Home > NEC > Communications System > NEC Neax 2400 Ipx Office Data Specification

NEC Neax 2400 Ipx Office Data Specification

Add to Favourites
    Download as PDF Print this page Share this page

    Have a look at the manual NEC Neax 2400 Ipx Office Data Specification online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1168 NEC manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    View all the pages
    Page
    of 1020
    Add page 811 to Favourites
    image text
    Enable zoom 
    							NDA-24298 CHAPTER 4
Page 777
Issue 1
AAND : Assignment of Automatic Number Identification Data
(c) When ATT, the Individual Attendant Number, is not assigned. Outgoing (AT = 1). 
ROUTE
NUMBER
(RT)STA
OUTGOING/ATT
OUTGOING
(AT)OFFICE CODE
(DC)
MAXIMUM 10 DIGITSREMARKS
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
    Add page 812 to Favourites
    image text
    Enable zoom 
    							CHAPTER 4 NDA-24298
Page 778
Issue 1
AAND_LR : Assignment of Automatic Number Identification Data – Logical Route Number
AAND_LR: Assignment of Automatic Number Identification Data – Logical 
Route Number
1. General
This command is used to assign ANI data for the number of digits of calling station number and the office code
on each tenant basis for the Automatic Number Identification (ANI) service (for E911 ANI). Route number of
the AAND command can be assigned by using Logical Route.
2. Precautions
1. Prior to this command, logical route data must be allocated by using the ALRTN command.
2. Only when logging in to the NCN (Network Control Node), this command can be used to assign the
logical route data of self-Node and the other Nodes in the Fusion Network. If logging in to a LN (Local
Node), data setting only for the self-node is available. (Error message is indicated if you try to write the
data of other Node.)
3. The Route number of RT parameter should have been designated in ARTD, CDN19 ANI = 1.
3. Data Entry Instructions
Office Code for the number of digits 
assigned to parameter ADD.
MAIN/
SATELLITE 
CENTRAL 
(CC)EXPANSION 
OF STA 
NUMBER 
LENGTH
 (KT)
OFF/ON LOGICAL 
ROUTE 
NUMBER 
(LGRT)
1-899FUSION POINT 
CODE
(FPC)
1-253OUTSIDE 
ROUTE 
NUMBER
(RT)
1-STA/ATT 
OUTGOING
(AT)
AT
DC • STA outgoing
• ATT outgoing
These parameters vary depending on the 
assignment of the previous parameter.
STA 
NUMBER 
LENGTH 
(STNL) 
1-8OFFICE
CODE TO BE 
ADDED
(ADD)
1-10CALL 
ORIGINATOR 
DIGIT TO BE 
SKIPPED
 (SKIP)
0-10OFFICE CODE
 (DC) 
MAX. 10 DIGITS
[0-9, *, #]
CC
• Main Central
• Satellite Central
CENTRAL OFFICE 
CODE 
(COC) 
MAX. 5 DIGITS
    Add page 813 to Favourites
    image text
    Enable zoom 
    							NDA-24298 CHAPTER 4
Page 779
Issue 1
AAND_LR : Assignment of Automatic Number Identification Data – Logical Route Number
4. Data Sheet
(a) When AT = STA outgoing, CC = Main Central is selected;
 
