zero (0). 0000
10POOLWhen assigning this data, always enter zero (0). 0000
11 DTRTDeletion of ALL 1 alarm signal (DTI Layer 1 alarm) 
0=Not used
1 = Deletion of ALL 1 alarm signal as a Layer 1 alarm 
12 TMPRTTemporary Route Information over CCIS 
0 = Not used 
1 = In CCIS, the route information can be transferred by 
the call control messages. Moreover, the call 
restriction can be checked referring to this route 
information. 
13CODEC  When assigning this data, always enter zero (0). 0000
14PASSWhen assigning this data, always enter zero (0).  0000
15 IRL Clear call when DTI alarm is detected
0 = Not used
1 = Clear call when DTI alarm is detectedNote 
Note:
This data should be set when there is no 
Dch in the physical DTI. 
16 MTCAssignment of Timer T309 Value.
Restoration timer (TC×MTC) sec.
0-15 = TC×MTC (Restart timer value)
17 TCTimer T309 Counter Value
0 = Not used   1 = 64 msec. 
2 = Not used   3 = 2 sec.
4 = 30 sec.   5 = 5 min.
6 = 1 sec.   7 = Not used 
18TS  When assigning this data, always enter zero (0). 0000
19CDCSPDWhen assigning this data, always enter zero (0). 0000 CDN ROUTE NUMBER
TRUNK DATA
    Add page 682 to Favourites
    image text
    Enable zoom 
    							CHAPTER 4 NDA-24298
Page 648
Issue 1
ARTI : Assignment of Trunk Application Data
20 DVRSTCall restriction while Tie Line is backed up on ISDN. 
0= No restriction
1 = Speech call restriction (Speech. 3.1 kHz audio, 7 
kHz audio calls are restricted)
2 = Data call restriction (Unrestricted digital, restricted 
digital and Video data are restricted.) 
3 = Both Speech and Data calls are restricted. 
21 RSCTCall restricted by Temporary Route Information 
0 = No restriction 1 = Restriction
Note: This data is effective when TMPRT = 1. 
22 ROCGOutgoing Call Account by Temporary Route Information 
0 = Not used 1 = Effective 
Note:This data is effective when TMPRT = 1. 
2 3 RICGIncoming Call Account by Temporary Route Information 
0 = Not used 1 = Effective
Note:This data is effective when TMPRT = 1. 
24 STSENQStatus Inquiry Message Send 
0 = Out of service
1 = In service
25MMNPASSWhen assigning this data, always enter zero (0).  0000
26 DLTK  (Japan only)
When assigning this data, always enter zero (0).0000
27 CALN (Japan only)
When assigning this data, always enter zero (0). 0000
2 8 NETINT (Japan only)
When assigning this data, always enter zero (0).0000
2 9 INBAND  W hen  ass ign in g  t his  data,  alway s en ter  zero  (0 ) .0000
30 RETMSG(Australia only) 
Return Massage for Connect ISDN LINE with Analog 
Trunk
0 = CALL PROC. + ALERT
1 = CALL PROC. + ALERT or CALL PROC. + 
PROGRESS
3 1 ANITiming to demand ANI Information 
0 = There is no ANI demand at Incoming call
1 = After receiving 1st digit
2 = After receiving 2nd digit 
3 = After receiving 3rd digit 
4 = After receiving 4th digit 
5 = After receiving 5th digit
6 = After receiving 6th digit 
7 = After receiving 7th digit CDN ROUTE NUMBER
TRUNK DATA
    Add page 683 to Favourites
    image text
    Enable zoom 
    							NDA-24298 CHAPTER 4
Page 649
Issue 1
ARTI : Assignment of Trunk Application Data
32 SRV (Australia only)
Additional Service Selection 
bit 0 = Advice of Charge (AOC) 
0 = Valid 1 = Invalid
bit 1= Malicious Call Trace (MCT)/Malicious Call Iden-
tification (MCID) 
0 = Valid 1 = Invalid
bit2-bit6 = Not used 
bit7 = For TON and/or NPI
0 = Invalid 1 = Valid 
Note:Input this data by a decimal. 
