NEC Neax 2400 Ipx Office Data Specification
Have a look at the manual NEC Neax 2400 Ipx Office Data Specification online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1168 NEC manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
NDA-24298 CHAPTER 4 Page 907 Issue 1 ASYDN : Assignment of System Data in Network Data Memory 15b 0 Access Code for C.F.-Busy Line and C.F.-Don’t Answer Services 0/1 = Same/Separate Note:If “0” is assigned, assign either SID: 10 or 12 in the ASPA command. b 1Maximum number of Multiple Call Forwarding - All Calls/ Busy Line occurrences: b3b2b1b3b2b1 000: 100 : four times 001: once 101 : 010: twice 110 : five times 011: three times 111 : Note:This data is valid when SYS-1, INDEX 69, bit7 is assigned as “1.” b 2 b3 b4Miscellaneous Timer Counter (MTC) (0 - 7)Call Back - Delay Timer Timer Value Setting is MTC × 2 sec. When this data is “000,” Timer Value is 2 sec.b5 b6 b7 Call Back - Delay Timer 0/1 = Ineffective/Effective 600 Not used 700Not used 8Number of Tenants 9 Number of Attendant Consoles 1IMG: 1~16 (01Hex~10Hex) 4IMG: 1~32 (01Hex~20Hex) IPX-U (16IMG): 1~60 (01Hex~3C Hex) Note:When the attendant console/desk console is not used, assign “00H” here. 10 00 Not used 15 00Not used SYSTEM DATA TYPE (SYS)SYSTEM DATA INDEX (INDEX) 0 -1535DATA (DATA) 00 – FF (Hex)BIT CORRESPONDING DATA SYSTEM DATA CONTENTS (MDATA) DATA 0/1BIT ~~~
CHAPTER 4 NDA-24298 Page 908 Issue 1 ASYDN : Assignment of System Data in Network Data Memory 116 b0 1 - digits Station Number 0/1 = Out/In Service b1 2 - digits Station Number 0/1 = Out/In Service b2 3 - digits Station Number 0/1 = Out/In Service b3 4 - digits Station Number 0/1 = Out/In Service b4 5 - digits Station Number 0/1 = Out/In Service b5 6 - digits Station Number 0/1 = Out/In Service 0 b6Not used 0b7 17 b0 This bit (data “1”) allows single line stations to switch hook flash and dial an access code while hearing RBT, to place a voice call to a D term or activate the Dterm’s Message Reminder Key. 0/1 = Out/In Service b1 Not used b2 b3 b4 b5 b6 b7 18 00Not used 19 00 Not used SYSTEM DATA TYPE (SYS)SYSTEM DATA INDEX (INDEX) 0 -1535DATA (DATA) 00 – FF (Hex)BIT CORRESPONDING DATA SYSTEM DATA CONTENTS (MDATA) DATA 0/1BIT
NDA-24298 CHAPTER 4 Page 909 Issue 1 ASYDN : Assignment of System Data in Network Data Memory Note 1:Index 20 Bit 7 = 0 Station B or RT + TRK of Calling Party is provided as originator of call on SMDR output. Note 2:b 7 = 1 Station A is output as the originator in both cases. 1200 b0 Not used 0 b1 0b2 0b3 0b4 0b5 0b6 b7 Billing Party for a call transferred by Call Forwarding - Outside Service Note:When “1’ has been assigned to b7, the Station Number A (Called Party), as shown in the figure below, is provided to the SMDS equipment. 0 = The Billing Party is the originator of the transferred call. 1 = The Billing Party is the station that has set Call Forwarding - Outside service. SYSTEM DATA TYPE (SYS)SYSTEM DATA INDEX (INDEX) 0 -1535DATA (DATA) 00 – FF (Hex)BIT CORRESPONDING DATA SYSTEM DATA CONTENTS (MDATA) DATA 0/1BIT STN A STN A STN B TRK AOutside Par ty Calling Par ty Outside Par ty *STN A has set Call Forwarding-Outside service.
