NEC Neax 2400 Ipx Office Data Specification
Have a look at the manual NEC Neax 2400 Ipx Office Data Specification online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1168 NEC manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
NDA-24298 CHAPTER 4 Page 737 Issue 1 ASID_T : Assignment of Special Incoming – Telephone Number 4. Data Sheet TENANT NUMBER (TN)FUNCTION NUMBER (F) 0-7SPECIFIC TERMINATING GROUP NUMBER (GN) 1-7USER GROUP NUMBER (UGN)SPECIFIC TERMINATING EQUIPMENT REMARKS S/ASPECIAL TELEPHONE NUMBER (STELN) Max. 16 digits 1S A 2S A 3S A 4S A 5S A 6S A 7S A 1S A 2S A 3S A 4S A 5S A 6S A 7S A
CHAPTER 4 NDA-24298 Page 738 Issue 1 ATTD : Assignment of Trunk Test Data ATTD: Assignment of Trunk Test Data 1. General This command assigns, deletes, and displays trunk connection test data. 2. Precautions It cannot be executed to overwrite the existing data in this command. 3. Data Entry Instructions When TYPE=1 Note:Each trunk is automatically tested eight seconds after the previous digits have been sent out. If Test Tone (TT) or Ring Back Tone (RBT) has been acknowledged, an error is indicated. INFORMATION TYPE (TYPE) 1/2ROUTE TYPE (RT TYPE) 1/2ROUTE NUMBER (RT) 1-255RESPONSE PATTERN (RESP) 1-3 LOGICAL ROUTE NUMBER (LGRT) 1-899DIAL CODE (DC) Max. 24 Digits LGRT Enter the Logical Route Number when RT TYPE=2 is assigned. TYPE TYPE 1 = Trunk Test Parameters 2 = LENS of the LTST circuit card 1 = Route Number 2 = Logical Route Number RESP 1 = Test Tone (Continuous 1kHz Tone) 2 = Ring Back Tone 3 = Time Over (No Tone) Note RT TYPE Enter the Route Number when RT TYPE=1 is assigned.RT 1
NDA-24298 CHAPTER 4 Page 739 Issue 1 ATTD : Assignment of Trunk Test Data 4. Data Sheet (a) When TYPE=1 INFORMATION TYPE (TYPE) 1/2ROUTE TYPE (RT TYPE) 1/2ROUTE NUMBER (RT) 1-255LOGICAL ROUTE NUMBER (LGRT) 1-899RESPONSE PATTERN (RESP) 1-3DIAL CODE (DC) Max. 24 Digits
CHAPTER 4 NDA-24298 Page 740 Issue 1 ATTD : Assignment of Trunk Test Data (b) When TYPE=2 INFORMATION TYPE (TYPE) 1/2LINE EQUIPMENT NUMBER (LENS)INDIVIDUAL TRUNK ACCESS CODE (ACC) Max. 3 DigitsTENANT NUMBER (TN) 1-63STATION NUMBER (STN) Max. 6 Digits MG U G LV
NDA-24298 CHAPTER 4 Page 741 Issue 1 ACFS : Assignment of Call Forwarding Station Data ACFS: Assignment of Call Forwarding Station Data 1. General This command is used to set the Call Forwarding - All Calls/Busy Line/Don’t Answer, and further the Split Call Forwarding Services. 2. Precautions 1. The applicable tenant number (TN) range is designated by the ASYD command, SYS 1, INDEX 8. 2. Parameters RCV can be assigned when ASYD, SYS1, INDEX 79, b2 = 1 (Split Call Forwarding is In Service), and data “2 (Split Call Forwarding)” is assigned at the TYPE parameter. 3. Data Entry Instructions CALL FORWARDING TYPE (TYPE) 1/2 TENANT NUMBER (TN)STATION NUMBER (STN)CALL FORWARDING KIND (SRV) V/B/D/NCALL FORWARDING DESTINATION NUMBER (CFD) RESTRICTED CALL KIND (RCV) T/SREMARKS SRV V = All Calls B = Busy Line D = Dont Answer N = PS Incoming Incomplete RCV T = Trunk S = StationCFD CALL FORWARDING DESTINATION NUMBER. Maximum is 24 digits. TYPE 1 = Call Forwarding 2 = Split Call Forwarding
CHAPTER 4 NDA-24298 Page 742 Issue 1 ACFS : Assignment of Call Forwarding Station Data 4. Data Sheet TENANT NUMBER (TN)STATION NUMBER (STN)CALL FORWARDING TYPE (TYPE) 1/2RESTRICTED CALL KIND (RCV) 1/2CALL FORWARDING KIND V/B/D/NCALL FORWARDING DESTINATION NUMBER (CFD) MAX. 24 DIGITS
NDA-24298 CHAPTER 4 Page 743 Issue 1 ACFS_T : Assignment of Call Forwarding Station Data – Telephone Number ACFS_T : Assignment of Call Forwarding Station Data – Telephone Number 1. General This command is used to set the Call Forwarding - All Calls/Busy Line/Don’t Answer, and further the Split Call Forwarding Services for each station. The station data of ACFS command can be assigned by using Telephone Number instead. 2. Precautions 1. Only the Telephone Numbers assigned by the ALGSN command can be used. Telephone Numbers by the ALGSL command is not available in this command. 2. In case logging in to a LN, only the Telephone Numbers allocated to the stations within the logged-in node can be used in this command. Also, when logging in to the NCN, the data memory of the whole nodes in the network is to be written. 