NEC Neax 2400 Ipx Office Data Specification
Have a look at the manual NEC Neax 2400 Ipx Office Data Specification online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1168 NEC manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
NDA-24298 CHAPTER 4 Page 517 Issue 1 ARTD : Assignment of Route Class Data 4. Data Sheet RT FUNCTIONREMARKS 1OSGSSignal Interface for Outgoing 0=CCIS No.7 1=RingDown 2 = Second Dial Tone 3 = Not used 4 = Sender (Immediate Start) Note 5=Not used 6 = Sender (Delay Dial Start) 7 = Sender (Wink start) 8-15= Not used Note:The select signal in ONSG should be “DP.” 2 ONSGSignal Selection for Outgoing 0 = Not used 1 = DP, 10 pps, 33% Make 2 = PB, 60msec. Interruption or CCIS No.7 3=DP/PB 4=MF 5 = DP, 20 pps, 33% Make 6=Not used 7 = DP, 20 pps, 50% Make 8 = PB, 120 msec. Interruption 9 = DP, 10 pps, 40% Make 10 = MFC 11-15= Not used 3ISGS Signal Interface for Incoming 0 = CCIS No.7 1 = Ring Down 2 = Second Dial Tone 3 = Not used 4 = Sender (Immediate Start) Note 5=Not used 6 = Sender (Delay Dial Start) 7 = Sender (Wink Start) 8-15= Not used Note:The select signal in INSG should be “DP.” 4INSGSignal Selection for Incoming 0 = Not used 1 = DP, 10 pps, 33% Make 2 = PB, 60msec. Interruption or CCIS No.7 3=DP/PB 4=MF 5 = DP, 20 pps, 33% Make 6=Not used 7 = DP, 20 pps, 50% Make 8 = PB, 120 msec. Interruption 9 = DP, 10 pps, 40% Make 10 = MFC 11-15= Not used 5TFType of Trunk Function 0=Not used 1 = Outgoing Trunk (OGT) 2 = Incoming Trunk (ICT) 3 = Bothway Trunk (BWT)
CHAPTER 4 NDA-24298 Page 518 Issue 1 ARTD : Assignment of Route Class Data Figure 4-15 SMDR2 b0b1b2b3 0/1: -/Incoming Call (SMDR is required) 0/1: SMDR is required for toll and local out- going calls/SMDR is required only for toll outgoing calls. 0: 1: 2: 3:Metering pulses are necessary. Hexadecimal assignment is “01.” Example: b0b1b2b3 00 01 84 21b0=bit 0 b 1=bit 1... The following explains what hexadecimal data “1” means for SMDR2: For incoming calls SMDR is required because Bit 0 is assigned as one (1). SMDR is required for toll and local outgoing calls because Bit 1 is assigned as zero (0). Metering pulses are detected by the system; therefore Bit 2 is zero (0) and Bit 3 is zero (0).
NDA-24298 CHAPTER 4 Page 519 Issue 1 ARTD : Assignment of Route Class Data RT FUNCTIONREMARKS 1OSGSSignal Interface for Outgoing 0=CCIS No.7 1=RingDown 2 = Second Dial Tone 3 = Not used 4 = Sender (Immediate Start) Note 5=Not used 6 = Sender (Delay Dial Start) 7 = Sender (Wink start) 8-15= Not used Note:The select signal in ONSG should be “DP.” 2 ONSGSignal Interface for Outgoing 0 = Not used 1 = DP, 10 pps, 33% Make 2 = PB, 60msec. Interruption or CCIS No.7 3=DP/PB 4=MF 5 = DP, 20 pps, 33% Make 6=Not used 7 = DP, 20 pps, 50% Make 8 = PB, 120 msec. Interruption 9 = DP, 10 pps, 40% Make 10 = MFC 11-15= Not used 3ISGS Signal Interface for Incoming 0 = CCIS No.7 1 = Ring Down 2 = Second Dial Tone 3 = Not used 4 = Sender (Immediate Start) Note 5=Not used 6 = Sender (Delay Dial Start) 7 = Sender (Wink Start) 8-15= Not used Note:The select signal in INSG should be “DP.” 4INSGSignal Selection for Incoming 0 = Not used 1 = DP, 10 pps, 33% Make 2 = PB, 60msec. Interruption or CCIS No.7 3=DP/PB 4=MF 5 = DP, 20 pps, 33% Make 6=Not used 7 = DP, 20 pps, 50% Make 8 = PB, 120 msec. Interruption 9 = DP, 10 pps, 40% Make 10 = MFC 11-15= Not used 5TFType of Trunk Function 0=Not used 1 = Outgoing Trunk (OGT) 2 = Incoming Trunk (ICT) 3 = Bothway Trunk (BWT)
