NEC Neax 2400 Ipx Office Data Specification
Have a look at the manual NEC Neax 2400 Ipx Office Data Specification online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1168 NEC manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
NDA-24298 CHAPTER 4 Page 767 Issue 1 ANCD : Assignment of Night Connection Data 4. Data Sheet MODULE GROUP NUMBER (MG) 00 - 31PFT CARD NUMBER (NCU PKG) 0 - 3PORT NUMBER OF PFT CARD (PORT) 0 - 11ROUTE NUMBER (RT) 1-255TRUNK NUMBER (TK)REMARKS 0 1 2 3 4 5 6 7 8 9 10 11 0 1 2 3 4 5 6 7 8 9 10 11
CHAPTER 4 NDA-24298 Page 768 Issue 1 ANCD_LR : Assignment of Night Connection Data – Logical Route Number ANCD_LR: Assignment of Night Connection Data – Logical Route Number 1. General This command is used when the Power Failure Transfer (PFT) circuit card is controlled by the external key. Route data of the ANCD command can be assigned by logical route number. 2. Precautions 1. Prior to this command, logical route data must be allocated by using the ALRTN command. 2. Only when logging in to the NCN (Network Control Node), this command can be used to assign the logical route data of self-Node and the other Nodes in the Fusion Network. If logging in to a LN (Local Node), data setting only for the self-node is available. (Error message is indicated if you try to write the data of other Node.) 3. When the “PFT control by the external key” is required, the following data assignments are needed: (a) AUNT command, TYPE = 2 (PFT) (b) AEKD command (c) ANCD/ANCD_LR command (d) ACSI command, CSI = 4 (Direct-in Termination (Night Mode)) 3. Data Entry Instructions FUSION POINT CODE (FPC) 1-253MODULE GROUP NUMBER (MG)PORT NUMBER OF PFT CARD (PORT) 0-11 PFT CARD NUMBER (NCU PKG) 0-3OUTSIDE ROUTE NUMBER (RT) LOGICAL ROUTE NUMBER (LGRT) 1-899REMARKS TRUNK NUMBER (TK) 1-255 MG Enter the data of PFT card assigned by the AUNT command. LGRT Enter the logical route number allocated to the external route number. TK Enter the trunk number connected to the corresponding circuit number of PFT card.FPC Enter the FPC of target Node only when logging in to the NCN (Network Control Node). PORT The port parameter corresponds to the circuit number of the PFT card.
NDA-24298 CHAPTER 4 Page 769 Issue 1 ANCD_LR : Assignment of Night Connection Data – Logical Route Number 4. Data Sheet FUSION POINT CODE (FPC) 1-253MODULE GROUP NUMBER (MG)PFT CARD NUMBER (NCU PKG) 0 - 3PORT NUMBER OF PFT CARD (PORT) 0 - 11LOGICAL ROUTE NUMBER (LGRT) 1-899OUTSIDE ROUTE NUMBER (RT)TRUNK NUMBER (TK) 1-255REMARKS
CHAPTER 4 NDA-24298 Page 770 Issue 1 ATAS : Assignment TAS Service Data ATAS: Assignment TAS Service Data 1. General This command assigns the data related to the Trunk Answer From Any Station (TAS) service feature. 2. Precautions 1. One tenant can be provided one TAS indicator. 2. The TAS answer access code is assigned by the ASPA command, SRV = SSC, SID = 16. 3. The TAS answering capability is assigned by the ASFC command, SFI=13 and the ACFR command, TSFI = 5. 4. The applicable Tenant Number (TN) range is designated by the ASYD command, SYS 1, INDEX 8. If data for this command is common for all tenants (ASYD command, SYS1, INDEX 93, bit2 = 1), assign TN parameter as data “1” for all tenants. 3. Data Entry Instructions TENANT NUMBER (TN)UNIT NUMBER (UNIT) 0-3 MODULE GROUP NUMBER (MG)CIRCUIT NUMBER (CN) 0/1REMARKS TN Enter the tenant number to be applied to the TAS service. UNIT Enter the Unit number of the TAS indicator. CN MG Enter the circuit number of the TAS indicator . Enter the module Group number the TAS indicator is mounted.