3. The applicable tenant number (TN) range is designated by the ASYD command, SYS1, INDEX8. 4. The “RCV” parameter can be assigned when ASYD, SYS1, INDEX79, b2=1 (Split Call Forwarding is In Service), and “Split Call Forwarding” is selected in “TYPE” parameter. 3. Data Entry Instructions Note:The existing data is readout by pressing “Get” button after UGN and TELN is entered. UGNCALL FORWARDING TYPE (TYPE)CALL FORWARDING KIND (SRV) KIND OF RECEIVED CALL (RCV) TELEPHONE NUMBER (TELN) Max. 16 digitsCALL FORWARDING DESTINATION NUMBER (CFD) Max. 24 digits TELN Enter the Telephone Number of the station to which this service is to be assigned.CFD Enter the call forwarding destination number within 24 digits. TYPE Select the type of Call Forwarding. Call Forwarding Split Call ForwardingSRV Select the kind of Call Forwarding. All Calls Busy Line Dont Answer PS Incoming IncompleteRCV When Type = Split Call Forwarding is entered, select the kind of received call. Trunk Telephone Number
CHAPTER 4 NDA-24298 Page 744 Issue 1 ACFS_T : Assignment of Call Forwarding Station Data – Telephone Number 4. Data Sheet UGNTELEPHONE NUMBER (TELN) Max. 16 digitsCALL FORWARDING TYPE (TYPE)KIND OF RECEIVED CALL (RCV)CALL FORWARDING KIND (SRV)CALL FORWARDING DESTINATION NUMBER (CFD) Max. 24 digits
NDA-24298 CHAPTER 4 Page 745 Issue 1 ACFCL : Assignment of Call Forwarding by SFC for LDM ACFCL : Assignment of Call Forwarding by SFC for LDM 1. General This command is used to readout, assign, and delete the data related to Call Forwarding features. The data is written in the Local Data Memory (LDM). 2. Precautions 1. Depending on the system data setting by ASYD SYS1, INDEX5 bit0 (Access Code for C.F. – Busy and C.F. – Don’t Answer is the same or separated) and INDEX79 bit2 (Split Call Forwarding is in service or not), required parameters differ in this command. See the Data Sheet on the next pages for required parameters as to each type. 2. The applicable tenant number (TN) range is designated by the ASYD command, SYS1, INDEX8. 3. Data Entry Instructions Note:Unnecessary parameters can be skipped owing to the kind of Call Forwarding features. DAY/NIGHT MODE (D/N)TENANT NUMBER (TN)SERVICE FEATURE CLASS (SFC) 0-15 CALL FORWARD ALL DESTINATION (CFAD) MAX. 24 DIGITS [0-9, *, #]CALL FORWARD BUSY DESTINATION (CFBD) MAX. 24 DIGITS [0-9, *, #]CALL FORWARD DO NOT ANSWER DESTINATION (CFDD) MAX. 24 DIGITS [0-9, *, #]Maximum 24 digits can be assigned to the Call Forwarding destination number as to each feature. SFC D/N Enter the Service Feature Class defined by the ASFC command. Since SFC=0 is preserved for ATTCON, a station can use the SFC in the range from 1 to 15. CALL FORWARD ALL CALLS DESTINATION FOR STATIONS (CFAS) MAX. 24 DIGITS [0-9, *, #]CALL FORWARD BUSY DESTINATION FOR STATIONS (CFBS) MAX. 24 DIGITS [0-9, *, #]CALL FORWARD DO NOT ANSWER DESTINATION FOR STATIONS (CFDS) MAX. 24 DIGITS [0-9, *, #] CALL FORWARD ALL CALLS DESTINATION FOR TRUNKS (CFAT) MAX. 24 DIGITS [0-9, *, #]CALL FORWARD BUSY DESTINATION FOR TRUNKS (CFBT) MAX. 24 DIGITS [0-9, *, #]CALL FORWARD DO NOT ANSWER DESTINATION FOR TRUNKS (CFDT) MAX. 24 DIGITS [0-9, *, #] D = Day Mode N = Night Mode
CHAPTER 4 NDA-24298 Page 746 Issue 1 ACFCL : Assignment of Call Forwarding by SFC for LDM 4. Data Sheet (a) TYPE = 1 (ASYD SYS1, INDEX5 bit0 = 0 and INDEX79 bit2 = 0 is assigned); (b) TYPE = 2 (ASYD SYS1, INDEX5 bit0 = 1 and INDEX79 bit2 = 0 is assigned); DAY/NIGHT MODE (D/N)TENANT NUMBER (TN)SERVICE FEATURE CLASS (SFC) 0-15CALL FORWARD ALL DESTINATION (CFAD) MAX. 24 DIGITS [0-9, *, #]CALL FORWARD BUSY/ DO NOT ANSWER DESTINATION (CFBD/CFDD) MAX. 24 DIGITS [0-9, *, #] DAY/ NIG HT MODE (D/N)TENANT NUMBER (TN)SERVICE FEATURE CLASS (SFC) 0-15 CALL FORWARD ALL DESTINATION (CFAD) MAX. 24 DIGITS [0-9, *, #]CALL FORWARD BUSY DESTINATION (CFBD) MAX. 24 DIGITS [0-9, *, #]CALL FORWARD DO NOT ANSWER DESTINATION (CFDD) MAX. 24 DIGITS [0-9, *, #] D/N TN SFC CFAD MAX. 24 DIGITS [0-9, *, #]CFBD MAX. 24 DIGITS [0-9, *, #]CFDD MAX. 24 DIGITS [0-9, *, #] D/N TN SFC CFAD MAX. 24 DIGITS [0-9, *, #]CFBD MAX. 24 DIGITS [0-9, *, #]CFDD MAX. 24 DIGITS [0-9, *, #] D/N TN SFC CFAD MAX. 24 DIGITS [0-9, *, #]CFBD MAX. 24 DIGITS [0-9, *, #]CFDD MAX. 24 DIGITS [0-9, *, #]