NEC Neax 2400 Ipx Office Data Specification
Have a look at the manual NEC Neax 2400 Ipx Office Data Specification online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1168 NEC manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
NDA-24298 CHAPTER 4 Page 447 Issue 1 AKYD : Assignment of Key Data for Dterm FKY KEY NUMBER (KYN)SERVICE CONDITION (KYI) 0-2MULTI LINE RING INFORMATION FOR EACH LINE (RG)INTERCOM KIND OF INCOM (ICM) 0-2GROUP ID NUMBER (G-ID) 1-50 FEATURE KEY CODE (FKY)KIND OF LINE (KD) 0-2STATION NUMBER (STN) TENANT NUMBER (TN) See the Table 4-12. G-ID KD 0 = Line 1 = Intercom 2 = DSS Key RG See the Table 4-13 for RG data 0-7. ICM 0 = Automatic 1 = Manual 2 = Dial Enter unique number for each Intercom group within the range from 1 to 50. KYI Enter the type of keys. 0 = Key is not used 1 = Function Key 2 = Multi-Line KEY NUMBER (KYN)SERVICE CONDITION for FLEX KEYS (KYI 2) 0/1 1 2 KYI 2 Enter the type of keys. 0 = Key is not used 1 = Function Key FEATURE KEY CODE for FLEX KEYS (FKY2) FKY 2 See the Table 4-12. 1 2 For the Line/Feature keys For the Flex keys
CHAPTER 4 NDA-24298 Page 448 Issue 1 AKYD : Assignment of Key Data for Dterm Table 4-12 FKY 1 2 3 4 5 6 7 8 10 11 12 13 14 15 16 17 18 19 20 21 22 23-25Call Forwarding-Busy Line Call Forwarding-All Calls Executive Right of Way Call Waiting Call Back Message Reminder Save and Repeat Last number call Boss-Secretary-Message Waiting Lamp Control; Set Call Hold Boss-Secretary-Message Waiting Lamp Control; Cancel Call Pickup-Group Three-way Calling Voice Call Speed Calling-System Function CAS SHF Call Transfer - All Calls UCD Busy Out Non-Exclusive Hold/Exclusive Hold (Hold) Flash Button Call Forwarding-Dont Answer - FKY Service name FKY Service nameFKY Service nameFKY(1-320) 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53-54 55 56 57 58 59 60 61-82 83 84 85 86 87 88 89OAI Key Code 2 OAI Key Code 3 OAI Key Code 4 OAI Key Code 5 OAI Key Code 6 OAI Key Code 7 OAI Key Code 8 OAI Key Code 9 OAI Key Code 10 OAI Key Code 11 OAI Key Code 12 OAI Key Code 13 UCD Call Waiting Lamp (In case Business Application)/END (END)/(In case Hotel Application) /OAI Key Code 14 Privacy Release Speed Calling - One Touch Do Not Disturb Microphone Speaker - PAGE OFF/ON HOOK FOR HEADSET Recall - Release Key Manual Signaling Key - Retain Conference Serial Call Internal Zone Paging - Wake Up Set (Note 1) Wake Up Reset Do Not Disturb Set (Note 2) 26 27 28 29 30Speed Calling-Station Originate (ORG) Answer (ANS) Data (DATA) Display/Auto (DSPY/AUTO)90 91 92 93 94 95 96 97 98 99 100 101 102-112 113 114 115 116 117 118 119 120 121 122Do Not Disturb Reset Room Cut Off Set (Note 3) Room Cut Off Reset Message Waiting Set (Note 4) Message Waiting Reset Check In Check Out Status Audit Enter Clear Enter END - Call ID change display - Call pickup expand - Ringer mute Call Return - Next page of software keys (Scroll key) Previous page of software keys (Back Scroll Key) Soft Key Assignment 123 124 125 126 127 128 129 130 131 132-320Off Hook Ringing (OFR) Mute (MUTE) Head Set (HSET) PS key Boss Move Call Block Call Trace - Disconnect Key - * * * * * * * * * * ** * * * * * * 9 31 32 33 34Data Transfer (DTX) - Message Waiting Lamp (MW) OAI Key Code 1 This service is activated without releasing service restriction by ASFC. (Whether the service is re- stricted or not, this feature is activated.) Note 1:Fo r G u e s t Dterm in the Hotel application, this FKY is used for the WU status lamp. Note 2:Fo r G u e s t Dterm in the Hotel application, this FKY is used for the DND status lamp. Note 3:Fo r G u e s t Dterm in the Hotel application, this FKY is used for the RC status lamp. Note 4:Fo r G u e s t Dterm in the Hotel application, this FKY is used for the MW status lamp.
