NEC Neax 2400 Ipx Office Data Specification
Have a look at the manual NEC Neax 2400 Ipx Office Data Specification online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1168 NEC manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
NDA-24298 CHAPTER 4 Page 287 Issue 1 ASTPN : Assignment of Signal Translation Pattern for NDM 4. Data Sheet (a) Incoming KIND OF ASSIGNMENT (IC/OG) I/OTENANT NUMBER (TN)LOGICAL ROUTE NUMBER (LGRT) 1-899INCOMING SELECTION TRANSLATION PAT T E R N NUMBER (PNI) 1 – 15REMARKS I
CHAPTER 4 NDA-24298 Page 288 Issue 1 ASTPN : Assignment of Signal Translation Pattern for NDM (b) Outgoing KIND OF ASSIGNMENT (IC/OG) I/OTENANT NUMBER (TN)LOGICAL ROUTE NUMBER (LGRT) 1-899OUTGOING SELECTION TRANSLATION PAT T E R N NUMBER (PNO) 1 – 15REMARKS O
NDA-24298 CHAPTER 4 Page 289 Issue 1 AOSP : Assignment of Outgoing Selection Pattern AOSP: Assignment of Outgoing Selection Pattern 1. General This command assigns skip and additional digits information for Outgoing Selection Translation Pattern Number (PNO). 2. Precautions 1. Before using this command, make sure that an Outgoing Selection Translation Pattern Number (PNO) has been assigned in the ASTP command. 2. The transmit number translation of the OGC/OGCA method outgoing calls are done by ASTP/AOSP command. Since the additional number and skip digits can be assigned by the AOPR/AADC command for LCR/LCRS method, the ASTP/AOSP command may not be required. 3. Data Entry Instructions Enter the PNO assigned by the ASTP command.PNO NUMBER OF DIGITS SKIPPED (SKIP) 0-24 NUMBER OF ADDITIONAL DIGITS (ADD) 0-4ADDITIONAL DIGIT INFORMATION (DC) MAXIMUM 4 DIGITS OUTGOING SELECTION TRANSLATION PATTERN NUMBER (PNO) 1-15 Enter the number of digits to be entered in DC parameter.ADD SKIPDC Enter desired skip digits if required.Enter desired additonal numbers (maximum 4 digits).
CHAPTER 4 NDA-24298 Page 290 Issue 1 AOSP : Assignment of Outgoing Selection Pattern 4. Data Sheet OUTGOING SELECTION TRANSLATION PATTERN NUMBER (PNO) 1 – 15NUMBER OF DIGITS SKIPPED (SKIP) 0 – 24NUMBER OF ADDITIONAL DIGITS (ADD) 0 – 4ADDITIONAL DIGIT INFORMATION (DC) MAXIMUM 4 DIGITSREMARKS 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
NDA-24298 CHAPTER 4 Page 291 Issue 1 AOSPL : Assignment of Outgoing Selection Pattern for LDM AOSPL: Assignment of Outgoing Selection Pattern for LDM 1. General This command assigns skip and additional digits information for Outgoing Selection Translation Pattern Number (PNO). This data is written in Local Data Memory (LDM). 2. Precautions 1. Before using this command, make sure that an Outgoing Selection Translation Pattern Number (PNO) has been assigned in the ASTPL command. 2. The transmit number translation of the OGC/OGCA method outgoing calls are done by ASTPL/AOSPL command. Since the additional number and skip digits can be assigned by the AOPRL/AADCL command for LCR/LCRS method, the ASTPL/AOSPL command may not be required. 3. Data Entry Instructions Enter the PNO assigned by the ASTPL command.PNO NUMBER OF DIGITS SKIPPED (SKIP) 0-24NUMBER OF ADDITIONAL DIGITS (ADD) 0-4ADDITIONAL DIGIT INFORMATION (DC) MAXIMUM 4 DIGITS OUTGOING SELECTION TRANSLATION PATTERN NUMBER (PNO) 1-15 Enter the number of digits to be entered in DC parameter. If SKIP=0, ADD must be assigned to 1-4.ADD SKIPDC Enter desired skip digits if requiredEnter desired additonal numbers within 4 digits.
