Home
>
Lucent Technologies
>
Communications System
>
Lucent Technologies DEFINITY Enterprise Communications Server Release 8.2 Instructions Manual
Lucent Technologies DEFINITY Enterprise Communications Server Release 8.2 Instructions Manual
Have a look at the manual Lucent Technologies DEFINITY Enterprise Communications Server Release 8.2 Instructions Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 413 Lucent Technologies manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
DEFINITY ECS Release 8.2 Administrator’s Guide 555-233-506 Issue 1.1 June 2000 Screen reference 927 System Parameters Call Coverage / Call Forwarding 17 However, you can enter y in this field to have QSIG VALU call coverage take precedence. In this case, if the Coverage After Forwarding option on the Station screen is enabled for a user, then QSIG Diversion with Rerouting is not be attempted. Station Hunt Before Coverage This field allows you to choose whether a call to a busy station performs station hunting before going to coverage. Call Forward Override This field specifies how to treat a call from a forwarded-to party to the forwarded-from party. Coverage After Forwarding This field governs whether an unanswered forwarded call is provided coverage treatment. Valid entries Usage y/n Enter y to allow Coverage After Forwarding to work when it is activated on a user’s Station screen and Diversion with Rerouting is also turned on. Valid entries Usage y/n Enter y to use Station Hunt Before Coverage. Valid entries Usage y Overrides the Call Forwarding feature by allowing a forwarded-to station to complete a call to the forwarded-from station. nDirects the system to forward calls to a station even when they are from the forwarded-to party. Valid entries Usage y Coverage treatment is provided to unanswered forwarded calls. nNo coverage treatment is provided to unanswered forwarded calls. The call remains at the forwarded-to destination.
DEFINITY ECS Release 8.2
Administrator’s Guide 555-233-506 Issue 1.1
June 2000
Screen reference
928 System Parameters Call Coverage / Call Forwarding
17
Field descriptions for page 2
Screen 188. System-Parameters Coverage-Forwarding
Coverage Of Calls Redirected Off-Net Enabled
This field allows you to enable/disable the Coverage of Calls Redirected Off-Net
(CCRON) feature. This field provides a quick means of disabling this feature if
the demand on the call classifier port resources degrades other services provided
by the switch. The Coverage of Calls Redirected Off-Net field on this screen must
be
y to administer this field.
Activate Answer Detection (Preserves SBA) On
Final CCRON Cvg Point
This field appears only if the Coverage of Calls Redirected Off-Net Enabled field
on this screen is
y.
When the system redirects a call off-net at the final coverage point in a coverage
path, the system can apply no further coverage treatment even if the call is
unanswered. The only reason for activating answer detection on such a call is to
maintain the simulated bridged appearance (SBA) on the principal’s phone that
allows the principal to answer or bridge onto the call. However, when the system
monitors the call through use of a call classifier port, there is an inherent
cut-through delay following the detection of answer at the far end. This field has
no consequence when the off-net call is carried end-to-end by ISDN facilities; the
SBA is maintained and there is no cut-through delay.
Valid entries Usage
y
DEFINITY ECS monitors off-net coverage/forwarded calls
and provides further coverage treatment for unanswered calls.
nDEFINITY ECS does not monitor offnet coverage/forwarded
calls. No further coverage treatment is provided if such calls
are unanswered.
