Home
>
Panasonic
>
Communications System
>
Panasonic Cpc+AII/B Digital Business System Release Notes Manual
Panasonic Cpc+AII/B Digital Business System Release Notes Manual
Have a look at the manual Panasonic Cpc+AII/B Digital Business System Release Notes Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 10737 Panasonic manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
secnon 400~ProgrammingGnapter 3. txtenslon Programming (FF3) Auto Set Relocation Code Software Version:CPC-All (all versions); CPC-B Version 3.1 or higherAddress: FF3 (ExtPort)# 41# (OOOl-9999)# DescriptionYou can relocate (or swap) the program settings of one phone to another. The Auto Set Relocation Code enables you to perform the relocation. For example, if the phone from ext.102 is unplugged and moved to an office with a wall jack (port) that is assigned to ext.103, this feature can be used to relocate 102’s programming to 103. In order to move the programming, an Auto Set Relocation Code must be assigned to ext. 103. Programming To assign an Auto Set Relocation Code . . . NotesFF3 (l-l 44)# 41# (OOOl-9999)# ft Extension Port Auto Set Relocation Code (Destination)(000 l-9999) To clear an Auto Set Relocation Code . . . IFF3 .(l-144)# 41# CONF ON/OFFI Moving An Extension. The following procedure explains how to move the program settings from extension 102 to extension 103. 1.At extension 102, pick up the handset.2. Press ‘WO.” 3.Dial extension number 103. 4.Enter the four-digit Auto Set Relocation Code assigned to extension 103. 5.Replace the handset. All programmed extension features, TRS, and LCR settings from 102 will be transferred to 103. Extension 103 will be placed out of service. DBS-70-400DBS Manual - Issued 8/l/95Page 3-49
wapter 3. txtenslon rrogrammlng (w3)bectlon 400~Programming 6.To return extension 103 to service, disconnect then reconnect the extension cable. When extension 103 is retuned to service, it will have the program settings of extension 102. Restrictior~. Phone settings cannot be exchanged between digital and analog (SLT) ports. Page 3-50 DBS Manual - Issued 8/l/95DBS-70-400
Permanent Call Forward Type Software Version:CPC-All (all versions)j CPC-8 Version 3.1 or higherAddress: FF3 (ExtPort)# 42# (0-3)# DescriptionUse this address to enable an extension for Permanent Call Forwarding, so that calls to that extension (if the extension is busy and/or not answered) will be forwarded to another location. This feature is often used for sending calls to Voice Mail, or forwarding peripheral equipment to a single extension port. ProgrammingFF3 (I-144)# 42# (093)# t Extension Port-O=Permanent Call Forwarding is off (displayed as * ). l=Permanent Call Forwarding--Busy/No Answer. 2=Permanent Call Forwarding--Busy. 3=Permanent Call Forwarding--No Answer. Related Programming Permanent Call Forward Extension: FF3 (ExtPort)# 42# (lo-69 or lOO- 699)# NotesInteraction With User-Assigned Call Forwarding.Permanent Cal 1 Forwarding is assigned through system programming, rather than by the user. Permanent Call Forwarding is normally used to forward calls to a voice mail system. An extension user can invoke other forms of call forwarding (no answer, busy, all calls) to temporarily override the Permanent Call Forwarding destination. Resetting To Default (O#J Condition. Entering 0 or pressing CONF will return this program address to its default condition “*“, and will also return the Permanent Call Forward Extension address to default “****” (no extension assigned).DBS-70-400DBS Manual - Issued 8/l/95Page 3-51