NDA-24298 CHAPTER 4 Page 449 Issue 1 AKYD : Assignment of Key Data for Dterm 4. Data Sheet (a) When KD = 0/1 (for key assignment of Line key/Intercom key) Table 4-13 RG RG (0-7)RINGING DELAY TIME DAY NIGHT 0 NO (No Ringing) No Ringing 1 YES (Ringing) No Ringing 0 sec. 2 NO (No Ringing) Ringing 0 sec. 3 Not used Not used 4 YES (Ringing) Ringing 30 sec. 5 YES (Ringing) Ringing 20 sec. 6 YES (Ringing) Ringing 10 sec. MY LINE TENANT NUMBER (TN)STATION NUMBER (STN) PRIORITY OF ANSWERING CALL (PRI) 0-4PRIME LINE ALLOW OG FROM PRIME LINE (S) 0/1MESSAGE WA I T I N G DATA DISPLAY SELECTION (MWD) 0/1LINE PREFERENCE (LN PRE) 0/1LINE PREFERENCE FOR SPEAKER BUTTON (SPK) 0-3LINE PREFERENCE FOR ANSWER BUTTON (ANS) 0-2LINE PREFERENCE FOR OUTGOING BUTTON (ORG) 0/1TYPE OF DTERM (TP) 0-3 TENANT NUMBER (PL TN)STATION NUMBER (PL STN) KEY NUM- BER (KYN)SERVICE CONDITION (KYI) 0 – 2FEATURE KEY CODE (FKY) 1-320KIND OF LINE (KD) 0-2MULTI LINE INTERCOM TENANT NUMBER (TN)STATION NUMBER (STN)RING INFORMATION FOR EACH LINE (RG) 0-7KIND OF INCOM (ICM) 0-2GROUP ID NUM- BER (G-ID) 1-50 1 2 3 4 5 6 7 8 9 10 11 12 13
CHAPTER 4 NDA-24298 Page 450 Issue 1 AKYD : Assignment of Key Data for Dterm 14 15 16 17 18 19 20 21 22 23 24 25 26 MY LINE TENANT NUMBER (TN)STATION NUMBER (STN) PRIORITY OF ANSWERING CALL (PRI) 0-4PRIME LINE ALLOW OG FROM PRIME LINE (S) 0/1MESSAGE WA I T I N G DATA DISPLAY SELECTION (MWD) 0/1LINE PREFERENCE (LN PRE) 0/1LINE PREFERENCE FOR SPEAKER BUTTON (SPK) 0-3LINE PREFERENCE FOR ANSWER BUTTON (ANS) 0-2LINE PREFERENCE FOR OUTGOING BUTTON (ORG) 0/1TYPE OF DTERM (TP) 0-3 TENANT NUMBER (PL TN)STATION NUMBER (PL STN) KEY NUM- BER (KYN)SERVICE CONDITION (KYI) 0 – 2FEATURE KEY CODE (FKY) 1-320KIND OF LINE (KD) 0-2MULTI LINE INTERCOM TENANT NUMBER (TN)STATION NUMBER (STN)RING INFORMATION FOR EACH LINE (RG) 0-7KIND OF INCOM (ICM) 0-2GROUP ID NUM- BER (G-ID) 1-50
NDA-24298 CHAPTER 4 Page 451 Issue 1 AKYD : Assignment of Key Data for Dterm Note 1:When KYI = None, it is not necessary to assign any data. Note 2:When KYI = FUNCTION, assign data for FKY only. Note 3:When KYI = Multi-Line, assign data for multiple telephone only. KEY NUM- BER (KYN)SERVICE CONDITION (KYI) 0 – 2FEATURE KEY CODE (FKY) 1-320KIND OF LINE (KD) 0-2MULTI LINE INTERCOM TENANT NUMBER (TN)STATION NUMBER (STN)RING INFORMATION FOR EACH LINE (RG) 0-7KIND OF INCOM (ICM) 0-2GROUP ID NUM- BER (G-ID) 1-50 27 28 29 30 31 32 33 34 35 36 37 38 39 40 F1 F2 F3 F4 F5 F6 F7 F8
CHAPTER 4 NDA-24298 Page 452 Issue 1 AKYD : Assignment of Key Data for Dterm (b) When KD = 2 (for key assignment of DSS Console). KEY NUMBERTENANT NUMBER (TN)STATION NUMBER (STN) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
NDA-24298 CHAPTER 4 Page 453 Issue 1 AKYD_T : Assignment of Key Data for Dterm – Telephone Number AKYD_T: Assignment of Key Data for Dterm – Telephone Number 1. General This command assigns the Line Key, Function Key, Intercom Key, and DSS Key data corresponding to each line/feature button on a D term. The station data of AKYD command can be assigned by using Telephone Number. 2. Precautions 1. Only the Telephone Numbers assigned by the ALGSN command can be used. Telephone Numbers by the ALGSL command is not available in this command. 2. In case logging in to a LN, only the Telephone Numbers allocated to the stations within the logged-in node can be used in this command. Also, when logging in to the NCN, the data memory of the whole nodes in the network is to be written. 3. Prior to this command, Telephone Numbers must be allocated by using the ALGSN command. Only the Telephone Numbers assigned by the ALGSN command can be used. Telephone Numbers by the ALGSL command is not available in this command. 