change system-parameters coverage-forwarding Page 2 of 2
SYSTEM PARAMETERS -- CALL COVERAGE / CALL FORWARDING
COVERAGE OF CALLS REDIRECTED OFF-NET (CCRON)
Coverage Of Calls Redirected Off-Net Enabled? y
Activate Answer Detection (Preserves SBA) On Final CCRON Cvg Point? y
Ignore Network Answer Supervision? y
Disable call classifier for CCRON over ISDN trunks? n
DEFINITY ECS Release 8.2 Administrator’s Guide 555-233-506 Issue 1.1 June 2000 Screen reference 929 System Parameters Call Coverage / Call Forwarding 17 Ignore Network Answer Supervision This field appears only if the Coverage of Calls Redirected Off-Net Enabled field on this screen is y. CCRON may use a call classifier port to determine whether an off-net coverage or forwarded call has been answered, discarding other information that may indicate an answered state. However, some customers pay the operating company to provide network answer supervision on their trunks and desire that CCRON not discard that information. They may preserve this service by setting this field to n. On the other hand, beware when you tandem a call over a tie trunk through another switch node from where it redirects to the public network over non-ISDN facilities. If the trunk on the far-end node sends a timed answer supervision, that may get tandemed back to the originating switch as a network answer. In such a scenario, the originating switch interprets the call as answered, leading to some undesirable behavior. To avoid these calls from mistakenly be treated as answered, set this field to y. An unfortunate consequence is that a short cut-through delay that is inherent to call classification is introduced when the call is answered. Disable call classifier for CCRON over ISDN trunks When a CCRON call routes offnet over ISDN end-to-end facilities, no call classifier is attached to the call. If, subsequently during the call, an ISDN PROGRESS or ALERT message is received that indicates that interworking has occurred, a call classifier is normally attached to the call and assumes precedences Valid entries Usage y Directs the system to maintain a simulated bridged appearance on the principal when redirecting to a final off-net coverage point. nAllows the system to drop the SBA on the principal’s phone when the call redirects off-net at the last coverage point, eliminating the cut-through delay inherent in CCRON calls, but sacrificing the principal’s ability to answer the call. Valid entries Usage y Ignore network answer supervision and rely on the call classifier to determine when a call is answered. nTreat network answer supervision as a true answer.
DEFINITY ECS Release 8.2 Administrator’s Guide 555-233-506 Issue 1.1 June 2000 Screen reference 930 System Parameters Country-Options 17 over ISDN trunk signalling. This field provides a customer the means of directing the switch to dispense with the call classifier on interworked calls and rely on the ISDN trunk signalling messages. System Parameters Country-Options This screen implements parameters associated with certain international (including North American) call characteristics. You cannot change this screen. See your Lucent representative if you want to modify any of the values here. Refer to the following table for country codes throughout this screen. Country code table Valid entries Usage y Use y to disable the call classifier for CCRON calls over interworked trunk facilities. nUse n to enable the call classifier for CCRON calls over interworked trunk facilities. Code Country 1 United States, Canada 2Australia 3Japan 4Italy 5Netherlands 6Singapore 7Mexico 8Belgium, Luxembourg 9Saudi Arabia 10United Kingdom 11Spain 12France 13Germany 14Czech Republic, Slovakia 15Russia (CIS)
DEFINITY ECS Release 8.2
Administrator’s Guide 555-233-506 Issue 1.1
June 2000
Screen reference
931 System Parameters Country-Options
17
Field descriptions for page 1
Screen 189. System Parameters Country-Options
Companding Mode
Identifies the companding algorithm to be used by system hardware.
16Argentina
17Greece
18China
19Hong Kong
20Thailand
21Macedonia
22Poland
23Brazil
24Nordic
25South Africa
Valid entries Usage
A-law
Generally used outside the US
Mu-law Generally used in the US
Code Country
change system-parameters country-options Page 1 of 7
SYSTEM PARAMETERS COUNTRY-OPTIONS
Companding Mode: Mu-Law Base Tone Generation Set: 1
440Hz PBX-dial Tone? n 440Hz Secondary-dial Tone? n
Analog Ringing Cadence: 1 Set Layer 1 timer T1 to 30 seconds? n
Analog Line Transmission: 1
64/84xx Display Character Set? Roman
Howler After Busy: y Disconnect on No Answer by Call Type: y
TONE DETECTION PARAMETERS
Tone Detection Mode: 5 Dial Tone Validation Timer:
Interdigit Pause: short
DEFINITY ECS Release 8.2 Administrator’s Guide 555-233-506 Issue 1.1 June 2000 Screen reference 932 System Parameters Country-Options 17 Base Tone Generation Set The country code identifies the base tone generation set to be used. This field is meaningful only if the system tone detector is a TN780, vintage 4 or a TN2182. A TN780 vintage 5 or greater or a TN2182 is required if Belgian Tones (Country code 8) are specified. 440Hz PBX-dial Tone Specifies whether the switch (primary) dial tone will be changed to a continuous 440Hz/-17 tone. 440Hz Secondary-dial Tone Specifies whether the Secondary (CO) dial tone will be changed to a continuous 440Hz/-17 tone. Analog Ringing Cadence The country code identifies the ringing cadence to be used by analog phones in the system. Valid entries Usage 1 –25 Refer to the Country code table at the beginning of this screen description. Valid entries Usage y/n A value of n implies the tone will either be administered on a later page of this screen or, if no individual definition is administered, as defined in Base Tone Generation Set. Valid entries Usage y/n A value of n implies the tone will either be administered on a later page of this screen or, if no individual definition is administered, as defined in Base Tone Generation Set. Valid entries Usage 1 to 25Refer to the Country code table at the beginning of this screen description. For more information on, see Audible Ringing Patterns in DEFINITY ECS System Description.