33 TONType of Number 
0 = Unknown
1 = International Number 
2 = National Number 
3 = Network Special Number
4 = Subscriber Number 5 = Not used
6 = Abbreviated Number 
7 = Reserved for Extension
Note:This data is effective when ARTD, INT = 4 and
SRV bit7 = 1 is assigned. 
34 NPINumbering Plan Identification
0 = Unknown        
1 = ISDN/Telephony Numbering Plan
2=Not used 
3 = Data Numbering Plan 
4 = Telex Numbering Plan 
    5-7 = Not used      
8 = National Standard Numbering Plan
9 = Private Numbering Plan 
 10-14 = Not used 
15 = Reserved for Extension 
Others = Not used
Note:This data is effective when ARTD, INT = 4 and
SRV bit7 = 1 is assigned.
35 L/TLocal/Toll (Russia only)
When assigning this data, always enter zero (0).0000
36 ECCISEvent Based CCIS (E-CCIS)
0 = Out of Service
1=In Service CDN ROUTE NUMBER
TRUNK DATA
    Add page 684 to Favourites
    image text
    Enable zoom 
    							CHAPTER 4 NDA-24298
Page 650
Issue 1
ARTI : Assignment of Trunk Application Data
37 ECCISTMRelease timer for E-CCIS Line 
0 = 3 minutes (Default setting)
1 = 15 Seconds
2 = 30 Seconds
3=1 minute
4=2 minutes
5=5 minutes
6 = 10 minutes
7 = 30 minutes
8 = 30 minutes
9 = 1 hour
10-13 = Not used
14 = Immediately after call completion
15 = Not released
38 ECCISOBOG Billing for E-CCIS Line
0 = Out of Service
1=In Service
39 ECCISIBIC Billing for E-CCIS Line 
0 = Out of Service
1=In Service
4 0 SPMETAccount Pulse Watch Control
Not used 
41 IDRTID Code Specification
Not used
42 ECCISTDAddressing Information used in E-CCIS
0 = Called DID Number
1 = Called Sub Address
43 MFCG2MFC Outgoing Call GII
0 = Priority
1 = Non Priority
44 OPCCOptimal Call Control
0=In Service
1 = Out of Service
45 ICTCONICT Control
0 = Send ALERT
1 = Send CONN
When assigning this data, always enter zero (0).0000
46 VRDVoice Recognize Dial
When assigning this data, always enter zero (0).0000
47 INTDInterface Detail
0=Q-SIG
1 = IS-11572
4 8 JECCISCommon Use with E-CCIS RT
0 = Out of Service
1=In Service CDN ROUTE NUMBER
TRUNK DATA
    Add page 685 to Favourites
    image text
    Enable zoom 
    							NDA-24298 CHAPTER 4
Page 651
Issue 1
ARTI : Assignment of Trunk Application Data
49 ECCIS2E-CCIS System
0 = Out of Service
1 = Common Channel System
2=Not used
3=Not used
50 IPINT(Japan only)
Public PCS Protocol
0-5 = Not used
6 = IP Protocol (2B + D)
7 = Public PCS Protocol (2B + D)
8-15 = Not used
51 IPTRKIP Trunk
0 = Out of Service
1=In Service
52 CTCFCall Transfer/Forwarding Q.SIG
Supplementary Service
0 = Out of Service
1=In Service
53 RERTRerouting Function
0 = Out of Service
1=In Service
54 DCANSAnswer when DC Dialing
0 = Out of Service
1=In Service
55 RNDTrunk Select Data in Round Robin Formula
0 = Out of Service
1=In Service
56 CLBKKind of Collect Call Blocking Signal (for Brazil only)
0 = GB-7 1 = GB-3
57 UALAWUser Information for Layer 1 Protocol
0 = Transparent
1 = 
µ-law output
2 = A-law output
3 = Not used CDN ROUTE NUMBER
TRUNK DATA
    Add page 686 to Favourites
    image text
    Enable zoom 
    							CHAPTER 4 NDA-24298
Page 652
Issue 1
ARTIN : Assignment of Trunk Application Data for NDM
ARTIN: Assignment of Trunk Application Data for NDM
1. General
This command assigns and deletes trunk application data in Fusion Network. The data assigned by this
command is written in the Network Data Memory (NDM) of the Network Control Node (NCN), updating the
NDM at each Local Node (LN).
