NEC Neax 2400 Ipx Office Data Specification
Have a look at the manual NEC Neax 2400 Ipx Office Data Specification online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1168 NEC manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
NDA-24298 CHAPTER 4 Page 297 Issue 1 ATCP : Assignment of Time/Pattern Change Information Data ATCP: Assignment of Time/Pattern Change Information Data 1. General This command assigns the time period corresponding to each Time of Day Change Pattern Number (TDPTN). These Time of Day Change Patterns are used to change the routes to be used during a specific time period so that trunks can be used effectively and call charges can be kept to a minimum. 2. Precautions 1. The data assigned by this command is required for the ACBC/AOPR/ASDC commands. However, when the Clocked Manual Override data is assigned by the ACMO command (used for changing routes during a specific time period), the ACMO data has priority over data assigned by the ATCP command to the ACBC/AOPR/ASDC commands. 2. Assignment intervals must be at least 30 minutes. 3. If the time data is assigned in duplicate, the latter assignment shall take effect. For example, “9:00 ~ 12:00 = TDPTN 1” is set then “11:00 ~ 15:00 = TDPTN 2” is specified, the time setting “9:00 ~ 11:00 = TDPTN 1”/“11:00 ~ 15:00 = TDPTN” is to be executed. 3. Data Entry Instructions The time period TDPTN is effective. 09 2000 : 00 TIME DATA FOR TDPTN TIME DATA FOR TDPTN : : :20 0900 : 00 : : (FROM) (TO) HOUR MINUTE HOUR MINUTETIME OF DAY CHANGE PATTERN (TDPTN) 0-7REMARKS 0 1 2 3 Enter the pattern number corresponding to the TDPTN assigned at AOPR/AOPRL/ASDC commands. NoteTDPTN Note:“TDPTN = 0” is also used in default setting (in unspecified time period). Thus the assignment “TDPTN = 0” means nothing in this command.
CHAPTER 4 NDA-24298 Page 298 Issue 1 ATCP : Assignment of Time/Pattern Change Information Data 4. Data Sheet Note 1:Assignment intervals must be at least 30 minutes. Note 2:The system fills in any unassigned time patterns for a 24-hour period. TIME DATA FOR TDPTNTIME OF DAY CHANGE PAT T E R N (TDPTN) 0 – 7REMARKS (FROM) (TO) HOUR MINUTE HOUR MINUTE ::0 ::1 ::2 ::3 ::4 ::5 ::6 ::7
NDA-24298 CHAPTER 4 Page 299 Issue 1 AFRS : Assignment of Flexible Route Selection Data AFRS: Assignment of Flexible Route Selection Data 1. General This command assigns the area and/or office code data for the related OPR. 2. Precautions 1. The applicable Tenant Number (TN) range is designated by the ASYD command, SYS1, INDEX8. If data in this command is common for all tenants (ASYD command, SYS1, INDEX93, bit4=1), assign TN parameter as data “1” for all tenants. 2. After an Outgoing Route Selection Pattern Number (OPR) has been assigned in this command, it is necessary to assign the LCR routing pattern/six (6) digits routing pattern by the AOPR/ASDC command respectively. 3. It should be noted that the access code may or may not be included in the Number Pattern Code (NPC) depending upon the assignment of the AC parameter by the ARTD command. If zero (0) is assigned, the access code is not included. If one (1) is assigned, the access code must be included. 4. Assign the dummy route number in the RT parameter. 5. When assigning such a number as shown below to parameter “NPC”, enter “T” code to the end digit of “NPC.” Example: When assigning 90 and 900 to NPC: NumberInput Number for NPCOPR 90 90T X 900 900 Y
CHAPTER 4 NDA-24298 Page 300 Issue 1 AFRS : Assignment of Flexible Route Selection Data 3. Data Entry Instructions NPC is the Toll Distinctive Code (TDC), NPA and or NXX. This data can be a maximum of sixteen (16) digits. This data may include the access code for LCR/LCRS.NPC Since the OPR is an intermediate to assign the AOPR command, an arbitrary number may be entered ranging from 1 to 4000. (OPR0 is used for number not to be dialed in the network.)OPR Dummy route number assigned by the ASPA command.RT TENANT NUMBER (TN) ROUTE NUMBER (RT)NUMBER PATTERN CODE (NPC) MAX. 16 DIGITSOUTGOING ROUTE SELECTION NUMBER (OPR) 0-4000REMARKS 1 1 912132563
NDA-24298 CHAPTER 4 Page 301 Issue 1 AFRS : Assignment of Flexible Route Selection Data 4. Data Sheet TENANT NUMBER (TN)ROUTE NUMBER (RT)NUMBER PATTERN CODE (NPC) MAX. 16 DIGITSOUTGOING ROUTE SELECTION NUMBER (OPR) 0 – 4000REMARKS
