Home
>
Panasonic
>
Communications System
>
Panasonic Cpc+AII/B Digital Business System Release Notes Manual
Panasonic Cpc+AII/B Digital Business System Release Notes Manual
Have a look at the manual Panasonic Cpc+AII/B Digital Business System Release Notes Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 10737 Panasonic manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Chapter 1. System Programming (FFi)Section 400-Programming Red Alarm Detection Software Version:CPC-6 Version 4.0 or higherAddress: Master Cabinet: FFl 8# 4# 4# 2# 1# (015)# Slave Cabinet:FFI 8# 4## 5# 2# 1# (015)# DescriptionThe default value for this parameter is determined by network specifications. It should not be changed. If a red alarm occurs, the “CFA” LED on the Tl card lights. Also, if the Red Alarm Relay (FFl 8# 4# 4/5# 4# 2#) is enabled, the alarm relay on the Tl MDF card closes. Programming I FFl 8# 4# (4 or 5)# 2# l# (O-5)# $$ 4=Master Cabinet0=4 5=Slave Cabinet1=6 2=8 3=10 4=12 5=14 Related ProgrammingRed Alarm Counter: FFl 8# 4# (4 or 5)# 3# 3# (0-9000)#Red Alarm Relay: FFl 8# # (4 or 5)# 4# 2# (0 or l)#Red Alarm FF Key: FF5 (ExPort)# (Key)# CONF (103# or 123#)#Page l-l 66 DBS Manual - Issued 8/l/95DBS-70-400
Section 400-ProgrammingChapter 1. System Prcgramming tFF1)Yellow Alarm Detection Software Version: CPC-B Version 4.0 or higher Address:Master Cabinet: FFl 8# 4# 4## 2# 2# (0-15)# Slave Cabinet:FFl 8## 4# 5# 2# 2# (0-15)# DescriptionDetermines how long a yellow alarm signal must be on before the system detects a yellow alarm. When a yellow alarm occurs, the “YEL” LED on the Tl card lights. Also, if the Yellow Alarm Relay (FFl 8i: 4# 4/5n” 1# l#) isenabled, the alarm relay on the TI MDF card closes. Programming1I FFl 8# 4## (4 or 5)# 2# 2# (045)# 7$ I 4=Master CabinetYellow Alarm Detection timer setting 5=Slave Cabinet Default: 1 (50 ms) fsee tabie below!Table I-49. Yellow Alarm Detection timer values I Setting ! Value ( 150 ms 41 200 msI 1 51250ms [ 3OOms I350 ms 1 400 ms I450 ms 10500 ms 11550ms 12600 ms 13650 ms 14,700 ms 15750ms DBS-70-400 DBS Manual- Issued 8/l/95Page1 -167
Chapter 1. System Programming (FFl)Section 400-Programming Related ProgrammingYellow Alarm Send: FFl 8# 4#/ (4 or 5)# l# 7# (0 or l)# Yellow Alarm Recovery:FFl 8# 4# (4 or 5)# 2# 3# (0-15)#Yellow Alarm Counter: FFl 8# 4## (4 or 5)# 3# 6# (0-9000)#Yellow Alarm Relay: FFl 8# 4# (4 or 5)# # l# (0 or l)# NotesPower-Cycling Requirement.For changes to this parameter to take effect, the system must be turned off, then back on. Page 1-168 DBS Manual - Issued 8/l/95DBS-70-400
Section 400-ProgrammingChapter 1. System Programming (FFI) Yellow Alarm Recovery Software Version:CPC-B Version 4.0 or higherAddress: Master Cabinet: FFl 8# 4## 4## 2# 3# (0115)# Slave Cabinet:FFl 8# 4#I 5# 2# 3# (0115)# Description ProgrammingDetermines how long the DBS tries to recover from a yellow alarm before it re-syncs the Tl trunk. FFl 8# 4# (4 or 5)# 2# 3# (0115)# 7f 4=Master CabinetYellow Alarm Recovery timer setting 5=Slave CabinetDefault: 1 (10 rns) (see table below)I Table l-50.Yellow Alarm Recovery timer values Setting 0 Value Orlis I 11 1omsI 220 ms 330 ms 440 ms 550 ms 660 ms 770 ms 880 ms 990 ms 10110 ms 11120 ms 12130 ms 13140 ms 14150 ms 15160 ms DBS-70-400DBS Manual - Issued 8/l/95Page 1-169
Chapter 1. System Programming (FFi)Section 400-Programming Related ProgrammingYellow Alarm Send: FFl 8# 4## (4 or 5)# l# 7# (0 or l)#Yellow Alarm Detection: FF1 8# # (4 or 5)# 2# 2# (0-15)##Yellow Alarm Counter: FFl 8# 4# (4 or 5)# 3# 6# (0-9000)#Yellow Alarm Relay: FFl 8# 4# (4 or 5)# 4## l# (0 or l)# NotesPower-Cycling Requirement.For changes to this parameter to take effect, the system must be turned off, then back on.Page l-l 70 DBS Manual - Issued 8/i/95DBS-70-400 _