2. Precautions
1. This command can be used only when logging in to NCN (Network Control Node).
2. The data assigned by this command is also allocated to the Trunk Application data for physical route
(ARTI). If the Trunk Application data is deleted by using this command, however, the data for physical
route is not to be deleted. Therefore, use the ARTI command to invalidate the Trunk Application Data for
physical route.
3. Data Entry Instructions
See data sheet in Section 4.
    Add page 687 to Favourites
    image text
    Enable zoom 
    							NDA-24298 CHAPTER 4
Page 653
Issue 1
ARTIN : Assignment of Trunk Application Data for NDM
4. Data Sheet
CDNLOGICAL ROUTE NUMBER (1-899)
TRUNK DATA
1 RST Assignment of Restart 
0 = Restart Send per Individual Channel
1 = Not used  2 = Not used
3 = Restart not Send
2 HMT  When assigning this data, always enter zero (0). 0 0 0 0
3 TRCRST Call Restriction by Information transfer rate in 
Bearer Capability Information Element 
0 = No restriction
1 = Data call restriction (Unrestricted digital, Re-
stricted digital and Video data calls are re-
stricted.)
2 = Speech call restriction (Speech, 3.1 kHz 
audio and 7 kHz audio calls are restricted.)
3-15 = Not used
4 TRSRST Call Restriction by Information transfer rate in 
Bearer Capability Information Element 
0 = No restriction 
1 = 384 Kbps (H0) call is restricted
2 = 1536 Kbps (H11)/1920 Kbps (H12) call is 
restricted.
3 = 384 Kbps and 1536 (H11)/1920 Kbps (H12) 
calls are restricted.
4-15 = Not used
5 T309LNK Assignment of Timer T309 for Data Link 
Failure
0 = Layer 2 Alarm with T309 for Data Link 
Failure 
1 = Layer 2 Alarm [Temporary] with T309 is 
enabled 
2 = Layer 2 Alarm [Permanent] with T309 is en-
abled 
3 = Not used
6 T309CON Assignment of Timer T309 for Layer 1 Failure
0 = Layer 1 Alarm with T309 is disabled 
1 = Layer 1 Alarm [Temporary] with T309 is 
enabled
2 = Layer 1 Alarm [Permanent] with T309 is en-
abled 
3 = Not used
    Add page 688 to Favourites
    image text
    Enable zoom 
    							CHAPTER 4 NDA-24298
Page 654
Issue 1
ARTIN : Assignment of Trunk Application Data for NDM
7 LLCRST Call Restriction by user rate in Low Layer 
Capability Information Element 
0 = No restriction
1-31 = Call which includes this user rate value is 
restricted. 
Note
Note:User rate value is based on 
ITU-T Q-931. 
8 VCM  When assigning this data, always enter zero (0). 0 0 0 0
9 OVRT  When assigning this data, always enter zero (0). 0 0 0 0
10 POOL When assigning this data, always enter zero (0). 0 0 0 0
11 DTRT Deletion of ALL 1 alarm signal (DTI Layer 1 
alarm) 
0 = Not used
1 = Deletion of ALL 1 alarm signal as a Layer 1 
alarm 
12 TMPRT Temporary Route Information over CCIS 
0 = Not used 
1 = In CCIS, the route information can be 
transferred by the call control messages. 
Moreover, the call restriction can be 
checked referring to this route information. 
13 CODEC  When assigning this data, always enter zero (0). 0 0 0 0
14 PASS When assigning this data, always enter zero (0). 0 0 0 0
15 IRL Clear call when DTI alarm is detected
0 = Not used
1 = Clear call when DTI alarm is detected.
Note:
This data should be set when 
there is no Dch in the 
physical DTI. 
16 MTC Assignment of Timer T309 Value.
Restoration timer (TC×MTC) sec.
0-15 = TC×MTC (Restart timer value)
17 TC Timer T309 Counter Value
0 = Not used   1 = 64 msec. 
2 = Not used   3 = 2 sec.