CHAPTER 4 NDA-24298 Page 520 Issue 1 ARTD : Assignment of Route Class Data 6TCLTrunk Class Specify the kind of trunk 1 = DDD Line 2 = FX 3 = WATS Line 4 = Tie Line/Announcement Trunk 5 = CCSA 6 = Toll Terminal 7= CAS Line 8 = Paging 9 = Code Call Trunk 10 = Dictation Trunk 11 = General Paging 12 = Radio Paging Trunk 13 - 31= Not used 7L/TLine/Trunk Identification 0 = Not used (Line) 1 = Trunk11111Always assign data “1.” 8RLPTrunk Release Pattern 0 = Calling Party Release (Outgoing only) 1=Not used 2 = First Party Release (either station or trunk side) 3=Not used 9TQOutgoing Trunk Queuing 0 = Out of Service 1 = In Service 10 SMDRDetailed Billing Information 0 = SMDR Out of Service 1 = SMDR In Service (ORT required for receiving all dialed digits) 11TD Tool Denial Battery Reversal 00000Always assign data “0.” 12 DRDistinctive Ringing Pattern This parameter designates whether distinctive ringing will be provided for an incoming call. 0 = Distinctive Ringing is not required (ASYD, SYS 3, Index 3, Bit 0=0) 1 = Distinctive Ringing is required (ASYD, SYS 3, Index 3, Bit 0=1) 13 ACFlexible Routing Pattern Designation When outgoing route selection pattern number is to be determined by the AFRS command, “1” is to be assigned if the Access Code is included in the Number Pattern Code (NPC) 0 = When flexible routing is executed, numbers are translated excluding the Access Code 1 = When the flexible routing is executed, numbers are translated including the Access Code.This data is valid for dummy routes. Assign data “1” for the dummy route. 14 TNTTenant Number Check 0 = Tenant number check is not required in trunk selection.Always assign data “0.” RT FUNCTIONREMARKS
NDA-24298 CHAPTER 4 Page 521 Issue 1 ARTD : Assignment of Route Class Data 15 LSGLine Signal 0=Loop 1 = Ground Start C.O. Line 2=CDH 3 = Caller ID (Loop) 4=Loop 5=E&M Tie Line 6=DX 7=24V4 8 = Loop DID 9 - 11 = Not used 12 = Speech Line (for CCIS No. 7 or Bch of ISDN) 13 = Signal Line (for CCIS No. 7 or Dch of ISDN) 14-15 = Not used 16 SMDR2 Detailed Billing InformationSee Figure 4-15 and Table 4-20. 17 H/MHotel Service in CCIS No. 7 0 = Out of Service 1 = In Service 18MC 00000Always assign data “0.” 19 ANIE911 - ANI Service 0 = Out of Service 1 = In Service 20D 00000Always assign data “0.” 21MSB 00000Always assign data “0.” 22MSW 00000Always assign data “0.” 23 TR0=– 1 = ICPT transfer by group-II signals used.For MPC signaling. Table 4-20 SMDR2 CONTENTS/INPUT 0123456789101112131415 b00-Detailed billing is not required for incoming calls. ×××× 1-Detailed billing is required for incoming calls.×××× b10-Detailed billing is required for toll and local outgoing calls. ×× ×× 1-Detailed billing is required only for toll outgoing calls.×× ×× b2,30- 1-Metering pulses are used.×××× 2- 3-RT FUNCTIONREMARKS
CHAPTER 4 NDA-24298 Page 522 Issue 1 ARTD : Assignment of Route Class Data RT FUNCTIONREMARKS 24 OC 0= - 1 = Originating Category Information is used For MFC signaling (Brazil and Mexico) 25 R/LAttendant-Identification of Incoming Trunk Display. 0 = TN, RT, TK display 1 = C.O. Line Number display 26 RVSDTrunk Reversal Identification This data is necessary when a specific Trunk route provides battery reversal for answer super-vision. 0 = Battery Reversal System 1=Third Wire System 27 TL Tone Level 0000Always assign data “0. 2 8 ANS Answer signal from Trunk side. 0 = No answer signal is given. 1 = Answer signal is given. 2 9 TELPTime Elapse Indication Service 0 = Out of Service 1 = In ServiceTELP (Time Elapse Indication) is a warning tone sent to the caller after a predetermined period of time has elapsed (usually three minutes). 