NEC Neax 2400 Ipx Office Data Specification
Have a look at the manual NEC Neax 2400 Ipx Office Data Specification online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1168 NEC manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
NDA-24298 CHAPTER 4 Page 57 Issue 1 ATIM : Assignment of Date and Time ATIM: Assignment of Date and Time 1. General This command sets the clock information for the system. Clock information is executed when Y is entered in the WRT? field and the Enter key pressed. 2. Precautions 1. The clock is assigned in military time. 2. Clock information assigned in this command is necessary for the following purposes: (a) To indicate time for D term and ATT (Desk Console/Hotel Console) (b) To specify the time for changing the route pattern for LCR (c) To specify the time and date for changing the number development for LCR (d) To specify the time for outgoing calls or for refusing incoming calls (e) To specify the start time for the routing diagnosis (f) To specify a length of time for Traffic Measurement (g) SMDR 3. The system automatically takes the leap year into account. 3. Data Entry Instructions Enter the digits with a range from 1 to 31. Enter 4 digits as the year. (For example:1999 or 2000) Enter the digits with a range from 1 to 60. Enter the digits with a range from 1 to 60. Enter the digits with a range from 1 to 24. Enter the digits with a range from 1 to 12.DAY MINUTE SECOND HOUR MONTH YEAR YEAR MONTH DAY HOUR MINUTE SECONDDATE TIME
CHAPTER 4 NDA-24298 Page 58 Issue 1 ATIMN : Assignment of Date and Time for NDM ATIMN: Assignment of Date and Time for NDM 1. General This command sets the clock information for all systems within the Fusion network. The time data assigned by this command is adjusted according to each LN’s time difference data assigned by the ATDF command, before updating the NDM at each LN. The completion of time data assignment for each LN is displayed on the MAT. 2. Precautions 1. Prior to this command, the time difference data for all nodes must be assigned to the NCN using the ATDF command. 2. The clock is assigned in military time. 3. Clock information assigned in this command is necessary for the following purposes: (a) To indicate time for D term and ATT (Desk Console/Hotel Console) (b) To specify the time for changing the route pattern for LCR (c) To specify the time and date for changing the number development for LCR (d) To specify the time for outgoing calls or for refusing incoming calls (e) To specify the start time for the routing diagnosis (f) To specify a length of time for Traffic Measurement (g) SMDR 4. The system automatically takes the leap year into account. 5. Clock information is executed when “Y” is entered in WRT? field and the Enter key pressed.
NDA-24298 CHAPTER 4 Page 59 Issue 1 ATIMN : Assignment of Date and Time for NDM 3. Data Entry Instructions YEAR Enter the 4 digits of the year. (For example: 1999 or 2000) DATE TIME YEAR MONTH DAY HOUR MINUTE SECOND DAY Enter the digits with a range from 1 to 31. MINUTE Enter the digits with a range from 1 to 60. MONTH Enter the digits with a range from 1 to 12. HOUR Enter the digits with a range from 1 to 24. SECOND Enter the digits with a range from 1 to 60.
CHAPTER 4 NDA-24298 Page 60 Issue 1 ASYD : Assignment of System Data ASYD: Assignment of System Data 1. General The ASYD/ASYDL command assigns the system data for the following node: Local Node (L/N)/Network Control Node (NCN) of the Fusion network. Stand-alone PBX 2. Precautions 1. The ASYD command contains the following indexes: SYS 1, INDEX 0-511 SYS 2, INDEX 0-15 SYS 3, INDEX 0-31 2. The ASYDL command contains the following indexes: SYS 1, INDEX 512-1535 SYS 2, INDEX 16-79 (Not used) 3. For detailed information, see the NEAX2400 IPX Fusion Network System Manual.
NDA-24298 CHAPTER 4 Page 61 Issue 1 ASYD : Assignment of System Data 3. Data Entry Instructions Define each bits corresponding data referring to the SYSTEM DATA CONTENTS SYSTEM DATA TYPE (SYS)DATA (DATA) 00-FF (Hex) SYSTEM DATA INDEX (INDEX) 0-511 BIT CORRE- SPONDING DATA DATA 0/1BITSYSTEM DATA CONTENTS DATA DATA BIT BIT DATA Hex 1 1b 0 b1 b2 b3 b4 b5 b6 b7 1 0 0 0 0 0 0n n+1 FF031 1 0 0 0 0 0 0b 0 b1 b2Not used Not used Not used Not used Not used Not used Number of zzz b 3 b4 b5 b6 b7 xxx service 0/1 = Not to be provided/To be provided yyy service 0/1 = Not to be provided/To be provided Convert from Binary DATA to Hexadecimal, and enter the Hex. value at DATA text box. 00000011 b 7b6b5b4b3b2b1b0 03