4 = 30 sec.   5 = 5 min.
6 = 1 sec.   7 = Not used 
18 TS  When assigning this data, always enter zero (0). 0 0 0 0
19 CDCSPD When assigning this data, always enter zero (0). 0 0 0 0
CDNLOGICAL ROUTE NUMBER (1-899)
TRUNK DATA
    Add page 689 to Favourites
    image text
    Enable zoom 
    							NDA-24298 CHAPTER 4
Page 655
Issue 1
ARTIN : Assignment of Trunk Application Data for NDM
20 DVRST Call restriction while Tie Line is backed up on 
ISDN. 
0 = No restriction
1 = Speech call restriction (Speech. 3.1 kHz 
audio, 7 kHz audio calls are restricted)
2 = Data call restriction (Unrestricted digital, 
restricted digital and Video data are 
restricted.) 
3 = Both Speech and Data calls are restricted. 
21 RSCT Call restricted by Temporary Route Information 
0 = No restriction
 1 = Restriction
Note:
This data is effective when
TMPRT = 1. 
22 ROCG Outgoing Call Account by Temporary Route 
Information 
0 = Not used   1 = Effective 
Note:
This data is effective when
TMPRT = 1. 
23 RICG Incoming Call Account by Temporary Route 
Information
0 = Not used   1 = Effective
Note:
This data is effective when
TMPRT = 1. 
24 STSENQ Status Inquiry Message Send 
0 = Out of service   1 = In service
25 MMNPASS When assigning this data, always enter zero (0). 0 0 0 0
26 DLTK   (Japan only)
When assigning this data, always enter zero (0).0000
27 CALN (Japan only)
When assigning this data, always enter zero (0).0000
28 NETINT (Japan only)
When assigning this data, always enter zero (0).
0000
29 INBAND  When assigning this data, always enter zero (0).0000
30 RETMSG (Australia only) 
Return Massage for Connect ISDN LINE with 
Analog Trunk
0 = CALL PROC. + ALERT
1 = CALL PROC. + ALERT or CALL PROC. 
+ PROGRESS
CDNLOGICAL ROUTE NUMBER (1-899)
TRUNK DATA
    Add page 690 to Favourites
    image text
    Enable zoom 
    							CHAPTER 4 NDA-24298
Page 656
Issue 1
ARTIN : Assignment of Trunk Application Data for NDM
31 ANI Timing to demand ANI Information 
0 = There is no ANI demand at Incoming call
1 = After receiving 1st digit
2 = After receiving 2nd dig it 
3 = After receiving 3rd dig it 
4 = After receiving 4th digit 
5 = After receiving 5th digit
6 = After receiving 6th digit 
7 = After receiving 7th digit
32 SRV (Australia only)
Additional Service Selection 
bit 0 = Advice of Charge (AOC) 
0 = Valid   1 = Invalid
bit 1 = Malicious Call Trace (MCT)/Malicious 
Call Identification (MCID) 
0 = Valid  1 = Invalid
bit2-bit6 = Not used 
bit7 = For TON and/or NPI
0 = Invalid   1= Valid 
Note:
Input this data by a decimal. 
33 TON Type of Number 
0 = Unknown
1 = International Number 
2 = National Number 
3 = Network Special Number
4 = Subscriber Number  5 = Not used
6 = Abbreviated Number 
7 = Reserved for Extension
Note:
This data is effective when
ARTD, INT = 4 and SRV bit7
= 1 is assigned. 
34 NPI Numbering Plan Identification
0  =  Unknown         
1 = ISDN/Telephony Numbering Plan
2 = Not used 
3 = Data Numbering Plan 
4 = Telex Numbering Plan 
5-7  =  Not  used      
8 = National Standard Numbering Plan
9 = Private Numbering Plan 
10-14 = Not used 
15 = Reserved for Extension 
Others = Not used
Note:
This data is effective when
ARTD, INT = 4 and SRV bit7
= 1 is assigned.
CDNLOGICAL ROUTE NUMBER (1-899)
TRUNK DATA
    All NEC manuals Comments (0)

    Related Manuals for NEC Neax 2400 Ipx Office Data Specification