Note:This parameter can be assigned when “KT = ON.”
LOGICAL 
ROUTE 
NUMBER 
(LGRT)
1-899FUSION 
POINT 
CODE
(FPC)
1-253OUTSIDE 
ROUTE 
NUMBER 
(RT)
1-STA/ATT
OUTGOING
(AT)MAIN/
SATELLITE 
CENTRAL
 (CC)EXPANSION
 OF STA
NUMBER 
LENGTH 
(KT)
OFF/ONSTA
NUMBER 
LENGTH 
(STNL)
1– 8
NoteOFFICE 
CODE 
TO  B E  
ADDED 
(ADD)
1–10CALL
ORIGINATOR
 DIGIT TO BE 
SKIPPED 
(SKIP)
0–10OFFICE CODE 
(DC)
MAX. 10 DIGITS
[0-9, *, #]
    Add page 814 to Favourites
    image text
    Enable zoom 
    							CHAPTER 4 NDA-24298
Page 780
Issue 1
AAND_LR : Assignment of Automatic Number Identification Data – Logical Route Number
(b) When AT = STA, CC = Satellite Central is selected;
LOGICAL 
ROUTE 
NUMBER 
(LGRT)
1-899FUSION 
POINT 
CODE
(FPC)
1-253OUTSIDE 
ROUTE 
NUMBER 
(RT)
1-STA/ATT
OUTGOING
(AT)MAIN/
SATELLITE 
CENTRAL
 (CC)CENTRAL OFFICE 
CODE
(COC)
MAX. 5 DIGITSOFFICE 
CODE 
TO B E 
ADDED 
(ADD)
1–10CALL
ORIGINATOR
 DIGIT TO BE 
SKIPPED 
(SKIP)
0–10OFFICE CODE 
(DC)
MAX. 10 DIGITS
[0-9, *, #]
    Add page 815 to Favourites
    image text
    Enable zoom 
    							NDA-24298 CHAPTER 4
Page 781
Issue 1
AAND_LR : Assignment of Automatic Number Identification Data – Logical Route Number
(c) When AT = ATT outgoing is selected; 
LOGICAL 
ROUTE 
NUMBER 
(LGRT)
1-899FUSION 
POINT CODE
(FPC)
1-253OUTSIDE 
ROUTE 
NUMBER 
(RT)
1-STA/ATT
OUTGOING
(AT)OFFICE CODE 
(DC)
MAX. 10 DIGITS
[0-9, *, #]REMARKS
    Add page 816 to Favourites
    image text
    Enable zoom 
    							CHAPTER 4 NDA-24298
Page 782
Issue 1
AANDE : Assignment of Automatic Number Identification Expansion Data
AANDE: Assignment of Automatic Number Identification Expansion Data
1. General
This command assigns ANI data for the number of digits for the calling station number and the office code on
each tenant basis for the Automatic Number Identification Expansion (ANIE) Service. (For E911ANI)
2. Precautions
1. This data is available when E911 ANI Office Code Expansion is in service (the ASYD command, SYS 1,
INDEX 246, bit5=1).
2.  The applicable Tenant Number (TN) range is designated by the ASYD command, SYS 1, INDEX 8. 
3. Data Entry Instructions
NUMBER
    (TN)TENANT      CALL
ORIGINATOR
      DIGIT
  (SKIP) 0-10OFFICE CODE
TO BE ADDED
       (ADD)
        1-10OFFICE CODE (DC)
    MAX.10 DIGITS
SKIP
Enter the number of digits skipped
from the original office code.
The office code number to be added.DC
ADD
Enter the number of digits added
to the original office code.
    Add page 817 to Favourites
    image text
    Enable zoom 
    							NDA-24298 CHAPTER 4
Page 783
Issue 1
AANDE : Assignment of Automatic Number Identification Expansion Data
4. Data Sheet
TENANT
NUMBER
(TN)CALL
ORIGINATOR
(SKIP)
0 - 10OFFICE CODE
TO BE ADDED
(ADD)
1 - 10OFFICE CODE 
(DC)
MAX. 10 DIGITS
    Add page 818 to Favourites
    image text
    Enable zoom 
    							CHAPTER 4 NDA-24298
Page 784
Issue 1
AANI : Assignment of ANI Data
AANI: Assignment of ANI Data
1. General
This command assigns Automatic Number Identification (ANI) data sent per tenant by the request from opposite
office.
2. Precautions
1. Before using this command, ASYD SYS1 INDEX 125 b4 - b7 (Type of MFC Signaling System) should
be assigned. 
2. When ASYD command, SYS 2 INDEX 15, b2 = 1, the following number is sent as ANI data.
(a) Calling party is a station:
Calling party’s station number is sent. 
(b) Calling party is an Attendant or tandem connection:
LDN assigned in this command is sent.
If b2 = 0, LDN assigned in this command is sent.
3. The ANI parameter of ARTD command should be assigned prior to this command.
4. The applicable Tenant Number (TN) range is designated by the ASYD command, SYS 1, INDEX 8.
3. Data Entry Instructions
NUMBER
    (TN)TENANTCALL NUMBER OF TOLL
                 (TS)
    MAXIMUM 8 DIGITSLISTED DIRECTORY
    NUMBER (LDN)
 MAXIMUM 8 DIGITS
If no LS (Local Number) of ANI is required,
enter * or # in this parameter.
The LS is not included in ANI.LS
CALL NUMBER OF LOCAL                 (LS)
    MAXIMUM 8 DIGITSREMARKS
TS
This paramenter is not used. (For China only)
Press SPACE key and Enter key in order to skip
this parameter.
    Add page 819 to Favourites
    image text
    Enable zoom 
    							NDA-24298 CHAPTER 4
Page 785
Issue 1
AANI : Assignment of ANI Data
4. Data Sheet
TENANT
NUMBER
(TN)CALL NUMBER OF TOLL
(TS)
MAXIMUM 8 DIGITSCALL NUMBER OF LOCAL
(LS)
MAXIMUM 8 DIGITSLISTED DIRECTORY
NUMBER 
(LDN)
MAXIMUM 8 DIGITS
    Add page 820 to Favourites
    image text
    Enable zoom 
    							CHAPTER 4 NDA-24298
Page 786
Issue 1
ASPD : Assignment of Speed Calling
ASPD: Assignment of Speed Calling 
1. General
This command assigns the speed calling number corresponding to each Abbreviated Digit Code (ADC). 
2. Precautions
1. The speed calling number assigned by this command (the data entered at the DC parameter) is transmitted
when an ADC is dialed following the Speed Calling - System access code. 
2. The following command should be assigned to accomplish the Speed Calling - System service feature:
ASPA command, SSC = 15 ASFC command, SFI = 12
3. The Speed Calling - System data may also be used in conjunction with the following commands, and the
ADC parameter is an intermediate data to correspond to them:
AABD: The restriction data of Speed Calling - System 
ACFO: System Call Forwarding data
ACSA: Ring down trunk incoming call termination (Day mode)
ACSI: Ring down trunk incoming call termination (Day and Night mode, or Night mode)
AFCP: Calling Party Recognition Service of ISDN.
AHLS: Hot Line
ALDN: LDN diversion of DID call
4. The applicable Tenant Number (TN) range is designated by the ASYD command, SYS 1, INDEX 8. If
data for this command is common for all tenants (ASYD command, SYS1, INDEX 93, bit3=1), assign TN
parameter as data “1” for all tenants.
5. The access code for the designated outgoing trunk route should be included in the speed calling number to
be assigned in the DC parameter.
6. If a pause is required within the speed calling number, enter “P” between the desired digits in the CD
parameter. The default pause is 3 seconds and can be adjusted using the ASYD command, SYS1,
INDEX131.
7. When assigning a speed calling number in which certain digits vary, enter “M” where digits are to be
dialed manually. It should be noted that once “M” is entered in any part of telephone number, all digits
following the “M” must be dialed manually.
    All NEC manuals Comments (0)

    Related Manuals for NEC Neax 2400 Ipx Office Data Specification