Section 400-ProgrammingChapter 1. System Programming (FFl) Other Alarms Detection Software Version:CPC-B Version 4.0 or higherAddress: Master Cabinet: FFl 8# 4## 4# 2# 4# (0-15)# Slave Cabinet:FFl 8# 4# 5# 2# 4# (0015)# DescriptionDetermines how long an out-of-frame (OOF), loss of signal, sync loss, or AIS signal must be on before the system generates an alarm. If an OOF, Sync Loss, or AIS alarm occurs, a corresponding LED on the Tl card lights. (Sync Loss alarms light the “SLIP” LED.) The alarm relay on the Tl MDF card will also close if the corresponding relay parameter is enabled. Programming II FFI 8# 4# (4 or 5)# 2# 4# (0-15)# 7t 4=Master CabinetOther Alarms Detection timer setting 5=Slave CabinetDefault: 1 (250 rns) (see table below) Table l-51. Other Alarms Detection timer values Setting 0 Value Oms I 250msI 2I 500 ms1 I 1 3I 750 ms1 4 1000 ms 51250 ms I I 6I 1500 ms I 1750msI 81 2000 ms I 2500 msI 10I 3000 ms I 3500 ms 124000ms 134500ms 145000msI 15I 5500 ms1 DBS-70-400DBS Manual - Issued 8/l/95Page l-171
ChapterRelated Programming Other Alarms Recovery:FFl 8# 4## (4 or 5)# 2# 5# (0-15)# NotesPower-Cycling Requirement.For changes to this parameter to take effect, the system must be turned off, then back on. Page 1-l 72DBS Manual - issued 8/l/95.DBS-70-400
Section 400-ProgrammingChapter 1. System Programming (FFl) Other Alarms Recovery Software Version:CPC-B Version 4.0 or higherAddress: Master Cabinet: FFl 8# 4#I 4# 2# 5# (O-15)# Slave Cabinet:FFl 8## 4# 5# 2# 5# (O-15)# DescriptionDetermines how long the DBS tries to recover from an Out-Of-Frame (OOF), Loss of Signal, Sync Loss, or AIS alarm before it re-syncs the Tl trunk. Programming I FFI 8# 4## (4 or 5)# 2# 5# (0115)# 7 4=Master CabinetOther Alarms Recovery timer setting 5=Slave Cabinet Default: 1 (250 ms) (see table below) Table I-52. Other Alarms Recovery timer values SettingValue 0Oms 1250 ms 2500 ms 3750 ms 41000 ms 51500 ms 62000 ms 72500 ms 83000 ms 94000 ms 105000 ms 116000 ms 127000 ms 138000 ms 149000 ms 1510000 ms Related ProgrammingOther Alarms Detection: FFl 8# 4## (4 or 5)# 2# 4## (0-15)# NotesPower-Cycling Requirement.For changes to this parameter to take effect, the system must be turned off, then back on. DBS-70-400DBS Manual - issued 8/l/95Page l-173
bikiprer I. 3ysrerr1 rrogrammwg r I)3ection 4uwrrogrammlngFrame Loss Counter Software Version:CPC-B Version 4.0 or higherAddress: Master Cabinet: FFl 8# 4# 4## 3# 1# (019000)# Slave Cabinet:FFl 8# 4# 5# 3# 1# (O-9000)# DescriptionDetermines how many frame losses occur before a Frame Loss Alarm FF key is lit. The FF key lights when the counter exceeds the specified number within a 24-hour period. For instructions on programming Tl alarm keys, see the TI Reference Manual (Section 500). Programming FFl 8# 4#/ (4 or 5)# 3# l#(019000)# f 4=Master Cabinet 5=Slave Cabinet Number of Frame Losses that occur within a 24-hour period before a Frame Loss Alarm FF key is lit Default: 9000 Related ProgrammingFrame Loss Relay: FFl’ 8# 4# (4 or 5)# 4# 4# (0 or l)#Page l-l 74 DBS Manual - issued 8/l/95DBS-70-400
Section 400-ProgrammingChapter 1. System Programming (FFl) Slip Counter Software Version:CPC-B Version 4.0 or higherAddress: Master Cabinet: FFl 8# 4# 4# 3# 2# (0-9000)# Slave Cabinet: FFl 8# 4#I 5# 3# 2# (0-9000)# DescriptionDetermines how many slips occur before a Slip Alarm FF key is lit. (“Slips” are losses of data bits due to framing errors.) The FF key lights when the counter exceeds the specified number within a 24-hour period. This parameter also determines the number of slips that can occur before the system switches to the next clock source, at which time the slip error counter for the first clock source is reset, and all phone calls in progress are disconnected. It takes 20 seconds for the Tl to reboot. For instructions on programming Tl alarm keys, see the Tl Reference Manual (Section 500). Programming I FFl 8# 4# (4 or 5)# 3# 2# (O-9000)# f 4=Mas ter Cabinet 5=Slave Cabinet Number of Slips that must occur within a 24-hour period before a Slip Alarm FF key is lit Default: 9000 Related Programming Sync Source 1:FFl 8# 4# l# 2# (l-3)#Sync Source 2: FF1 8# # l# 3# (0-3)#Sync Source 3: FFl 8# 4# l# 4# (0-3)#Slip FF Key: FF5 (ExtPort)# (Key)# CONF (102# or 122#)# DBS-70-400DBS Manual - Issued 8/l/95Page 1-175