30 PADThis data determines Pad control on the ODT/DTI circuit card. TLT (EMT) DTI 0 = Depending on setting. – 7 = Pad Off(0db) Pad Off(0db) Pad=1-6: Actual PAD value depends on PAD ROM on the ODT/DTI circuit card. (See the NEAX2400 IPX Circuit Card Manual) 3 1 OGRLRelease timing for outgoing trunk connection. 0 = 608 msec. 1 = 224 msec. 2 = 288 msec. 3 = 352 msec. 4 = 416 msec. 5 = 480 msec. 6 = 544 msec. 7 = 608 msec. 8 = 672 msec. 9 = 736 msec. 10 = 800 msec. 11 = 864 msec. 12 = 928 msec. 13 = 992 msec. 14 = 1056 msec. 15 = 1120 msec. Normally assign data “0” For ISDN, see Table 4-21. (Examples of Route Class Settings)
NDA-24298 CHAPTER 4 Page 523 Issue 1 ARTD : Assignment of Route Class Data 3 2 ICRLRelease timing for incoming trunk connections. 0 = 288 msec. Note 1 = 224 msec. 2 = 288 msec. 3 = 352 msec. 4 = 416 msec. 5 = 480 msec. 6 = 544 msec. 7 = 608 msec. 8 = 672 msec. 9 = 736 msec. 10 = 800 msec. 11 = 864 msec. 12 = 928 msec. 13 = 992 msec. 14 = 1056 msec. 15 = 1120 msec. Normally assign data “0. For ISDN, see Table 4-21 (Example of Route Class Settings). Note:160 msec. in case of Loop Dialing Trunk. 33 HDTrunk Hold Timing. 0 = 10 sec. 1 = 2 sec. 2 = 4 sec. 3 = 6 sec. 4 = 8 sec. 5 = 10 sec. 6 = 12 sec. 7 = 14 sec. 8 = 16 sec. 9 = 18 sec. 10 = 20 sec. 11 = 22 sec. 12 = 24 sec. 13 = 26 sec. 14 = 28 sec. 15 = 30 sec. Normally assign data “0. 3 4 GUARDGround Timer Outgoing inhibit timing after trunk release. 0 = 3072 msec. 1 = 512 msec. 2 = 1024 msec. 3 = 1536 msec. 4 = 2048 msec. 5 = 2560 msec. 6 = 3072 msec. 7 = 3584 msec. 8 = 4096 msec. 9 = 4608 msec. 10 = 5120 msec. 11 = 5632 msec. 12 = 6144 msec. 13 = 6656 msec. 14 = 7168 msec. 15 = 7680 msec. Normally assign data “0. For ISDN, see Table 4-21. (Example of Route Class Settings). 35 WINKWidth of a Wink Signal 0 = 160 msec. 1 = 64 msec. 2 = 96 msec. 3 = 128 msec. 4 = 160 msec. 5 = 192 msec. 6 = 224 msec. 7 = 265 msec. 8 = 288 msec. 9 = 320 msec. 10 = 352 msec. 11 = 384 msec. 12 = 416 msec. 13 = 448 msec. 14 = 480 msec. 15 = 512 msec. Normally assign data “0. 36 VAD 0 0 0 0 Always assign data “0. 37 CLD 0 0 0 0 Always assign data “0.” 38 FAForced Account/Forced Authorization Code 0 = Check is not required 1 = Check is required (For Remote Access to System) RT FUNCTIONREMARKS
CHAPTER 4 NDA-24298
Page 524
Issue 1
ARTD : Assignment of Route Class Data
39 BCC.O Line Idle Balance Condition.
0 = Not balanced 1 = BalancedFor Australia only
40 TCMTravel Class Mark
0 = Out of Service 1 = In Service
41 TDMQTandem Off Hook OG Queuing
0 = Out of Service 1 = In Service
42 TRSCTrunk Restriction class
0 = Out of Service 1-15 = In ServiceSee AEFR command.
43 BT Inter-office Busy Service
0 = Out of Service 1 = In ServiceFor CCIS voice route,
assign data “1.
44 PRVLine Trunk Privacy
0 = Privacy Out of Service
1 = Privacy In Service For Busy Verification, Call
Waiting, Executive Right of Way, Paging, Dictation,
Data Communication, etc.).
45 A/DAnalog/Digital Line Data
0 = Analog 1 = DigitalAssign data “1” only for
digital T1 routes or Bch
of ISDN routes.
46 CWCall Waiting Service
0 = Out of Service 1 = In Service
47 TPQPriority OG Queuing
0 = Out of Service 1 = In Service
48 BLDetection of Blocking Signal
0 = No detection 1 = Detection
49 TRKSTrunk Selection Sequence
0 = Select from the trunk which becomes idle first.
1 = Select from the trunk which becomes idle last. Assign this data
reversing to the mate
office data. (Especially,
for CCIS)
50 DPLYNumber Display of D
term between offices
0 = Not given 1 = GivenFor CCIS voice route and
ISDN Bch route.
51 ACD 0 = Out of Service 1 = –0000Always assign data “0”
even ACD application.