~~L~IUI I rcuu-r I uyl a I II I III iyPermanent Call Forward Extension Software Version:CPC-All (all versions); CPC-B Version 3.1 or higherAddress: FF3 (ExtPort)# 43# (IO-69 or lOO=699)# DescriptionIf an extension is enabled for Permanent Call Forwarding (in address FF3 ExtPort# 41#), use this address to set another extension number as the target or “permanent call forwarding point” for the forwarded calls. In addition to regular extension numbers, the permanent call forwarding point can also be a System Speed Dial number (SSD), a Personal Speed Dial number (PSD), a hunt group pilot number, or an Attendant extension number. Programming To assign a Permanent Call Forwarding Point . . .FF3 (11144)# 43# (lo-69 or 1001699)# ff Extension Port Permanent Call Forwarding Point (Default=****; no extension assigned) lo-69 or l OO-699=Extension numbers, including attendants and hunt group pilot numbers. AUTO.90-99 or 900-909=PSD numbers. AUTO 00-89 or 000- 199=SSD numbers. To clear a Permanent Call Forwarding Point . . . FF3 (l-144)# 43# CONF ON/OFF + Related Programming Permanent Call Forward Type: FF3 (ExtPort)# 42# (0-3)# Hunt Group Pilot Numbers:FF4 3# (l-4)# l# (11-69 or 101-699)# System Speed Dial Numbers:FFlO l# (SSD)# (PhoneNo.)# Personal Speed Dial Numbers: FFlO 2# (ExtPort)# (PSD)# (PhoneNo.)# Page 3-52DBS Manual - issued 8/l/95DES-70-400
wcnon 4uwrruyrammlngbriaprer 3. txrerlslori rrogramrrimg [t-w) ML/MC0 Separation Software Version:CPC-All (all versions); CPC-8 Version 4.0 or higherAddress: FF3 (ExtPort)# 44## (0 or l)# DescriptionUse this address to enabie an extension for MC0 or ML key usage. The difference between ML (Multi-Line) and MC0 (Multi-Central Office) has to do with incoming calls. MC0 means multiple trunks can be received at the extension -- if you press a flashing FF key, you will get an incoming trunk .call. Calls from another extension will flash on the “EXT” LED (not through the FF key). ML, on the other hand, means you can receive either a trunk call or an extension call on an FF key, which will flash for either type of call. If this address is set to ML, each FF key must be individually enabled for ML/ MC0 using program address FF5 (ExtPort)# (Key)++ (FeatureCode)#. Programming FF3(l-144)#44## (0 or I)# Extension Par
VAU Hunting PrioritySoftware Version:CPC-All (all versions); CPC-B Version 5.0 or higherAddress: FF3 (ExtPort)# 45# (0 or l)# DescriptionUse this address to assign hunting priority to calls that ovefflow from a hunt group to the VAU. If hunting priority is assigned, a caller who hears the VAU message and then decides to dial back into the hunt group, will be placed before other calls that have just entered the hunt group queue. Without hunting priority, the caller loses his or her place in the queue and is placed in the last queue position upon re-entry intd the hunt group. ProgrammingIFF3 (1-l 44)# 45# (0 or l)# ft VAU Port NumberO=Calls transferred from the VAU do not receive priority treatment. l=VAU transfer ~rioritv. Related ProgrammingVAU Port Assignment: FF3 (ExtPort)# 47# (0 or l)# Page 3-54DBS Manual - Issued 8/l/95DBS-70-400
Section 400-ProgrammingChapter 3. Extension Programming (FF3) AEC Disconnect Software Version:CPC-All (all versions); CPC-6 Version 5.0 or higherAddress: FF3 (ExtPort)# 46# (0 or I)# DescriptionThe VB-43621A version of the AEC card can be set to provide a positive disconnect signal. Use this address to enable or disable the AEC disconnect signal on individual extension(s). If this option is enabled, analog extension ports will send a disconnect signal (open loop) upon hangup. Sending this signal allows quick disconnection f?om third-party voice mail systems. NOTE: This feature requires CPC-A 3.3 or higher, CPC-AII (all versions), or CPC-B 5.0 or higher. The address for CPC-A is FF3 (ExtPort)# 35#. ProgrammingLFF3 (I-144)# 46# (0 or I)## ft Extension PortO=Disa bled l=Enabled Related Programming SLT Disconnect Signal Duration:FFl 2# I# 3% (0-15)## DBS-70-400DBS Manual - Issued 8/l/95Page 3-55