4. The D term series III (16-button type) and Dterm series E have the default key data. (Refer to Precautions 8.) If the default data is to be used, assignment in AKYD/AKYD_T is not necessary. The table below shows the specification pertaining to data assignment for the D term. 5. Before assigning the key data for a D term using this command, be sure to assign the station data of the Dterm using the ASDT command (TN, STN, TEC = 12 (Dterm)). The station number assigned by the ASDT command is referred to as “MY LINE”. Note Note: This “MY LINE” corresponds to the physical port associated with the LENS of a ELC card. 6. By assigning another station line to a feature button using this command, an incoming call terminated to a station line other than My Line can be answered or can be transferred to elsewhere as in the case of the My Line. A station line other than My Line is referred to as a “Sub Line.” A “Sub Line” can be assigned not only to a D term but to any conventional telephone. In addition, the station data for My Line and Sub Line must be assigned by the ASDT command before the key data is assigned. When the Sub Line and the My Line belong to different tenants, use the ATNR command and clear the “Tenant-to-Tenant Restriction.” Table 4-14 Data Assignment for the Dterm TYPE OF DtermLINE/FEATURE BUTTON NUMBER OF BUTTONS Series III8-button type KYN = 1-8 8 16-button type KYN = 1-16 16 24-button type KYN = 1-24 24 Series E8-button type KYN = 1-8 8 16-button type KYN = 1-16 16 32-button type See Figure 4-732
CHAPTER 4 NDA-24298 Page 454 Issue 1 AKYD_T : Assignment of Key Data for Dterm – Telephone Number 7. A Multi-Line key (the key for My Line and Sub Line) on the Dterm can be assigned as Prime Line. If the Prime Line is not assigned, the My Line serves as the Prime Line. When the user goes off-hook, the Prime Line is automatically selected on the D term. 8. A virtual line can be assigned as a Sub Line of the D term. The virtual line can be used the same way as the My Line for outgoing calls and other service operations. Note Note: Virtual Line --- A virtual LENS exists only in memory, but does not exist physically. Data can be assigned but no hardware is required. Example:LENS = 000311. The virtual LENS is assigned by the ASDT command in the same way as an ordinary line. (The telephone class is TEC = 18: Virtual Line) 9. If the station user accepts the default settings, the data assignment of this command is not required. The default data for each line/feature button is shown below. 10. The ability to assign Sub Line appearances across module groups is available when ASYD command SYS1, INDEX321, bit0 = 1 is assigned. Stations can appear on D term which accommodated the different module group within the same IMG. 11. When assigning the line/feature buttons as function keys, take the following precautions: (a) My Line key must be programmed. (b) Not used line/feature buttons should be assigned as KYI = 0 (Not used) (c) The following function keys are basically fixed: FKY = 13: CONF (Three - Way Calling) FKY = 18: TRANSFER (Call Transfer - All Calls) FKY = 20: HOLD (Non - Exclusive Hold/Exclusive Hold) FKY = 28: ANSWER FKY = 51: MIC FKY = 52: SPEAKER FKY = 57: RECALL Table 4-15 Default Data for Each Line/Feature Button KEY NO.DEFAULT DATAKEY NO.DEFAULT DATA 1 CALL PICKUP 9 PRIME LINE 2 CALL FORWARDING - BUSY LINE 10 SPEED CALLING ONE-TOUCH 3CALL FORWARDING - ALL CALLS CALL FORWARDING - DON’T ANSWER11 SPEED CALLING ONE-TOUCH 4 EXECUTIVE RIGHT OF WAY 12 SPEED CALLING ONE-TOUCH 5 VOICE CALL 13 SPEED CALLING ONE-TOUCH 6 MESSAGE REMINDER 14 SPEED CALLING ONE-TOUCH 7 SAVE AND REPEAT 15 SPEED CALLING ONE-TOUCH 8 LAST NUMBER CALL 16 SPEED CALLING - SYSTEM
