NEC Neax 2400 Ipx Office Data Specification
Have a look at the manual NEC Neax 2400 Ipx Office Data Specification online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1168 NEC manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
NDA-24298 CHAPTER 4 Page 467 Issue 1 ADSL : Assignment of Dterm Soft Key on LCD 5. After system initialization is performed, the soft key cannot be used for a minute. 6. When the soft key data is set on a system basis, SKP = 0 is assigned by this command. 7. The priority order for displaying the data in the function key area (the third line or the lowest line) is as follows. 8. The LCD display is not changed for a minute, after if the soft key data is assigned to all stations in a system using this command or the characters for the LCD display are changed using the AFDD command. 9. When the soft key data is programmed for the busy station, the LCD display does not change until the station becomes idle. 10. The same function data (FKY) can not be assigned to both soft key and function key. 11. The created soft key pattern, which is assigned at SKP=0, is applied to a D term Series E by designating the programmed SKP number in ADKS. As for the key pattern data in SKP=0, ADKS is not necessary. If SKP=0 is designated in ADKS, default key pattern data (refer to Table 4-12) is applied to the D term. Priority orderDisplayed Data Description 1Services set to the func- tion key dataThe application service that is set to the function key 2Services set to the func- tion key dataOnly when the station is idle/originating and the service set to the function key 3Soft key assigned via function keyWhen the soft key data is in the middle of being set via the function key (FKY=122) 4(a)Soft key data used on a station basisThe soft key data assigned via the ADSL (SKP=0) and ADKS command. (b)Soft key used on a system basisThe soft key data is assigned via the ADSL (SKP=0). (c)Default soft key data by ROM dataDefault soft key data (a) or (b) data shown above is not programmed.
CHAPTER 4 NDA-24298
Page 468
Issue 1
ADSL : Assignment of Dterm Soft Key on LCD
3. Data Entry Instructions
DISP
DISP
SOFT KEY PATTERN(SKP) 0-15STATUS NUMBER(SN) 0-15FUNCTION KEY DATA(FKY) 1-320
26 12
2
31
The soft key indication is
displayed when DISP has assigned
by the AFDD command.
SN
SKN
Soft key number (SKN)
appears on the MAT.SKP
Assign arbitrary
number within 0
through 15.
0=soft key pattern
shared in a system
1-15=soft key
pattern alloted
to each station.
SKN0-15
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23-25
26
27-47
48
49
50
51
52-54
55
56
57-59
60
61-82
83
84Call Forwarding-Busy Line
Call Forwarding-All Calls
Executive Right of Way
Call Waiting
Call Back
-
Save and Repeat
-
Boss-Secretary-Message
Waiting Lamp Control; Set
Call Hold
Boss-Secretary-Message
Waiting Lamp Control; Cancel
Call Pickup-Group
Three-way Calling
Voice Call
Speed Calling-System
-
CAS SHF
-
UCD Busy Out
-
Flash Button
Call Forwarding-Dont Answer
-
Speed Calling-Station
-
Privacy Release
-
Do Not Disturb
Microphone
-
PAGE
OFF/ON Hook for Headset
-
Manual Signaling Key
-
Retain Conference
Serial CallFDB
FDA
E_OVR
CW
CB
-
S&R
-
MW SET
C_HOLD
MWOFF
PICK
CONF
VOICE
S-SPD
-
CAS
-
UCDBO
-
FLASH
FDN
-
G_SPD
-
P-RLS
-
DND
MIC
-
BPAGE
-
SIG
-
CKEEP
SCALL FKY Service name Default displayFKY Service name Default display
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102-112
113
114
115
116
117
118-119
120
121
122
123
124
125
126
127
128
129
130
131
132~320Internal Zone Paging
-
Wake Up Set
Wake Up Reset
Do Not Disturb Set
Do Not Disturb Reset
Room Cut Off Set
Room Cut Off Reset
Message Waiting Set
Message Waiting Reset
Check In
Check Out
Status
Audit
Enter
Clear Enter
END
-
Call ID change display
-
Call pickup expand
-
Ringer mute
-
Next page of soft keys
(Scroll key)
Previous page of soft keys
(Back Scroll key)
-
Off Hook Ringing
MUTE
Head Set Note 1
PS Key
Boss Move
Call Block
Call Trace
-
Disconnect
-IZP
-
WUS
WUR
DDS
DDR
RCS
RCR
MWS
MWR
C/I
C/O
STS
AUD
ENT
E
END
-
IDCHG
-
GPICK
-
RMUTE
-
>>>
NDA-24298 CHAPTER 4 Page 469 Issue 1 ADSL : Assignment of Dterm Soft Key on LCD 4. Data Sheet SOFT KEY PAT T E R N (SKP)STATUS NUMBER (SN)SKNFUNCTION KEY DATA (FKY)DISP REMARKS 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