Chapter 3. Extension Programming (FF3)Section 400-Programming VAU Port Assignment Software Version:CPC-All (ail versions); CPC-B Version 5.0 or higher bddress: FF3 (ExtPort)# 47# (0 or I)# I’ DescriptionThis program assigns a digital port as a VAU (Voice Announce Unit).Once a port is assigned as a VAU, the system treats that port as ifthe following changes have been made: l Offhook Signal (CO) is disabled - FF3 (ExtPort)# 7# O#.l Call Waiting/OHVA is disabled -- FF3 (ExtPort)# 8# O#.l Auto Pickup is enabled - FF3 (ExtPort)# 12# l#. lAll FF keys for the extension port are cleared - FF5 (ExtPort)# FFkey# CONF. ProgrammingFF3 (I-144)# 47# (Oorl)# ff VAU Port Numbero=off l=On (defines the port as a VAU) NotesApplicablk Call Types.When VAU is enabled for a port, the following call types will be routed to the first VAU message: @Trunk calls @Transferred trunk calls @Intercom calls *Transferred intercom calls. AU recalls will be routed to the second VAU message. VAU Port Assignment in CPC-A Versions.The address for VAU Port Assignment in CPC-A Version 3.3 or higher is FF3 (ExtPort)## 34# (0 or l)#. Page 3-56DES Manual - Issued 6/l/95DBS-70-400
Section 400-ProgrammingChapter 3. Extension Programming (FF3) Hot Dial Pad Software Version:CPC-All and CPC-B, Version 7.0 or higher Address:FF3 (ExtPort)# 48# (0 or I)# DescriptionThe dial pad on digital key phones can be designated as “hot” on an extension-by-extension basis. This feature allows the user to initiate a call without going ofIhook, by pressing any of the numeric keys O-9 (the “*” and “#I” keys are not “hot”). The extension’s dial pad can be “hot” under these conditions: lwhen the extension is idle. lwhen the extension is holding a call. lwhen the extension is holding a page. The extension’s dial pad cannot be “hot” under these conditions: lwhen an intercom or trunk call is ringing at the extension.l when the extension is on a call. ProgrammingFF3 (I-144)# 48# (0 or I)# ft Extension PortO=Eot Dial Pad is disabled. l=Hot Dial Pad is enabled. NotesPaging.The Hot Dial Pad feature cannot be used to initiate a page. Restriction.The Hot Dial Pad feature does not work on SLT phones. DES-70-400DBS Manual - Issued 8/l/95Page 3-57
t .Chapter 3. Extension Programming (FF3)Section 400-Programming Auto-Redial on Extensions Software Version:CPC-All and CPC-6, Version 7.0 or higherAddress: FF3 (ExtPort)# 49# (0 or I)# DescriptionUse this address to enable or disable the Auto-Redial feature on individual DBS extensions (DSLT or K-Tel only).Auto-Redial allows a telephone in the on-hook (idle) state to redial an internaI extension or an outgoing trunk call without going off-hook first. By default, Auto-Redial is enabled on all DSLT and K-Tel extensions. Auto-Redial is performed by pressing REDIAL when the phone is either on- hook (idle) or off-hook (dial tone). The DBS will automatically redial the last number dialed on that extension. Programming IFF3 (I-144)# 49#! (0 or I)# tt Extension PortO=Auto-Redial is disabled. l=Auto-Redial is enabled. NotesRestrictions.Auto-Redial wilI not work with the following:. SLTs. OPX. API. Voice Mail. Door Phones. Aato-Rediaf Afler a System Res&If Auto-Redial is attempted after a system reset, and neither a CO calI nor an extension calI has been made since the reset, the caller will hear intercom busy tone. Page 3-58DBS Manual - Issued 811195DBS-70-400