CHAPTER 4 NDA-24298 Page 910 Issue 1 ASYDN : Assignment of System Data in Network Data Memory SYSTEM DATA TYPE (SYS)SYSTEM DATA INDEX (INDEX) 0 – 1535DATA (DATA) 00 – FF (Hex)BIT CORRESPONDING DATA SYSTEM DATA CONTENTS (MDATA) DATA 0/ 1 BIT 121 00 Not used 22 00Not used 23 00Not used 24 00Not used 25 00Not used 26 00Not used 270b 0 Not used 0b 1 0b2 0b3 0b4 0b5 0b6 0b7 Immediate Ring Back Tone Sending: 0/1 = Not Required/Required 28 00 Not used
NDA-24298 CHAPTER 4 Page 911 Issue 1 ASYDN : Assignment of System Data in Network Data Memory 129~32 00 Not used 330b 0 Not used 0b1 0b2 b3Telephone Subject to Total Billing (when b6 = 1) b4b3 0 0 = Telephone that called first. 0 1 = Telephone that called last. 1 0 = First telephone after the call has been handled by AT T . 1 1 = Last telephone after the call has been handled by AT T . b 4 b5 Billing for Transferred Incoming Call 01/ = Split/Total Billing Note:Total Billing means “telephone that called last.” b 6 Billing for Transferred Outgoing Call 0/1 = Split/Total Billing Note:Total Billing means “telephone that called last.” b 7Not used 34~40 00 Not used 41b0~b6 OG Queuing Override - DDD Seizing Timer (for Fusion Ser- vice) Timer Counter (TC) is to be assigned a value from 01 Hex to 7F Hex. Timer Value Setting is (TC) × 30 sec. Note:When this data (TC) is 00 Hex, default data of 3 minutes is set. 0b 7Not used SYSTEM DATA TYPE (SYS)SYSTEM DATA INDEX (INDEX) 0 – 1535DATA (DATA) 00 – FF (Hex)BIT CORRESPONDING DATA SYSTEM DATA CONTENTS (MDATA) DATA 0/ 1 BIT
CHAPTER 4 NDA-24298 Page 912 Issue 1 ASYDN : Assignment of System Data in Network Data Memory 142b 0Not used b 1Not used b 2Not used b 3Not used b 4Not used b 5Not used b 6Not used b 7 SST, SPDT Tone 0/1 = Continuous/Burst 43 00 Not used 46 00Not used 47b 0Traffic Measurement Indication 0/1 = CCS Indication/Erlang Indication 0b 1~b6Not used b 7 Traffic Measurement for Terminal and Route Traffic (ATRFN) 0/1 = Out/In service 48-58 00 Not used 590b 0Not used 0b 1Not used b 2DID Busy Condition 0/1 - Not Tone/ROT 0b 3Not used 0b 4Not used 0b 5Not used 0b 6Not used 0b 7Not used 600b 0~b2Not used b 3 UCD Queuing - Fusion 0/1 = Available/Unavailable 0b 4~b7Not used SYSTEM DATA TYPE (SYS)SYSTEM DATA INDEX (INDEX) 0 – 1535DATA (DATA) 00 – FF (Hex)BIT CORRESPONDING DATA SYSTEM DATA CONTENTS (MDATA) DATA 0/ 1 BIT ~~~
NDA-24298 CHAPTER 4 Page 913 Issue 1 ASYDN : Assignment of System Data in Network Data Memory 161-64 00 Not used 65 Maximum Number of Routes 1-255 = 01FF Hex. 66 00Not used 67 00Not used 68b 0 Operating method for busy station service (Call Back, Executive Right of Way, etc.) 0/1 = SHF × Access Code/SHF × Access Code and Last Digit × Access Code 0b 1Not used 0b 2Not used b 3 OG Trunk Queuing (On-Hook) Automatic Cancel (for Fusion Service) 0/1 = Out/In Service 0b 4Not used 0b 5Not used 0b 6Not used 0b 7Not used 690b 0 Not used 0b 1 0b2 0b3 0b4 b5 Hunting Group when transferred party is busy (Station Hunting after C.F. - Busy Line) (for Fusion Service) 0 = Hunt in Transferring Party’s Group 1 = Hunt in Transferred Party’s Group 0b 6Not used b 7 Multiple Call Forwarding - Busy Line/All Calls (for Fusion Service) 0/1 = Out/In Service SYSTEM DATA TYPE (SYS)SYSTEM DATA INDEX (INDEX) 0 – 1535DATA (DATA) 00 – FF (Hex)BIT CORRESPONDING DATA SYSTEM DATA CONTENTS (MDATA) DATA 0/ 1 BIT
