NEC Neax 2400 Ipx Office Data Specification

							NDA-24298 CHAPTER 4
Page 237
Issue 1
ASPAL : Assignment of Special Access Code for LDM
ASPAL:  Assignment of Special Access Code for LDM
1. General
This command determines the kind of service and the service Access Code to be executed on the Local Node
(LN) in the Fusion network.
2. Precautions
1. This command is used for the Business/Hotel (for Admin. station only) Application.
2. Use this command to assign the operator call and the priority call (terminating to ATT) in the FCCS
network.
3. Access Code for Telephone numbers may be programmed by this command, however, those Telephone
numbers are available in the self node only.
Telephone numbers available within the Fusion network are to be programmed at Network Control Node
(NCN) using the ANPDN and ASPAN commands.  For more details, see NEAX2400 IPX Fusion Network
System Manual.
4. The applicable Tenant Number (TN) range is designated by the ASYD command, SYS1, INDEX8. Enter
the tenant number this command affects.
If data for this command is common for all tenants (ASYDL command, SYS1, INDEX800, bit1=1), assign
TN parameter as data “1” for all tenants. 
						

							CHAPTER 4 NDA-24298
Page 238
Issue 1
ASPAL : Assignment of Special Access Code for LDM
3. Data Entry Instructions
Access code (Max. 6 digits)TENANT
NUMBER
(TN)ACCESS CODE
(ACC)
MAX. 6 DIGITSCONNECTION STATUS
INDEX
(CI) N/H/B  KIND OF
SERVICE 
(SRV)
ACC
CISRV
OGCA
LCR
N = Normal service
H = Hooking serviceSSC
OGCSSCA
TELNLCRS
PAGA ANNC
ANNCM
PAGC
B = Busy serviceNote: Telephone Number available in the self node only.
NND1 appears when SID=15.The number of ADC
(Abbreviation Digit Code) digits should be assigned in NND1.NND1
SERVICE INDEX
(SID) 1-63NECESSARY DIGIT
(NND) FUSION POINT CODE
(FPC)NECESSARY DIGIT FOR SPEED
CALLING (NND1) 1-24
SID
See Table 4-7When SRV=SSC (Service code) is assigned;
15 (Speed Calling-System;
     Access)
42 (Authorization Code/Forced
     Account Code/Pad Lock) 41 (Account Code Dial)
60 (Attendant Manual Override)
63 (Call Park ; Retrieve) NND appears when the following SID is entered.
NND data is variable depending on SIDNND
SID Number of digits for NNDAccess Code (1-24)
Access Code+Account 
code (1-15)
Access Code+Auth. code
(1-15)
Access Code (1-5)
Access Code (1-3)
2  (Dial Access to Attendant;
     Operator Call)
38 (Priority Call 2) 37 (Priority Call 1)
39 (Priority Call 3) FPC appears when the following SID is entered.FPC
SID Number of FPC1-253
1-253
1-253
1-253
= Outgoing call with route advance
= Least cost routing = Service code 
= Outgoing call = Service Code Appendix 
= Telephone Number Note= Register sender LCR 
= Paging Answer = Announcement Service 
= Announcement Service (Multiple Announcement)
= Paging Cancel
Note:This Telephone number is available to make a call and receive a call within the self node only.
If the Telephone number is to be used within the Fusion network, assign it at the Network Control Node
(NCN) using the ASPAN command. 
						