CHAPTER 4 NDA-24298 Page 470 Issue 1 ADKS : Assignment of Dterm Key Status Data ADKS: Assignment of Dterm Key Status Data 1. General This command assigns the soft key pattern (which is assigned by the ADSL command) onto a D term Series E. Additionally, Line/Feature button and DSS key arrangement on the Dterm Series E can be specified. 2. Precautions 1. Four soft keys appear on a D term Series E as shown in Figure 4-13. The function of the soft key varies depending on the status and current functions involved which are displayed on the bottom line of LCD. Figure 4-13 Dterm Series E Key Arrangement 2. Four different pages are prepared on the soft key for one status, and a station user can go into the next page by pressing >>> soft key. (Instead of >>> key, the page scroll key can be programmed on a Line/Feature button of D term Series E.) 3. The character appearance on each soft key function can be modified by the AFDD command. 1 2 3 4 5 6 7 8 9 0 # NEC 16 5 4 3 2 712 11 10 9 8 1318 17 16 15 14 1924 23 26 25 28 27 30 29 32 31 22 21 20 FeatureHelp Exit Recall Conf Redial Speaker Answer Transfer Hold Soft keys
NDA-24298 CHAPTER 4 Page 471 Issue 1 ADKS : Assignment of Dterm Key Status Data 4. The default key pattern (SKP = 0) of the soft keys are listed in the table below. When data 1 through 15 is assigned in the SKP parameter, the ADSL command must be assigned to specify the soft key pattern (SKP). Table 4-18 Default Key Pattern STATUS PAGE PG=0 PG=1 Idle0 MIC DND >>> MIC DND 1 2 3 Originating (DT connection)0 MIC PICK FDA >>> MIC PICK FDA FDN 1 FDN FDB >>> FDB 2 3 Originating (RBT connection)0 MIC VOICE >>> MIC VOICE 1 2 3 Called station busy (BT connection)0 MIC CB CW >>> MIC CB CW S&R 1S&R 2 3 Communication in progress (Converse)0 MIC DND >>> MIC DND 1 2 3 Consultation Hold (SPDT connection)0 MIC CONF >>> MIC CONF 1 2 3 Trunk busy (BT connection)0 MIC >>> MIC 1 2 3 Consultation Hold when Called Station is Busy- Controlling Station0 MIC CB FLASH MIC CB FLASH 1 2 3
CHAPTER 4 NDA-24298 Page 472 Issue 1 ADKS : Assignment of Dterm Key Status Data 3-Party Conference0 MIC >>> MIC 1 2 3 Others0 MIC >>> MIC 1 2 3Table 4-18 Default Key Pattern (Continued) STATUS PAGE PG=0 PG=1
NDA-24298 CHAPTER 4
Page 473
Issue 1
ADKS : Assignment of Dterm Key Status Data
5. Three different kinds of Line/Feature buttons and DSS key arrangements can be specified by LKP
parameter.
Figure 4-14 Line/Feature Button and DSS Key Arrangement on Dterm Series E
EXITHELP
16
12
32 5 4 3 2
5118 7 6
18 91712 11 10
24 13 23
26 25
28 27
30 29
31 16 15 14
LKP=1 (16 Line/Feature buttons + 16DSS keys)
EXITHELP
16
12
32 5 4 3 2
71110 9 8
18 13 1716 15 14
24 19 23
26 25
28 27
30 29
31 22 21 20
LKP=2 (24 Line/Feature buttons + 8DSS keys)
EXITHELP
16
12
32 5 4 3 2
71110 9 8
18 13 1716 15 14
24 19 23
26 25
28 27
30 29
31 22 21 20
LKP=3 (32 Line/Feature buttons)Line/Feature buttons number
Line/Feature buttons number
Line/Feature buttons number
Note : Line/Feature button function is assigned
by the AKYD command.
CHAPTER 4 NDA-24298 Page 474 Issue 1 ADKS : Assignment of Dterm Key Status Data 3. Data Entry Instructions 1 2 5 6 4 5 0 1 0 Select a Line/Feature button and DSS key arrangement 1 = 16 Line/Feature buttons + 16 DSS keys 2 = 24 Line/Feature buttons + 8 DSS keys 3 = 32 Line/Feature LKP Page change key allocation (Refer to [Precaution]) 0 = Page change key appears on a soft key(>>>) 1 = Page change key disappears on a soft key.PG STATION NUMBER (STN)SOFT KEY PATTERN DATA (SKP)KEY PATTERN DATA (LKP)LCD PAGE (PG) TENANT NUMBER (TN) 0 = Default pattern as shown on [Precaution (4)] 1-15 = SKP assigned by the ADSL commandSKP
NDA-24298 CHAPTER 4 Page 475 Issue 1 ADKS : Assignment of Dterm Key Status Data 4. Data Sheet TENANT NUMBER (TN)STATION NUMBER (STA)SOFT KEY PATTERN DATA (SKP)LINE KEY PATTERN DATA (LKP)LCD PAGE (PG)
CHAPTER 4 NDA-24298 Page 476 Issue 1 ADRTL : Assignment of Dterm Display Route Data for LDM ADRTL: Assignment of Dterm Display Route Data for LDM 1. General This command changes the display of trunk class information on the D term instead of the Trunk Class (TCL) designation of the ARTD command. 2. Precautions 1. The data assigned in this command affects the stand alone-node and Local Node (LN). 2. When this data is assigned to Local Data Memory (LDM) in the Fusion Network, if Network Data Memory (NDM) has Display Route Data designated by the ADRTN commands, NDM data overrides LDM data. 3. The data assigned by this command is not available for ISDN stations and PS. 4. When a call terminated from the trunk COC number has been assigned by the ACOC command, the following is displayed on the D term as to “TYPE” parameter; TYPE = 1 (4 characters) is entered, both COC number assigned by the ACOC command and 4- character trunk class assigned at “DISP” parameter is displayed. TYPE = 2 (8 characters) is entered, only the 8-character trunk class assigned at “DISP” parameter is displayed. 3. Data Entry Instructions The maximum number of characters 1 = 4 (4 bytes ASCII characters) 2 = 8 (8 bytes ASCII characters)TYPE Assign Physical Route number at the non-Fusion node.RT Route Number (RT)Character Display Type (TYPE) 1, 2Display for Trunk Class on Dterm (DISP)REMARKS The characters displayed on the Dterm. DISP Note:For Fusion node, assign Logical Route number using the ADRTN command.