CHAPTER 4 NDA-24298 Page 914 Issue 1 ASYDN : Assignment of System Data in Network Data Memory 1700b 0 Not used 0b1 0b2 0b3 b4 One digit dialing instead of SHF (DP TEL only) 0/1 = Not Required/Required 0b 5Not used b 6 Announcement Trunks used for Delay Announcement - UCD service (for Fusion Service) 0/1 = Common/Per UCD group b 7 Send Warning Tone to interrupted parties when Executive Right of Way service is in operation 0/1 = Required/Not Required 71b 0Call Back Automatic Cancel Timer Va l u e = T X (× 1H to XFH) × MTC (3.5 minutes) This Timer can be assigned a value from 3.6 minutes to 52.5 minutes. b 1 b2 b3 0b4 Not used 0b5 0b6 b7 Enable Call Back Automatic Cancel Timer 0/1 = No/Yes 72 00 Not used 73 00Not used 74 00Not used 75 00Not used 76 00Not used SYSTEM DATA TYPE (SYS)SYSTEM DATA INDEX (INDEX) 0 – 1535DATA (DATA) 00 – FF (Hex)BIT CORRESPONDING DATA SYSTEM DATA CONTENTS (MDATA) DATA 0/ 1 BIT
NDA-24298 CHAPTER 4 Page 915 Issue 1 ASYDN : Assignment of System Data in Network Data Memory 1770b 0Not used 0b 1 b2 MW Refresh 0/1 = Required/Not Required Note:When message Waiting Lamp is provided, this data should be assigned “0.” 0b 3 Not used 0b 4 0b5 0b6 0b7 781b 0 Calling and Intermediate Station Number indication (Dterm and ATTCON) 0/1 = Out/In Service (Always assign “1.”) 1b 1 Kind of Service Class indication (Dterm ) 0/1 = Out/In Service (Always assign “1.”) 1b 2 Not used 0b 3 0b4 0b5 0b6 0b7 790b 0Not used 0b 1 b2 Split Call Forwarding Service 0/1 = In/Out Service 0b 3 Not used 0b 4 0b5 0b6 0b7 SYSTEM DATA TYPE (SYS)SYSTEM DATA INDEX (INDEX) 0 – 1535DATA (DATA) 00 – FF (Hex)BIT CORRESPONDING DATA SYSTEM DATA CONTENTS (MDATA) DATA 0/ 1 BIT
CHAPTER 4 NDA-24298 Page 916 Issue 1 ASYDN : Assignment of System Data in Network Data Memory 180 00 Not used 90 00Not used 910b 0Not used 0b 1 b2Grades of System Message that can be registered: b 3b2 0 0 = Register All System Message Data 0 1 = Register System Message Data higher than grade 1 (SUP, MN, MJ) 1 0 = Register System Message Data higher than grade 2 (MN, MJ) 1 1 = Register System Message Data higher than grade 3 (MJ) b 3 0b4 Not used 0b5 0b6 0b7 92~158 00 Not used 159b 0~b6 OG Trunk Queuing Automatic Cancel Timer (for Fusion Ser- vice): Miscellaneous Timer Counter (MTC) is to be assigned a val- ue from 0 Hex to 7F Hex (0~127).The duration before the OG Queuing memory becomes cleared if no trunks become idle. Timer Value Setting is MTC × 30 sec. Note:When this data is 00 Hex, default data is automatically set to 30 min. This timer is effective when ASYDN, SYS1, INDEX 68, b 3 = “1.” b7Not used 160 00 Not used 161b 0~b5Not used b 6 Timing Start using “#” code 0/1 = Ineffective/Effective b 7 Timing Start using “*” 0/1 = Ineffective/Effective SYSTEM DATA TYPE (SYS)SYSTEM DATA INDEX (INDEX) 0 – 1535DATA (DATA) 00 – FF (Hex)BIT CORRESPONDING DATA SYSTEM DATA CONTENTS (MDATA) DATA 0/ 1 BIT ~~~