							NDA-24298 CHAPTER 4
Page 239
Issue 1
ASPAL : Assignment of Special Access Code for LDM
Note 1:
When Split Call Forwarding is in service (the command ASYDN, SYS1, INDEX79, bit2=1), this access code
is used for Split Call Forwarding service.  The access codes for Call Forwarding service are specified by
SRV = SSCA SIDA 86-89.
Note 2:The access code for the services marked * must be assigned with the same number of digit if the access
code begins using the same number. It is not available to assign different number of digit for the access
codes (i.e. access code “100” and “10” cannot coexist) in these services.
Table 4-7 SID (ASPAL)
SID SERVICE NAME SID SERVICE NAME
1 Call Hold 30-34 -
2 Dial Access to Attendant (Operator Call) 35* Call Pickup - Direct
3Call Back; Entry/
Camp on By Station36Hotel Service   Note 3
4 Executive Right of  Way 37* Priority Call 1
5 Call Waiting - Originating 38* Priority Call 2
6 Call Back; Cancel 39* Priority Call 3
7 Call Pickup 40 -
8*Call Forwarding - All Calls/Split Call Forwarding - 
All Calls (for trunk); Entry Note 141*Account Code Dial
9Call Forwarding - All Calls/Split Call Forwarding - 
All Calls (for trunk); Cancel Note 142*Authorization Code/Forced Account Code/Pad 
Lock; Set
10*Call Forwarding - Busy Line/Split Call Forwarding 
- Busy Line (for trunk); EntryNote 143Flash Signal Sending to Main office across CAS 
line
11Call Forwarding - Busy Line/Split Call Forwarding 
- Busy Line (for trunk); CancelNote 144Last Number Call
12*Call Forwarding - Don’t Answer/Split Call 
Forwarding - Don’t Answer (for trunk); Entry
Note 145-
13Call Forwarding - Don’t Answer/Split Call 
Forwarding - Don’t Answer (for trunk);
CancelNote 146Faulty Trunk Report
14* Speed Calling - Station; Entry 47 -
15* Speed Calling - System; Access 48 Timed Reminder/Automatic Wake-up; Entry
16 - 49 Timed Reminder/Automatic Wake-up; Cancel
17* Individual trunk access 50-55 -
18 - 56 Floor Service     Note 4
19 Out Going Trunk Queuing; Entry 57 Split Access (Same Number Access)Note 5
20 Out Going Trunk Queuing; Cancel 58, 59 Not used
21* Speed Calling - Station, Group; Access 60* Attendant Manual Override
22-27 - 61 Call Park; Entry 
						

							CHAPTER 4 NDA-24298
Page 240
Issue 1
ASPAL : Assignment of Special Access Code for LDM
Note 3:
When SRV = SSC (Service code), SID36 (Hotel Service) is assigned
For detailed information on Hotel Service, refer to the AASP command.
         STATE
(Hotel Service Code)
1 To be cleaned without ID code
2 Cleaning Completed without ID code
3 Ready for Occupancy without ID code
4 Use Not Allowed without ID code
 5-8 -
9 Maid Dial Answer Back without ID code-1
10 Maid Dial Answer Back without ID code-2
11 Maid Dial Answer Back without ID code-3
12 Maid Dial Answer Back without ID code-4
13 Maid Dial Answer Back without ID code-5
14 Maid Dial Answer Back without ID code-6
15 Maid Dial Answer Back without ID code-7
16 -
17 To be cleaned with ID code
18 Cleaning Completed with ID code
19 Ready for Occupancy with ID code
20 Use Not Allowed with ID code
21-24 -
25 Maid Dial Answer Back with ID code-1
26 Maid Dial Answer Back with ID code-2
27 Maid Dial Answer Back with ID code-3
28 Maid Dial Answer Back with ID code-4
29 Maid Dial Answer Back with ID code-5
30 Maid Dial Answer Back with ID code-6
31 Maid Dial Answer Back with ID code-7 
32 -
33 Automatic Wake Up Setting, Cancel; Same Special code
34 For Guest Station Secretary Telephone; Boss/Secretary Calling
35 Boss/Secretary Busy out; Set
36 Boss/Secretary Busy out; Cancel 
37  -
38 Automatic Wake-Up-Hotel Attendant Assistance Stop
39 Automatic Wake-Up-Hotel Attendant Assistance Stop Cancel
40 Alert Service Start (Hotel ATT)
41 Alert Service Stop (Hotel ATT)
42 Guest Service Telephone Screen Initialized
43 Guest Service Telephone Guest Room Information Retrieval
44 Direct Data Entry-Station (via Guest Station)
45 Alert Service Start (Special Admin. Station)
46 Alert Service Stop (Special Admin. Station)
47 -
48 2nd Wake-Up Call (Automatic) Set
49 2nd Wake-Up Call (Semi-Automatic) Set
50 2nd Wake-Up Call Cancel
51 Same Special Code Time Zone Connection Change
52 Same Special Code Time Zone Connection Change
53 Same Special Code Time Zone Connection Change
54 Same Special Code Time Zone Connection Change
55 Same Special Code Time Zone Connection Change
56-62 -
63 Dummy Number
Note: STATE=1-15 are used at the time of Maid ID Code Service is not provided;
           (ASYD SYS1 INDEX 164, bit3=0)
           STATE=17-31 are used at the time of Maid ID Code Service is provided;
           (ASYD SYS1 INDEX 164, bit3=1)
SERVICE INDEX
     (SID) 1-63
      STATE
36 
						