CHAPTER 4 NDA-24298 Page 302 Issue 1 AFRSL : Assignment of Flexible Route Selection Data for LDM AFRSL: Assignment of Flexible Route Selection Data for LDM 1. General This command assigns the area and/or office code data for the OPR assigned by the AOPRL command. This data is written in Local Data Memory (LDM). 2. Precautions 1. The applicable Tenant Number (TN) range is designated by the ASYD command, SYS1, INDEX8. If data of this command is common for all tenants (ASYDL command, SYS1, INDEX800, bit4=1), assign TN parameter as data “1” for all tenants. 2. After an Outgoing Route Selection Pattern Number (OPR) has been assigned in this command, it is necessary to assign the LCR routing pattern/six (6) digits routing pattern by the AOPRL/ASDCL command respectively. 3. The access code may or may not be included in the Number Pattern Code (NPC) depending upon the assignment of the AC parameter by the ARTD command. If zero (0) is assigned, the access code is not included. If one (1) is assigned, the access code must be included. 4. Assign the dummy route number in the LGRT parameter. 5. When assigning such a number as shown below to parameter “NPC”, enter “T” code to the end digit of “NPC.” Example: When assigning 90 and 900 to NPC: NumberInput Number for NPCOPR 90 90T X 900 900 Y
NDA-24298 CHAPTER 4 Page 303 Issue 1 AFRSL : Assignment of Flexible Route Selection Data for LDM 3. Data Entry Instructions NPC is the Toll Distinctive Code (TDC), NPA and or NXX. This data can be a maximum of sixteen (16) digits. This data may include the access code for LCR/LCRS.NPC Since the OPR is an intermediate to assign the AOPRL command, an arbitrary number may be entered ranging from 1 to 4000. (OPR0 is used for number not to be dialed in the network.)OPR Dummy route number assigned by the ASPAL/ASPAN command.LGRT TENANT NUMBER (TN) LOGICAL ROUTE NUMBER (LGRT) 1-899NUMBER PATTERN CODE (NPC) MAX. 16 DIGITSOUTGOING ROUTE SELECTION NUMBER (OPR) 0-4000 REMARKS 1 1 912132563
CHAPTER 4 NDA-24298 Page 304 Issue 1 AFRSL : Assignment of Flexible Route Selection Data for LDM 4. Data Sheet TENANT NUMBER (TN)LOGICAL ROUTE NUMBER (LGRT)NUMBER PATTERN CODE (NPC) MAX. 16 DIGITSOUTGOING ROUTE SELECTION NUMBER (OPR) 0 – 4000REMARKS
NDA-24298 CHAPTER 4 Page 305 Issue 1 AFRSN : Assignment of Flexible Route Selection Data for NDM AFRSN: Assignment of Flexible Route Selection Data for NDM 1. General This command assigns the area and/or office code data for the OPR assigned by the AOPRN command. The data assigned by this command is written in the Network Data Memory (NDM) of the Network Control Node (NCN), updating the NDM at each Local Node (LN). 2. Precautions 1. The applicable Tenant Number (TN) range is designated by the ASYDN command, SYS1, INDEX8. If data of this command is common for all tenants (ASYDN command, SYS1, INDEX800, bit4=1), assign TN parameter as data “1” for all tenants. 2. After an Outgoing Route Selection Pattern Number (OPR) has been assigned in this command, it is necessary to assign the LCR routing pattern/six (6) digits routing pattern by the AOPRN/ASDCN command respectively. 3. It should be noted that the access code may or may not be included in the Number Pattern Code (NPC) depending upon the assignment of AC parameter by the ARTDN command. If zero (0) is assigned, the access code is not included. If one (1) is assigned, the access code must be included. 4. Assign the dummy route number in the LGRT parameter. 5. When assigning such a number as shown below to parameter “NPC”, enter “T” code to the end digit of “NPC.” Example: When assigning 90 and 900 to NPC: NumberInput Number for NPCOPR 90 90T X 900 900 Y
CHAPTER 4 NDA-24298 Page 306 Issue 1 AFRSN : Assignment of Flexible Route Selection Data for NDM 3. Data Entry Instructions NPC is the Toll Distinctive Code (TDC), NPA and or NXX. This data can be a maximum of sixteen (16) digits.This data may include the access code for LCR/LCRS.NPC Since the OPR is an intermediate to assign the AOPRN command,arbitrary number may be entered with a range from 1 to 4000. (OPR0 is used for number not to be dialed in the network.)OPR Dummy route number assigned by the ASPAL/ASPAN command.LGRT TENANT NUMBER (TN) LOGICAL ROUTE NUMBER (LGRT) 1-899NUMBER PATTERN CODE (NPC) MAX. 16 DIGITSOUTGOING ROUTE SELECTION NUMBER (OPR) 0-4000 REMARKS 1 1 912132563