NEC Neax 2400 Ipx Office Data Specification
Have a look at the manual NEC Neax 2400 Ipx Office Data Specification online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1168 NEC manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
NDA-24298 CHAPTER 4
Page 377
Issue 1
ATDPL : Assignment of Toll Code Restriction Data for LDM
If data is set as follows, a toll call can be restricted by developing NPA - Nxx.
At Toll Code Restriction Data for LDM (ATDPL)
DC = 9-1, TDI = 2, NND = 6 (NPA - Nxx)
At Area & Office Code Data (AARPL)
DC = NAP - Nxx (6 digits)
4. Data can be entered on a Day/Night basis, if specified in ASYD command, SYS 1, INDEX 75, Bit 3=1.
3. Data Entry Instructions
NND
This parameter is
available only when
TDI=2
DAY/NIGHT
MODE
(DAY/NIGHT)ROUTE
RESTRICTION
NUMBER
(RSC) 0-15OUTGOING
LOGICAL ROUTE
NUMBER
(OGLGRT) 1-899DESTINATION (AREA) CODE
(DC)
MAX. 11 DIGITSNECESSARY
DIGIT
(NND)
1-12 RESTRICTION
DATA
(TDI)
0-3
Outgoing Connection
DAY/NIGHT
D = Day Mode
N = Night Mode
TDI
0 = Connection is Restricted
1 = Connection is Allowed
2 = 3/6 Digit Toll Restriction
3 = C.O. Operator Call (9+0)
When assigning DC, the digits including
the access code must be assigned.Refer to the ARSCN command.
CHAPTER 4 NDA-24298 Page 378 Issue 1 ATDPL : Assignment of Toll Code Restriction Data for LDM 4. Data Sheet DAY /N IG HT MODE (DAY/NIGHT) D/NROUTE RESTRICTION NUMBER (RSC) 0-15OUTGOING LOGICAL ROUTE NUMBER (OGLGRT) 1-899DESTINATION (AREA) CODE (DC) MAX. 11 DIGITSRESTRICTION DATA (TDI) 0-3NECESSARY DIGIT (NND) 1-12
NDA-24298 CHAPTER 4 Page 379 Issue 1 ATDPN : Assignment of Toll Code Restriction Data for NDM ATDPN: Assignment of Toll Code Restriction Data for NDM 1. General This command assigns the area code of Toll Restriction - 3/6 digits for both an outgoing connection and a tandem connection. This data is written in the Network Data Memory (NDM) of the Network Control Node (NCN). The data assigned by this command is used in common within the Fusion Network. 2. Precautions 1. This command is used when restriction data is assigned to RES = 2 (Toll Restriction is required) in the ARSCN command or in the ARRCN command. 2. The office code following the area code assigned on this command can also be specified by the AARPN command. 3. Setting Method of Area and Office Code Restriction In case the number to be dialed is as shown above. (a) 3-Digit Toll Restriction 9 - 1 - NPA - Nxx - xxxx A 3-digit toll restriction is a restriction that is to be executed by developing the contents (NPA in this case) of the digits that follow the toll code. If the data is set as follows, a toll call can be restricted by developing NPA. At Toll Code Restriction Data (ATDPN) DC = 9-1, TDI = 2, NND = 3 (NPA) At Area & Office Code Data (AARPN) DC = NPA (Only 3 digits) (b) 6-Digit Toll Restriction 9 - 1 - NPA - Nxx - xxxx A 6-digit toll restriction is a restriction that is to be executed by developing the contents (NPA - Nxx in this case) of the 6 digits that follow the toll code. TRK AC C CODETOLL CODEAREA CODEOFFICE CODESTATION NUMBER 9–1–NPA–Nxx–xxxx
CHAPTER 4 NDA-24298 Page 380 Issue 1 ATDPN : Assignment of Toll Code Restriction Data for NDM If data is set as follows, a toll call can be restricted by developing NPA - Nxx. At Toll Code Restriction Data (ATDPN) DC = 9-1, TDI = 2, NND = 6 (NPA - Nxx) At Area & Office Code Data (AARPN) DC = NAP - Nxx (6 digits) 4. Data can be entered on a Day/Night basis, if specified by the ASYDN command, SYS 1, INDEX 75, Bit 3 = 1. 5. The rest of the parameter appearance depends on the data entered in TDM/OG parameter.
NDA-24298 CHAPTER 4
Page 381
Issue 1
ATDPN : Assignment of Toll Code Restriction Data for NDM
3. Data Entry Instructions
Tandem Switching
TANDEM/
OUTGOING
CONNECTION
(TDM/OG)DAY/NIGHT
MODE
(DAY/NIGHT)INCOMING
LOGICAL
ROUTE
NUMBER
(ICLGRT)
1-899OUTGOING
LOGICAL
ROUTE
NUMBER
(OGLGRT)
1-899
RESTRICTION
CLASS
(RSC)
0-15OUTGOING
LOGICAL
ROUTE
NUMBER
(OGLGRT)
1-899
DESTINATION (AREA) CODE
(DC)
MAX. 11 DIGITSNECESSARY
DIGIT
(NND)
1-12 RESTRICTION
DATA
(TDI)
0-3
T = Tandem Connection
O = Outgoing Connection TDM/OG
DAY/NIGHT
D = Day Mode
N = Night Mode
TDI
Restriction Data
0 = Connection is Restricted
1 = Connection is Allowed
2 = 3/6 Digit Toll Restriction
3 = C.O. Operator Call (9+0)
When assigning DC, the digits including
the access code must be assigned.