							NDA-24298 CHAPTER 4
Page 241
Issue 1
ASPAL : Assignment of Special Access Code for LDM
Note 4:
When SRV = SSC (Service code), SID56 (Floor Service) is assigned
Note 5:When SRV = SSC (Service code), SID57 (Split Access) is assigned
For detailed information on Hotel Service, refer to the AASP command.
SERVICE INDEX
    (SID) 1-63     NO.1
56
NO.1
(Kind of Assignment Number)
  Available numbers are 0-15.
  This data is used to assign Floor Service data by the ASPF
  command.
  Note: When programming Floor Service data, ASYD SYS1 
             INDEX 165, bit7=1 must have been assigned.
SERVICE INDEX
    (SID) 1-63NO.2KIND
57
NO.2
This parameter specifies the number (0-63) of the
access code being assigned for mutual access.
This parameter serves as a counter for the access
codes being assigned.
Note: This parameter is used when assigning the
           details of the service by the ASPS command.
KIND: (0-3)
This parameter specifies the Split Access Parameter Classification. The data to
be assigned here depends on how the Guest and Administration stations are
differentiated.
The Guest and Administration stations may be assigned to separate TNs, RSCs,
and/or SFCs, or they may only be differentiated by their respective designations
as Administration or Guest.
      0:    Administration/Guest
             (Assign this if the access code is to be shared between Guest
             and Administration with no correspondence to TN, RSC or SFC.)
      1:    TN
             (Assign this if the access code is to be shared among specified TNs)
      2:    RSC
             (Assign this if the access code is to be shared among specified RSCs)
      3:    SFC
             (Assign this if the access code is to be shared among specified SFCs) 
						

							CHAPTER 4 NDA-24298
Page 242
Issue 1
ASPAL : Assignment of Special Access Code for LDM
SERVICE INDEX  A (SIDA) 1-255
SIDA
When SRV=SSCA (Service Code Appendix) is assigned:   
Note 1 :For more detail information about Hotel Service, refer to the AASP command.
Note 2 : This data is valid for Call Forwarding service when Split Call Forwarding is in service (The 
command ASYD, SYS 1, INDEX 79, bit2=1.)
Note 3 : This data can be set when the Connection Status Index (CI) = Normal (N) since Release 5.
Note 4 : The access code for the services marked * on the table must be assigned with the same number of 
digit if the access code begins using the same number. It is not available to assign different number 
of digit for the access codes (i.e. access code 100  and 10 cannot coexist) in these Services.
1-40
41
42
43-45
46
47
48
49
50-52
53
54*
55*
56
64, 65
66-
Voice Call
Message Reminder (D
term)     
-
Line Load Control from ATTCON; Entry
Line Load Control from ATTCON; Cancel
Data Privacy on Demand; Entry     Note 3
Data Privacy on Demand; Cancel
-
Boss Secretary Override
Message Waiting Lamp Setting from
ATTCON; Set
Message Waiting Lamp Setting from
ATTCON; Cancel
Guest/Admin. Service                    Note 1
- 63 Call Pickup Expand 57-62 -
- Digital Announcement Card Multi-channel
Recording; Record
67
68*85*
86*
87*
88*
89
90
91
97* 92-96
99 -105
106
107
Digital Announcement Card Multi-channel
Recording; RetrieveCall Forwarding-All Calls; EntryNote 2 
Call Forwarding-Busy Line; EntryNote 2
Call Forwarding-Dont Answer; EntryNote 2
Call Forwarding-All Calls; CancelNote 2 
Call Forwarding-Busy Line; CancelNote 2
Call Forwarding-Dont Answer; Cancel
- 98Internal Zone Paging; Originate -
Call Hold Conference
Call Return
109 Number Sharing; Cancel
Call Block (restricts the dialed number); Entry
Call Block; Cancel 111
112
113
-
Call Trace 114, 115
116
- 117-255Call Block (restricts the last calling partys
number); Entry 110 --
108 Number Sharing; Entry
SIDA SIDAService Name Service Name
Pad Lock; Cancel
Note 2
NECESSARY DIGIT (NND) 1-6
NND appears when SIDA = 97 (Call Hold Conference).
The number of digits for an access code should be 
assigned NND.
69-84 -NND 
						