CHAPTER 4 NDA-24298 Page 292 Issue 1 AOSPL : Assignment of Outgoing Selection Pattern for LDM 4. Data Sheet OUTGOING SELECTION TRANSLATION PATTERN NUMBER (PNO) 1 – 15NUMBER OF DIGITS SKIPPED (SKIP) 0 – 24NUMBER OF ADDITIONAL DIGITS (ADD) 0 – 4ADDITIONAL DIGIT INFORMATION (DC) MAXIMUM 4 DIGITSREMARKS 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
NDA-24298 CHAPTER 4 Page 293 Issue 1 AOSPN : Assignment of Outgoing Selection Pattern for NDM AOSPN: Assignment of Outgoing Selection Pattern for NDM 1. General This command assigns skip and additional digits information for Outgoing Selection Translation Pattern Number (PNO) in Fusion Network. The data assigned by this command is written in the Network Data Memory (NDM) of the Network Control Node (NCN), updating the NDM at each Local Node (LN). 2. Precautions 1. Before using this command, make sure that an Outgoing Selection Translation Pattern Number (PNO) has been assigned in the ASTPN command. 2. The transmit number translation of the OGC/OGCA method outgoing calls are done by ASTPN/AOSPN command. Since the additional number and skip digits can be assigned by the AOPRN/AADCN command for LCR/LCRS method, the ASTPN/AOSPN command may not be required. 3. Data Entry Instructions Enter the PNO assigned by the ASTPN command.PNO NUMBER OF DIGITS SKIPPED (SKIP) 0-24NUMBER OF ADDITIONAL DIGITS (ADD) 0-4ADDITIONAL DIGIT INFORMATION (DC) MAXIMUM 4 DIGITS OUTGOING SELECTION TRANSLATION PATTERN NUMBER (PNO) 1-15 Enter the number of digits to be entered in DC parameter. If SKIP=0, ADD must be assigned to 1-4.ADD SKIPDC Enter desired skip digits if requiredEnter desired additonal numbers within 4 digits.
CHAPTER 4 NDA-24298 Page 294 Issue 1 AOSPN : Assignment of Outgoing Selection Pattern for NDM 4. Data Sheet OUTGOING SELECTION TRANSLATION PATTERN NUMBER (PNO) 1 – 15NUMBER OF DIGITS SKIPPED (SKIP) 0 – 24NUMBER OF ADDITIONAL DIGITS (ADD) 0 – 4ADDITIONAL DIGIT INFORMATION (DC) MAXIMUM 4 DIGITSREMARKS 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
NDA-24298 CHAPTER 4 Page 295 Issue 1 ACMO : Assignment of Clocked Manual Override ACMO: Assignment of Clocked Manual Override 1. General This command assigns the Clocked Manual Override data, which is used for changing routes during a specific day and specific time period, such as a holiday (Month/Day/Hour/Minute). 2. Precautions 1. The BLOCK parameter is a data index (0-7). A maximum of eight kinds of Clocked Manual Override Data can be assigned. 2. The PTN parameter corresponds to the TDPTN parameter assigned by the AOPR/ASDC command. 3. The Clocked Manual Override data assigned by ACMO command has priority over the Time Pattern data assigned by the ATCP command. 4. Time is designated in Military Time. 24 cannot be used as Hour designation. 5. A single set of PTN (Pattern Number) and START/END date and time is to be assigned to a BLOCK Number. Also the same PTN can be specified to multiple BLOCK Numbers. 6.“PTN = 0” is also used in default setting (in unspecified time period). Thus the assignment “PTN = 0” means nothing in this command. 3. Data Entry Instructions Enter a block number for a Clocked Manual Override dataMonth/Day ex.) 09/20 = September 20 BLOCK BLOCK NUMBER (BLOCK) 0-7PATTERN NUMBER (PTN) 0-7 Pattern number (0-7) assigned by the AOPR/AOPRL/ASDC command.PTN Hour/MinuteTIME DATE START END DATE TIME DATE TIMEREMARKS 09 20 17 00 09 21 09 00
CHAPTER 4 NDA-24298 Page 296 Issue 1 ACMO : Assignment of Clocked Manual Override 4. Data Sheet BLOCK NUMBER (BLOCK) 0 – 7PATTERN NUMBER (PTN) 0 – 7START END REMARKS DATE TIME DATE TIME //// //// //// //// //// //// //// ////