NDA-24298 CHAPTER 4 Page 771 Issue 1 ATAS : Assignment TAS Service Data 4. Data Sheet TENANT NUMBER (TN)MODULE GROUP NUMBER (MG)MOUNTED UNIT NUMBER (UNIT) 0 - 3CIRCUIT NUMBER (CN) 0/1REMARKS
CHAPTER 4 NDA-24298 Page 772 Issue 1 AEKD : Assignment of External Key Data AEKD: Assignment of External Key Data 1. General This command assigns the External Key related data, which allows a maintenance person to change the system over to the Day/Night mode by means of ON/OFF on the PFT circuit card. 2. Precautions 1. When the “PFT control by the external key” is required, the following data assignments are needed: (a) AUNT command, TYPE = 2 (PFT) (b) AEKD command (c) ANCD command (d) ACSI command, CSI = 4 (Direct-in Termination (Night Mode)) 2. A maximum of eight (0-7) external keys can be assigned, corresponding to each PFT circuit card. The external key can control two PFT circuit cards per MG (16 circuits). 3. Data Entry Instructions MODULE GROUP (MG) 0-7CIRCUIT CARD NO. (NCU PKG) 0/1EXTERNAL KEY NUMBER (CTN) 0-7CHANGE CONTROL PATTERN (CP) 1-4TN NUMBER OF INPUT TN or RT/TK (CNT) 1st 0 1 2 3 4 5 62nd 3rd 4th 5th 6th 7th 8th CP 1 = – 2 = Day/Night Change 3 = – 4 = –TN One external key can manage 8 tenants at the maximum
NDA-24298 CHAPTER 4 Page 773 Issue 1 AEKD : Assignment of External Key Data 4. Data Sheet MODULE GROUP NUMBER (MG) 0-7NCU CARD NUMBER (NCU PKG) 0/1EXTERNAL KEY NUMBER (CTN) 0-7CHANGE CONTROL PAT T E R N (CP) 1-4TENANT NUMBER (TN) 1ST 2ND 3RD 4TH 5TH 6TH 7TH 8TH 0 1 2 3 4 5 6 7
CHAPTER 4 NDA-24298 Page 774 Issue 1 AAND : Assignment of Automatic Number Identification Data AAND: Assignment of Automatic Number Identification Data 1. General This command assigns ANI data for the number of digits of the calling station number and the office code on each route basis for the Automatic Number Identification (ANI) Service. (For E911 ANI) 2. Precautions The route number set in parameter RT should have been designated in ARTD, ANI = 1. 3. Data Entry Instructions STA/ATT OUTGOING (AT) 0/1MAIN/ SATELLITE CENTRAL (CC) 0/1EXPAN- SION OF STA NUMBER LENGTH (KT) 0/1 OUT- GOING ROUTE NUMBER (RT) AT 0 = STA outgoing 1 = ATT outgoing These parameters vary depending on the assignment of the previous parameter. CENTRAL OFFICE CODE (COC) MAX. 5 DIGITSSTA NUMBER LENGTH (STNL) 1-8OFFICE CODE TO BE ADDED (ADD) 1-10CALL ORIGINA- TOR DIGIT TO BE SKIPPED (SKIP) 0-10OFFICE CODE (DC) MAX. 10 DIGITS CC 0 = Main Central 1 = Satellite Central KT 0 = OFF 1 = ON
NDA-24298 CHAPTER 4 Page 775 Issue 1 AAND : Assignment of Automatic Number Identification Data 4. Data Sheet (a) When STA/ATT, the Individual Attendant Number, is assigned. Outgoing and Main Central (AT = 0, CC = 0) Note:This parameter can be assigned when KT = 1. ROUTE NUMBER (RT)STA OUTGOING/ AT T OUTGOING (AT)MAIN CENTRAL/ SATELLITE CENTRAL (CC)EXPANSION OF STA NUMBER LENGTHS (KT) 0/1STA NUMBER LENGTH (STNL) 1 – 8 NoteOFFICE CODE TO BE ADDED (ADD) 1 – 10CALL ORIGINATOR DIGIT TO BE SKIPPED (SKIP) 0 – 10OFFICE CODE (DC) MAXIMUM 10 DIGITS 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
CHAPTER 4 NDA-24298 Page 776 Issue 1 AAND : Assignment of Automatic Number Identification Data (b) When STA/ATT, the Individual Attendant Number, is assigned. Outgoing and Satellite Central (AT = 0, CC = 1) ROUTE NUMBER (RT)STA OUTGOING/ AT T OUTGOING (AT)MAIN CENTRAL/ SATELLITE CENTRAL (CC)CENTRAL OFFICE CODE (COC) MAXIMUM 5 DIGITSOFFICE CODE TO BE ADDED (ADD) 1 – 10CALL ORIGINATOR DIGIT TO BE SKIPPED (SKIP) 0 – 10OFFICE CODE (DC) MAXIMUM 10 DIGITS 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01