							NDA-24298 CHAPTER 4
Page 243
Issue 1
ASPAL : Assignment of Special Access Code for LDM
Assign the number of advanced trunk Route.LOGICAL ROUTE NUMBER
(LGRT)
Count
Assign a dummy route number.LGRT
Second dial tone sending (which is sent when a station has
dialed the digits specified in NND of the ANPDL command)
0 = Second DT is not sent
1 = Second DT is sent
2nd DTAuthorization code after dialing
ACC (LCR) + Destination number
0 = Out of Service
1 = In ServiceAH
ISDN-Sub Address Dialing
  0 = Out of Service
  1 = In ServiceSUB LOGICAL ROUTE
NUMBER (LGRT)SECOND DIAL TONE
(2nd DT) 0/1AUTHORIZATION CODE
(AH) 0/1SUB ADDRESS DIALING
(SUB) 0/1 Index counter (Count)
INDEXLOGICAL ROUTE NUMBER (LGRT)
When SRV = OGC (Outgoing call) is assigned
When SRV = OGCA (Outgoing call with route advance) is assigned
When SRV = LCR (Least cost routing) is assigned
When SRV = LCRS (Register sender LCR) is assigned
INDEX
INDEX is the route advance order.
1
2
3 
						

							CHAPTER 4 NDA-24298
Page 244
Issue 1
ASPAL : Assignment of Special Access Code for LDM
Note:
This Telephone Number is available to make a call and receive a call within the self node only. If the
Telephone Number is to be used within the Fusion Network, assign it at Network Control Node (NCN) using
the ASPAN command.
Assign the announce equipment number.
See Table 4-6.
When SRV=ANNC (Announcement service-Single announcement) is assigned
ANNOUNCEMENT EQUIPMENT NUMBER
(EQP) 0-127
EQP
Assign the tenant number of
the announcement trunk.
When SRV=ANNCM (Announcement service-Multiple announcement) is assigned
TN
TENANT NUMBER
(TN) 1-63
ANNOUNCEMENT EQUIPMENT NUMBER
(EQP) 122-125 
Assign the announcement equipment number with a
range from 122 to 125 (Multi announcement).
EQP
When SRV=PAGC (Paging Cancel) is assigned
When SRV=PAGA (Paging Answer) is assigned
LOGICAL ROUTE NUMBER
(LGRT) 1-899
LGRT
Enter the Logical Route Number
of Paging Trunk.
When SRV=TELN (Telephone Number)
MAXIMUM NUMBER OF DIGIT
(NND) 1-16 
						

