Home
>
Panasonic
>
Communications System
>
Panasonic Cpc+AII/B Digital Business System Release Notes Manual
Panasonic Cpc+AII/B Digital Business System Release Notes Manual
Have a look at the manual Panasonic Cpc+AII/B Digital Business System Release Notes Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 10737 Panasonic manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Chapter 1. System Programming (FFl)Section 400-Programming Tl Trunk Type Emulation Software Version:CPC-6 Version 4.0 or higherAddress: FFl 8# 4# 6# (Trunk)## 1# (OS)# DescriptionDetermines the type of trunk signaling that each Tl channel emulates (E&M by default). Programming I Notes FFl 8# 4## 6# (1164)# l# (013)# f+ Trunk Number (l-64)O=Loop start 1 =ireserved for-future use) 2=Ground Start (used for ground start emulation) 3=E&M Power-Cycling Requirement.For changes to this parameter to take effect, the system must be turned off, then back on. Ground Start Requirement.If your system uses Tl COP (Central Office Protocol) Version 1.1 or 1.2, it must be ,upgraded to Version 1.4 or higher if you wish to use the “Ground Start” setting.Page l-l 88 DBS Manual - Issued 8/l/95DBS-70-400
Section 400-ProgrammingChapter 1. System Programming (FFl ) DID/DNS Software Version:CPC-B Version 4.0 or higherAddress: IFFi W 4# W (Trunk)# 2# (O-2)# DeskiptionUse this address to enable trunks for DID or DNIS calls.l If DID is seiected, the system will use the DID Numbers Table (see FFl 8# 3#) to detemine which extension(s) will receive the DID call.l If DNTS is selected (available only with Tl interface), the system will use the DNIS Numbers Table (see FFl 8# 4# 7#) to determine which extension(s) will receive the DNIS call. The DID Numbers Table can be used for DID or DNIS. Therefore, ifall 500 entries in the DNIS Numbers Table are filled, a Tl channel can be set to DID, and DNIS service can still be used. Programming i FFI 6# 4# 6# (1-64)# 2# (0-2)# f4 Trunk Number (l-64)O=Neith& DID nor DNIS is used. l=DID is used. 25DNIS is used. Related ProgrammingInbound DID DialNumbers: FFl 8# 3# (DIDNo.)# (ExtNo.)# DNIS Number Setting: FFl 8# # 7# (DNISNo.)# (ExtNo.)# DIDIDNIS Flexible Ringing Assignments: FFl 8# (5# or 6#) @lD/DNIS No.)# (ExtNo.)# (OOOO[OO]-l l l l [ 1 l])# NotesDigit Length Requiremen&The DBS only supports 4digit DIDAlMS numbers. CO RequirementWhen the CO sends a DIDIDNIS call to the DBS, it first receives a “wink” signal &om the DBS before sending the digits.Once the wink is received, the CO should wait at least 200 ms before sending the digits. Power-C’chg Requirement.For changes to this parameter to take effect, the system must be tumed off, then back OIL DBS-70-400 ;.. DBS Manual - Issued 8/l/95Page l-1 87
Chapter 1. System Programming (FFl)Section 400-Programming Soha= k~;xi~n:CPC-B Version 4.0 or higherAddress: #-I T r;a# 4# 6# (Truwk)# 3# (012)# DescriptionDetermines the signaling class used by Tl channels on outgoing calls (Immediate Start by de&&).’ Programming FFI 8# 4# 6# (144)# 3# (0-2)# f Trunk Number (l-64)O=Immediate Start. l=Wink start. 2=Dial Tone Start. CO Requirement.The Outgoing Type setting must match what is ordered f?om the CO.. Power-Cycling Requirement.For changes to this parameter to take effect, the system must be turned off, then back on. Page 1-188DBS Manual - Issued 8/l/95DBS-70-400