NND
This parameter is
available only when
TDI=2
NND
This parameter is
available only when
TDI=2
T
TANDEM/
OUTGOING
CONNECTION
(TDM/OG)DAY/NIGHT
MODE
(DAY/NIGHT)DESTINATION (AREA) CODE
(DC)
MAX. 11 DIGITSNECESSARY
DIGIT
(NND)
1-12 RESTRICTION
DATA
(TDI)
0-3
O Outgoing Connection
T = Tandem Connection
O = Outgoing Connection TDM/OG
DAY/NIGHT
D = Day Mode
N = Night Mode
TDI
0 = Connection is Restricted
1 = Connection is Allowed
2 = 3/6 Digit Toll Restriction
3 = C.O. Operator Call (9+0)
When assigning DC, the digits including
the access code must be assigned.Refer to the ARSCN command.
CHAPTER 4 NDA-24298 Page 382 Issue 1 ATDPN : Assignment of Toll Code Restriction Data for NDM 4. Data Sheet (a) Tandem Connection (TDM/OG = T) TANDEM/ OUTGOING T/ODAY/NIGHT MODE (DAY/NIGHT) D/NINCOMING LOGICAL ROUTE NUMBER (ICLGRT) 1-899OUTGOING LOGICAL ROUTE NUMBER (OGLGRT) 1-899DESTINATION (AREA) CODE (DC) MAXIMUM 11 DIGITSRESTRICTION DATA (TDI) 0-3NECESSARY DIGIT (NND) 1-12 T
NDA-24298 CHAPTER 4 Page 383 Issue 1 ATDPN : Assignment of Toll Code Restriction Data for NDM (b) Outgoing Connection (TDM/OG = O) TANDEM/ OUTGOING (TDM/OG)DAY/NIGHT MODE (DAY/NIGHT) D/NROUTE RESTRICTION NUMBER (RSC) 0-15OUTGOING LOGICAL ROUTE NUMBER (OGLGRT) 1-899DESTINATION (AREA) CODE (DC) MAX. 11 DIGITSRESTRICTION DATA (TDI) 0-3NECESSARY DIGIT (NND) 1-12 O
CHAPTER 4 NDA-24298 Page 384 Issue 1 AARP : Assignment of Area Code Restriction AARP: Assignment of Area Code Restriction 1. General This command assigns the area/office code of Toll Restriction - 3/6 digits in conjunction with ATDP command. 2. Precautions 1. This command is used when restriction data is assigned to RES E 2 (Toll Restriction is required) in the ARSC command or in the ARRC command. 3. Data Entry Instructions Note:In case the data has already been assigned when “Get” button is executed after checking “6 Digits” parameter and entering DC E 000000, “Del” button is not valid while “Set” button is to be effective. Then the Restriction data can be changed (overwritten) by “Set” button. OUTGOING ROUTE NUMBER (OGRT)ROUTE RESTRICTION CLASS (RSC) 0-15FLAG OF 3 OR 6 DIGITS (FLAG) 3 Digits/6 DigitsDESTINATION (AREA/OFFICE) CODE (DC) MAX. 6 DIGITSRESTRICTION DATA (RES) 0/1REMARKS FLAG Select either 3 Digits or 6 Digits check box. RES 0 = Area/Office code is restricted. 1 = Area/Office code is allowed. DC should not include the access code.DCRSC assigned by the ARSC command.RSC
NDA-24298 CHAPTER 4 Page 385 Issue 1 AARP : Assignment of Area Code Restriction 4. Data Sheet OUTGOING ROUTE NUMBER (OGRT)ROUTE RESTRICTION CLASS (RSC) 0 -15FLAG OF 3 OR 6 DIGITS (FLAG) 3 Digits/6 DigitsDESTINATION (AREA/OFFICE) CODE (DC) MAX. 6 DIGITSRESTRICTION DATA (RES) 0/1REMARKS
CHAPTER 4 NDA-24298 Page 386 Issue 1 AARPL : Assignment of Area Code Restriction for LDM AARPL: Assignment of Area Code Restriction for LDM 1. General This command assigns the area/office code of Toll Restriction - 3/6 digits for Fusion service in conjunction with ATDPL (for LDM)/ATDPN (for NDM) command. This data is written in Local Data Memory (LDM). When common data is needed in the Fusion Network, assign the data by the AARPN command. 2. Precautions 1. This command is used when restriction data is assigned to RES E 2 (Toll Restriction is required) in the ARSCN (NDM) command or in the ARRCN command. 3. Data Entry Instructions Note:In case the data has already been assigned when “Get” button is executed after checking “6 Digits” parameter and entering DC E 000000, “Del” button is not valid while “Set” button is to be effective. Then the Restriction data can be changed (overwritten) by “Set” button. OUTGOING LOGICAL ROUTE NUMBER (OG-LGRT) 1-899ROUTE RESTRICTION CLASS (RSC) 0-15FLAG OF 3 OR 6 DIGITS (FLAG) 3 Digits/6 DigitsDESTINATION (AREA/OFFICE) CODE (DC) MAX. 6 DIGITSRESTRICTION DATA (RES) 0/1REMARKS FLAG Select either 3 Digits or 6 Digits check box.RES 0 = Area/Office code is restricted. 1 = Area/Office code is allowed.OG-LGRT Assign a unique LGRT No. in the Fusion network. DC should not include the access code.DCRSC assigned by the ARSCN command.RSC