DEFINITY ECS Release 8.2 Administrator’s Guide 555-233-506 Issue 1.1 June 2000 Screen reference 933 System Parameters Country-Options 17 Set Layer 1 timer T1 to 30 seconds Analog Line Transmission The country code identifies the transmission and signaling parameters. Enhanced 64xx/84xx Display Character Set Howler After Busy Plays howler tone when users leave their analog phone off-hook too long. Disconnect on No Answer by Call Type Drops outgoing trunk calls (except DCS and AAR) that users leave unanswered too long. Valid entries Usage y/n Specifies whether the Layer 1 timer is set to 30 seconds. Valid entries Usage 1 –25Refer to the Country code table at the beginning of this screen description. Valid entries Usage cyrillic katakana roman ukranian Indicate the enhanced character set to display. SeeEnhanced Telephone Display for more information. Valid entries Usage y/n Enables howler tone. Valid entries Usage y/n Enables the system to disconnect calls that are not answered.
DEFINITY ECS Release 8.2 Administrator’s Guide 555-233-506 Issue 1.1 June 2000 Screen reference 934 System Parameters Country-Options 17 Tone Detection Mode The country code specifies the type of tone detection used on a TN420B (or later) tone-detection circuit pack. Dial Tone Validation Timer Displays number of milliseconds that the dial tone validation routine will use to sample transmissions. This field appears only when Tone Detection Mode is equal to 4 or 5. (Valid with TN420C or later Tone Detector circuit pack.) Interdigit Pause Specifies the maximum length of the inter-digit pause. Breaks lasting less than this range will be bridged or ignored. (Valid with TN420C or later Tone Detector circuit pack.) Valid entries Usage 1 Precise Italian tone detection algorithm 2Precise Australian tone detection algorithm 3Precise UK tone detection algorithm 4Imprecise normal broadband filter algorithm (valid with TN420C or later Tone Detector circuit pack) 5Imprecise wideband filter algorithm (valid with TN420C or later Tone Detector circuit pack) 6 Valid entries Usage 0 –6375 in increments of 25 600 Valid entries Usage short 5 to 30ms long20 to 40ms
DEFINITY ECS Release 8.2
Administrator’s Guide 555-233-506 Issue 1.1
June 2000
Screen reference
935 System Parameters Country-Options
17
Field descriptions for page 2
Screen 190. System Parameters Country-Options
Digital Loss Plan
Provides the default values for digital loss plan and n-party conference loss.
Customize
Appears when the Digital Loss Plan Modification field is enabled on the
System-Parameters Customer-Options screen.
FROM / TO
Identifies the variable digital loss values.
Valid entries Usage
1
- 25Refer to the Country code table at the beginning of this
screen description.
Valid entries Usage
y/n
Enables customization on the 2-party loss table.
Valid entries Usage
-3
- 15An unsigned number is a loss, while a number preceded with
a minus sign is a gain.