52 2W/4W2 Wires/4 Wires
0 = 2 Wires 1 = 4 Wires0 0 0 0 Always assign data “0.
53 FAAT Authorization Code for ATT
0 = Depends on RSC of ATT
1 = Authorization Code always required.
54 GWGateway Option
0 = Out of Service 1 = Data Signaling Trunk
2-15 = Not used
55 TCMA 0 0 0 0 Always assign data “0. RT
FUNCTIONREMARKS
NDA-24298 CHAPTER 4
Page 525
Issue 1
ARTD : Assignment of Route Class Data
56 SMDR3Detailed billing for outgoing in tandem connection.
0 = Required 1 = Not requiredAssign this for the
incoming route (ICRT),
if necessary.
5 7 HDTHeterogeneous Data Trunk
0 = Not Heterogeneous Data Trunk
1 = Heterogeneous Data Trunk
58 CDConsecutive Dialing
0 = Out of Service 1 = In Service
59 CCHCommon Channel Handler
0 = CCH is not mounted (normal setting)
1 = CCH is mounted (ISDN or CCIS line ) 0000Always assign data “0”
even ISDN/CCIS.
60 TC/EC 0 0 0 0 Always assign data “0.
61 IRE Inter-rearranging signal
1 = SupervisoryWhen assigning this
data, always enter zero
(0).
62 SCRStep Call Restriction for Tie Line Call
0 = Step call is restricted.
1 = Step call is not restricted.
63 LYER1Layer 1 (For ISDN)
0 = 23B+D 1 = 30B+D0= µ law country
1= A law country
64 NETUser/Net Identification (For ISDN)
0 = User Side (normal setting)
1 = Network sideNormally assign data
“0.
65 INTInterface Specification (For ISDN)
0 = No.7 1 = N-ISDN2 2 = Australia
3 = INS 1500(NTT) 4 = ITU (CCITT), ETSI
5 = AT&T(#4/#5 ESS) 6 = INS 64 (NTT)
7 = NT DMS 100/DMS 250
8 = Not used
9 = TTC Q931 a protocol Tie Line (JAPAN)
10 = Q-sig, (ETS 300 172)/IS-11572
11 = Seamless
66 DCDialed Number Confirmation (For ISDN)
0 = Sub Addressing
1-15 = DID Addressing NoteNote:Other than 0=
Number of
Main Address
Digits to be
translated.
6 7 HKSHooking Service
0 = Out of Service 1 = In ServiceRT
FUNCTIONREMARKS
CHAPTER 4 NDA-24298 Page 526 Issue 1 ARTD : Assignment of Route Class Data 68 SCFSplit Call Forwarding The call is forwarded to the desired destination assigned at 0 = Split C. F. - All Calls (SSC, SID = 8), Split C. F. - Busy Line (SSC, SID = 10), Split C. F. - Don’t An- swer (SSC, SID = 12) 1 = C. F. - All Calls (SSCA, SIDA = 86), C. F. - Busy Line (SSCA, SIDA = 87), C. F. - Don’t Answer (SS CA, SIDA = 88) This data is valid when ASYD, SYS,INDEX 79, b2 = 1. 69 SMDR4Detailed billing for incoming in tandem connection. 0 = Required 1 = Not requiredAssign this for the outgoing route (OGRT) if necessary. 70 TCMNNumber of digits of TCM (S Code) 0 = No digit 1 = 1 digit 2 = 2 digits 3 = Not usedUse this when ONSG/ INSG = 4 (MF). 71 TCMCTCM and KP Sending Sequence 0 = KP-ST 1 = KP TCM-ST 2 = TCM KP-ST 3 = KP (TCM)-STUse this when ONSG/ INSG = 4 (MF). 7 2 MFSPSending Speed Tone ON Tone OFF Digit/sec. 0 = 68 msec. 68 msec. 7.5 1 = 56 m sec. 5 6 m s ec. (CC ITT No.5 ) Note 2 = 68 msec. 32 msec. 10 3 = 68 msec. 36 msec. 10 4 = 48 msec. 48 msec. 10 5 = 52 msec. 52 msec. 10 6-15 = Not used (In case of MFC) 0 = 24.0 sec. 1 = 5.5 sec. 2 = 7.0 sec. 3 = 8.5 sec. 4 = 10.0 sec. 5 = 11.5 sec. 6 = 13.0 sec. 7 = 14.5 sec. 8 = 16.0 sec. 9 = 17.5 sec. 10 = 20.0 sec. 11 = 22.0 sec. 12 = 24.0 sec. 13 = 26.0 sec. 14 = 28.0 sec. 15 = 30.0 sec. Note:Use this when ONSG/INSG = 4. RT FUNCTIONREMARKS