Section 400-Programming Chapter 1. System Programming (FFl) Incoming Signaling Type Software Version:CPC-8 Version 4.0 or higherAddress: FFI 8# 4# 6## (Trunk)# 4#I (0 or I)# DescriptionDetermines the signaling class used by Tl channels on incoming calls (Immediate Start/Ringdown by default). Programming r Notes FFI 8# 4# 6# (I-64)# 4# (0 or l)# f+ Trunk Number (l-64)O=Immediate Start/ Ringdown. l=Wink Start. CO Requirement.The Incoming Type setting must match what is ordered from the CO. Power-Cycling Requirement.For changes to this parameter to take effect, the system must be turned off, then back on. DBS-70-400DBS Manual - Issued 8/l/95Page 1-189
Chapter 1. System Programming (FF’l)Section 400-Programming Trunk Mode Software Version:CPC-6 Version 4.0 or higherAddress: FFI 8# 4#I 6# (Trunk)# 5# (0 or l)# DescriptionDetermines whether Tl channels are used for only outgoing calls, or for both incoming and outgoing calls. Programming I FFI 8# 4# 6# (l-64)# 5# (0 or l)# f+ Trunk Number (l-64)O=Incoming and Outgoing. l=Outgoing only. NotesPower-Cycling Requirement.For changes to this parameter to take effect, the system must be turned off, then back on. Page l-190DBS Manual - Issued 8/l/95DBS-70-400
Section 400-ProgrammingChapter 1. System Programming (FFl) Robbed Bit Setting Software Version:CPC-B Version 4.0 or higherAddress: FFl 8# 4## 6# (Trunk)# 6# (0 or l)# DescriptionThe Robbed Bit Setting determines if AB or ABCD signaling is used. AB/ABCD signaling robs bits from the Tl channels, and uses those bits to transmit signaling information. SF (SuperFrame) normally uses AB signaling; ESF (Extended SuperFrame) normally uses ABCD signaling. Programming I FFl 8# 4# 6# (l-64)# 6# (0 or l)# i(lr Trunk Number ( l-64)- O=Robbed Bit Off (AB/ABCD signaling not used) l=Robbed Bit On (AB/ABCD signaling is used) NotesYower-Cycling Requirement.For changes to this parameter to take effect, the system must be turned off, then back on. DBS-70-400DBS Manual - Issued 8/l/95Page 1-191
Chapter 1. System Programming (FFl)Section 400-Programming Incoming Dialing Method Software Version:CPC-B Version 4.0 or higher Address:FFl 8# 4# 6# (Trunk)# 7# (0 or l)# DescriptionDetermines whether the system expects dial-pulse or DTMF digits for incoming DID or DNIS calls over the Tl. Programming I FFl 8# 4# 6# (1164)# 7# (0 or l)# ff Trunk Number (l-64)O=Dial-Pulse (10 PPS) l=DTMF NotesPower-Cycling Requirement.For changes to this parameter to take effect, the system must be turned off..then back on. Hardware Requirement.An MFR card is required for DID/DNIS if DTMF signaling is used.Page l-l 92 DBS Manual - Issued 8/l/95DBS-70-400
Section 400-ProgrammingChapter 1. System Programming (FFl) Dial Tone Transmission Software Version: CPC-B Version 4.0 or higher.Address: FFl 6# 4# 6# (Trunk)#I W (0 or l)# DescriptionThis address is reserved for future use. DBS-70-400DBS Manual - Issued 8/l/95Page 1-193
Chapter 1. System Programming (FFl)Section 400-Programming Busy Tone Transmission Software Version: CPC-B Version 4.0 or higherAddress: FFl 8# 4# 6# (Trunk)# 9# (0 or l)# DescriptionThis address is reserved for future use. Page 1-194DBS Manual - Issued 8/l/95.DBS-70-400
Section 400-ProgrammingChapter 1. System Programming (FFi) Dial Tone Receive Software Version:CPC-B Version 4.0 or higherAddress: FFl 8# 4# 6# (Trunk)# lO# (0 or l)# DescriptionDetermines whether dial tone is transmitted from the DBS Tl channel to DBS stations. Set this address to “On” only if the far end does not provide Tl dial tone. Programming I I FFl 8# 4# 6# (l-64)# 1 O# (0 or l)# f+ Trunk Number (1-64)O=Off l=On NotesOr&ring Tones From Carrier.If a carrier is supplying Tl services, always order Dial Tone and Ringback Tones from the carrier. DBS-70-400DBS Manual - Issued 8/l/95Page 1-195