NDA-24298 CHAPTER 4 Page 455 Issue 1 AKYD_T : Assignment of Key Data for Dterm – Telephone Number 12. The applicable tenant number (TN) range is designated by the ASYD command, SYS1, INDEX8. 13. There is no default key data provided for D term (8-button type). The key data for all the line/feature buttons must be programmed. When assigning the key data of the line/feature button, take the following precautions: (a) My Line Key must be assigned in KYN = 1-8, and KYN = 9-16 should be assigned KYI = 0 (Not used). (b) The following function keys are basically fixed: FKY = 13: CONF (Three-Way Calling) FKY = 18: TRANSFER (Call Transfer-All Calls) FKY = 20: HOLD (Non-Exclusive Hold/Exclusive Hold) FKY = 28: ANSWER FKY = 51: MIC FKY = 52: SPEAKER FKY = 57: RECALL (c) Not used line/feature buttons should be assigned KYI = 0 (Not used). 14. There is no default key data provided for D term (24-button type/32-button type). The key data for all of the line/feature buttons must be programmed. When assigning the key data of the line/feature button, take the following precautions: (a) My Line Key must be assigned in KYN = 1-24, and KYN = 25-40 should be assigned KYI = 0 (Not used). My Line in KYN = 17-24 cannot be assigned without assigning any Line Key or any Function Key in KYN = 1-16. (b) The following function keys are basically fixed. FKY = 13: CONF (Three-Way Calling) FKY = 18: TRANSFER (Call Transfer-All Calls) FKY = 20: HOLD (Non-Exclusive Hold/Exclusive Hold) FKY = 28: ANSWER FKY = 51: MIC FKY = 52: SPEAKER FKY = 57: RECALL (c) Not used line/feature buttons should be assigned KYI = 0 (Not used). 15. When using 16 ELCJ (SR 3295, PROG-B or later), the FKY = 49: Speed Calling-One Touch can be assigned to a maximum of 16 Key Numbers (KYNS). Note 1:Speed Calling-One Touch data can be saved by the BOSD command. Note 2:Assign the data to the Key Numbers (KYN) in the consecutive order.
CHAPTER 4 NDA-24298 Page 456 Issue 1 AKYD_T : Assignment of Key Data for Dterm – Telephone Number 16. For Call Forwarding-Busy Line and Call Forwarding-Don’t Answer, refer to ASYD SYS1 Index5 (separate/common access for C.F.-Busy Line and C.F.-Don’t Answer). If common access codes are assigned, only one key is required to activate the features. If separate access codes are assigned, separate function keys must be assigned. 17. The FKY = 55: One-Touch changeover (PAGE) should be assigned when registering destination numbers greater than 20 as one-touch speed calling codes. The FKY = 55: One-Touch changeover (PAGE) should be assigned when registering destination numbers greater than 16 as one-touch speed calling codes. Note:Each one-touch button is assigned a 2-page memory (Page 0 and Page 1). One destination number can be assigned on a page basis. When originating an outgoing call, the page of one-touch button can be designated by this function key. 18. In conjunction with intercom service, take the following precautions: (a) Before assigning the Intercom Key Data using this command, assign the Intercom Group Data using the command AICD/ADIM. (b) When providing the Intercom service, assign “The response priority when the SPEAKER button is pressed or the station goes off-hook” in the parameter PRI. When not providing the Intercom service, assign PRI = 0. 19. When this command is used, the ELC card must be reinitialized (MB switch UP-DOWN). 20. A maximum of 8 soft keys can be assigned via the function key (FKY=122). Note:6 soft keys available at the maximum when page scroll key soft key is displayed on the LCD. 21. Soft key data to be assigned via the function key (FKY=122) is not available for having the different function per each condition on the D term. 22. The same function data can not be assigned to both function key and soft key. 23. Expanded Multiple Line Operation - D term [E-26] service is available only when “KD = 0 (Line)” is entered. This service is not available when “KD = 1 (Intercom)” or “KD = 2 (DSS Key)” is assigned.