Page 1 of 5
OPTIONAL FEATURES
G3 Version: V6 Maximum Ports: 300
Abbreviated Dialing Enhanced List? n CAS Main? n
Access Security Gateway? n Cvg Of Calls Redirected Off-net? n
Analog Trunk Incoming Call ID? n DCS (Basic)? n
A/D Grp/Sys List Dialing Start at 01? n DCS Call Coverage? n
Answer Supervision by Call Classifier? n DCS with Rerouting? n
ARS? y DEFINITY Network Admin? n
ARS/AAR Partitioning? y DS1 MSP? n
ASAI Interface? n
ASAI Proprietary Adjunct Links? n Emergency Access to Attendant? y
Async. Transfer Mode (ATM) PNC? n Extended Cvg/Fwd Admin? n
Async. Transfer Mode (ATM) Trunking? n External Device Alarm Admin? n
ATMS? n Flexible Billing? n
Audible Message Waiting? n Forced Entry of Account Codes? n
Authorization Codes? n Global Call Classification? n
CAS Branch? n Hospitality (Basic)? ydisplay system-parameters country-otpions Page 2 of 7
2 PARTY LOSS PLAN
Digital Loss Plan: 1 Customize? n
TO
12345 6 7 8 9 10 11 12 13 14 15 16 17
1:-10003000030666033
2:00000332230666233
3:00000333230666033
4:150006000030666033
5:0-3-300 -3-3-3-30-3300-333
6:03300686555999533
F 7:03300886555999533
R 8:03300666353966333
O 9:02200553002333933
M 10:33333555003333333
11:00000553230663033
12:00000333-3-30000033
13:00000333-3-30000033
14:00000333-3-3-3000033
15:02000553030666033
16:33333333333333333
17:33333333333333333
DEFINITY ECS Release 8.2
Administrator’s Guide 555-233-506 Issue 1.1
June 2000
Screen reference
936 System Parameters Country-Options
17
Field descriptions for page 3
Screen 191. System Parameters Country-Options
Digital Tone Plan
Provides the default values for tone loss for the selected country.
Customize
Appears when, on the System-Parameters Customer-Options screen, the Digital
Loss Plan Modification field is
y. Valid entries Usage
1
- 25Refer to the Country code table at the beginning of this
screen description.
Valid entries Usage
y/n
Enables customization on the 2-party loss table.
Page 1 of 5
OPTIONAL FEATURES
G3 Version: V6 Maximum Ports: 300
Abbreviated Dialing Enhanced List? n CAS Main? n
Access Security Gateway? n Cvg Of Calls Redirected Off-net? n
Analog Trunk Incoming Call ID? n DCS (Basic)? n
A/D Grp/Sys List Dialing Start at 01? n DCS Call Coverage? n
Answer Supervision by Call Classifier? n DCS with Rerouting? n
ARS? y DEFINITY Network Admin? n
ARS/AAR Partitioning? y DS1 MSP? n
ASAI Interface? n
ASAI Proprietary Adjunct Links? n Emergency Access to Attendant? y
Async. Transfer Mode (ATM) PNC? n Extended Cvg/Fwd Admin? n
Async. Transfer Mode (ATM) Trunking? n External Device Alarm Admin? n
ATMS? n Flexible Billing? n
Audible Message Waiting? n Forced Entry of Account Codes? n
Authorization Codes? n Global Call Classification? n
CAS Branch? n Hospitality (Basic)? ydisplay system-parameters country-otpions Page 3 of 7
TONE & CONFERENCE LOSS PLANS
Digital Tone Plan: 1 Customize? n
TO
12345 6 7 8 9 10 11 12 13 14 15 16 17
Dial:03300666506555500
Confirm:00000000000000000
Reorder:00000000000000000
Busy:00000000000000000
Ringing:00000000000000000
Spec Ring:00000000000000000
Intercept:00000000000000000
Waiting:00000000000000000
Verify:00000000000000000
Intrude:00000000000000000
Zip:333-3-3-3-3-3-3-3-3-3-3-3-300
Music:03300666306333300
End-to-End total loss (dB) in a n-party conference:
3:____ 4:____ 5:____ 6:____