CHAPTER 4 NDA-24298 Page 62 Issue 1 ASYD : Assignment of System Data 4. Data Sheet SYSTEM DATA TYPE (SYS)SYSTEM DATA INDEX (INDEX) 0 – 511DATA (DATA) 00 – FF (Hex)BIT CORRESPONDING DATA SYSTEM DATA CONTENTS DATA 0/1BIT 10 Number of Module Group (MG) IPX = 01~08 (MG00~07) (For IPX-UMG System) 01 Hex~20 Hex (MG00~MG32) 101 Number of Main Processor (fixed to “01”) 2 b00/1 = Built-in ACDP is not provided/provided. Also number of memory package. 3 b1-b7Not used Configuration of Time Division System 01 = Single, 02 = Dual
NDA-24298 CHAPTER 4 Page 63 Issue 1 ASYD : Assignment of System Data 14b 0 Control of ORT all Busy Status 0/1 = ROT/Queue b 1 Recalling method when the caller has released with Emergency Call service 0/1 = SHF or Depressing Ground Button/Unconditional Re- calling Note:The operation procedure for recall is different depending on the D term Series III or Dterm Series E. Dterm III user operates with SHF. Dterm E user operates with transfer key. b 2Releasing Method for Station to Station Calling Service b 3b2 0 0 = Calling Party release 0 1 = Called Party release 1 0 = First Party release 1 1 = Both Party release Normally assign “First Party release” b 3 b4 Temporary Class Conversion/OAI Free Location Memory 0/1 = Not Required/Required Note:When setting outgoing restriction and toll restriction in CCIS using the caller’s RSC transferred by a call origination from the preceding office, data value “1” is assigned. Destination restriction and number restriction cannot be made using RSC. This data is assigned “1” when the authorization code is provided. b 5 PAD Control of 16LC circuit card (for Station to Station Calling only) 0/1: Required/Not Required b 6 One Burst of Ringing On Call Forwarding (C.F.) phone when C.F. – All Calls service has been assigned (analog phones only). 0/1 = Not Required/Required b 7 Emergency Call Printout 0/1 = No Printout/Printout SYSTEM DATA TYPE (SYS)SYSTEM DATA INDEX (INDEX) 0 – 511DATA (DATA) 00 – FF (Hex)BIT CORRESPONDING DATA SYSTEM DATA CONTENTS DATA 0/1BIT
CHAPTER 4 NDA-24298 Page 64 Issue 1 ASYD : Assignment of System Data 15b 0 Access Code for C.F.-Busy Line and C.F. – Don’t Answer Services 0/1 = Same/Separate Note:If “0” is assigned, assign either SID: 10 or 12 in command ASPA. b 1Maximum number of Multiple Call Forwarding – All Calls/ Busy Line occurrences: b 3b2b1b3b2b1 0 00: 100: four times 0 01: 101: 0 10: twice 110: 0 11: three times 111: Note:This data is valid when SYS-1, INDEX 69, bit 7 is assigned as “1.” b 2 b3 b4 Miscellaneous Timer Counter (MTC) (0-7)Call Back – Delay Timer Timer Value Setting is MTC × 2 sec. When this data is “000,” Timer value is 2 sec. b5 b6 b7 Call Back – Delay Timer 0/1 = Ineffective/Effective 6b 0 Special Transmitting Tone When Using Sender (Station) 0/1 = Not Required/Required (used with LCR/Speed Calling, etc.) 0b 1Not used b 2 Special Transmitting Tone When Using Sender (ATT) 0/1 = Not Required/Required (used with LCR/Speed Calling, etc.) 0b 3Not used b 4Key pattern on the right side of Attendant Console b 6b5b4b5 b6 0 00=pattern 1 1 00=pattern 4 Note:Do not set other pattern data. 0b 7Not used SYSTEM DATA TYPE (SYS)SYSTEM DATA INDEX (INDEX) 0 – 511DATA (DATA) 00 – FF (Hex)BIT CORRESPONDING DATA SYSTEM DATA CONTENTS DATA 0/1BIT once five times
NDA-24298 CHAPTER 4 Page 65 Issue 1 ASYD : Assignment of System Data SYS1, INDEX 6, b4 ~ b6: Note:Can change the key Function using the AAKP command. 1. Desk Console (Business) Key Pattern (a) Add-on Console Key Pattern 2. Hotel Desk Console Key pattern (a) Add-on Console Key pattern TRKSL SVC SC SCRN DND OverrideHWS BV WUS DDS RCS MWS Check In AUD WUR DDR RCR MWR Check out STS LDN EMGTIE BVBUSY TRKSLATND NANS SCRecall SVCTF (FRL)(FX) (ICPT)PA G E StartREC Mute Pattern 4 (b4=0, b5=0, b6=1) LDN EMGTIE BVBUSY TRKSLATND NANS SCRecall SVCTF (FRL)(FX) (ICPT)PA G E StartREC Mute Call Park Pattern 1 (b4=0, b5=0, b6=0) Call ParkDEST Answer Cancel Ta l k Hold SRC Release DEST Answer Cancel Ta l k Hold SRC Release CAS CCSA WATS Pattern 1 (b4=0, b5=0, b6=0) and pattern 4 (b4=0, b5=0, b6=1) LDN EMGTIE HPBusy DNDADM NANS OTRecall ICPTTF WAT SFX CCSAPA G E StartREC Mute GST Pattern 1 (b4=0, b5=0, b6=0)
CHAPTER 4 NDA-24298 Page 66 Issue 1 ASYD : Assignment of System Data (b) Add-on Console Key pattern 3. Desk Console (Business) Key pattern for Hotel application system (a) Add-on Console Key pattern (b) Add-on Console Key pattern TRKSL SC FRL CP DND OverrideCAS BV WUS DDS RCS MWS Check In AUD WUR DDR RCR MWR Check out STS CAS CCSA WATS CAS CCSA WATS LDN EMGTIE HPBusy DNDADM NANS OTRecall ICPTTF WAT SFX CCSAPA G E StartREC Mute Pattern 4 (b4=0, b5=0, b6=1) GST LDN EMGTIE BVBusy TRKSLATND NANS SCRecall SVCTF HWSFX ICPTPA G E StartREC Mute DDC Pattern 1 (b4=0, b5=0, b6=0) LDN EMGTIE DDCBusy TRKSLATND NANS SCRecall FRLTF Call Park(FX) (ICPT)PA G E StartREC Mute BV Pattern 4 (b4=0, b5=0, b6=1)