							NDA-24298 CHAPTER 4
Page 245
Issue 1
ASPAL : Assignment of Special Access Code for LDM
4. Data Sheet
(a) Service Code (SRV = SSC)
Note 1:The parameter may vary depending on the service.
Note 2:When Split Call Forwarding is in service (the command ASYD, SYS1, INDEX79, bit2=1), this access code
is used for Split Call Forwarding.
Note 3:When Speed Calling-System; Access  is assigned, NND1 parameter assignment is  required in addition to
the NND parameter.
Note 4:Fill in the FPC in place of the parameter NND.
TENANT
NUMBER 
(TN)ACCESS CODE
(ACC)
MAXIMUM
6 DIGITSCONNECTION 
STATUS INDEX
(CI) N/H/BKIND OF
SERVICE 
(SRV)SERVICE
FEATURE
INDEX
(SID) 1–63NUMBER OF 
NECESSARY
 DIGITS
(NND) Note 1SERVICE CONTENTS
H Hooking SSC 1Call Hold
NNormal
SSC 2Dial Access to Attendant 
(Operator Call) Note 4
H Hooking
BBusy
SSC 3
Call Back; Entry
H Hooking
Camp on By Station
BBusy SSC 4
Executive Right of Way
NNormal
SSC 5
Call Waiting – Originating
BBusy
NNormal SSC 6
Call Back; Cancel
7Not used
NNormal
SSC 8
C.F. – All Calls/Split C.F. – 
All Calls; EntryNote 2
NNormal
SSC 9
C.F. – All Calls/Split C.F. – 
All Calls; CancelNote 2
NNormal
SSC 10
C.F. – Busy Line/Split C.F. 
– 
Busy Line; Entry Note 2
NNormal
SSC 11
C.F. – Busy Line/Split C.F. 
– 
Busy Line; Cancel 
Note 2
NNormal
SSC 12
C.F. – Don’t Answer/Split 
C.F.
 – Don’t Answer; Entry
Note 2
NNormal
SSC 13
C.F. – Don’t Answer/Split 
C.F.
 – Don’t Answer;  
CancelNote 2
NNormal
SSC 14
Speed Calling – Station; 
Entry
NNormal
SSC 15Speed Calling
 – System;
AccessNote 3
16Not used
N Normal SSC 17
Individual Trunk Access
18Not used 
						

							CHAPTER 4 NDA-24298
Page 246
Issue 1
ASPAL : Assignment of Special Access Code for LDM
(a) Service code (SRV = SSC) (Continued)
Note 1:The parameter may vary depending on the service.
Note 2:The available numbers of necessary digits vary depending on the parameter SID.
Note 3:For more detail information about Hotel Service, refer to the AASP command.
Note 4:Fill in the FPC in place of the parameter NND.
TENANT
NUMBER 
(TN)ACCESS CODE
(ACC)
MAXIMUM
6 DIGITSCONNECTION 
STATUS INDEX
(CI) N/H/BKIND OF
SERVICE 
(SRV)SERVICE
FEATURE
INDEX
(SID) 1–63NUMBER OF 
NECESSARY 
DIGITS
(NND)
Note 1, Note 2SERVICE CONTENTS
B Busy SSC 19OG Trunk Queuing; Entry
N Normal SSC 20
OG Trunk Queuing; Cancel
N Normal SSC 21
Speed Calling – Station, 
Group; Access
22
27Not used
N Normal SSC 28
Call Forwarding I’m Here; 
Set
N Normal SSC 29
Call Forwarding I’m Here; 
Cancel
30
34Not used
N Normal SSC 35
Call Pickup – Direct
N Normal SSC 36
Hotel ServiceNote 3
NNormal
SSC 37Priority Call 1Note 4
H Hooking
NNormal
SSC 38Priority Call 2Note 4
H Hooking
NNormal
SSC 39Priority Call 3Note 4
H Hooking
40Not used
NNormal
SSC 41Account Code Dial
H Hooking
NNormal
SSC 42Authorization Code/Forced 
Account Code/Pad Lock; Set
H Hooking
H Hooking SSC 43
Flash Signal Sending to 
Main office across CAS Line
N Normal SSC 44
Last Number Call
45Not Used
H Hooking SSC 46
Faulty Trunk Report
~
~