Home > Panasonic > Communications System > Panasonic Cpc+AII/B Digital Business System Release Notes Manual

Panasonic Cpc+AII/B Digital Business System Release Notes Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Panasonic Cpc+AII/B Digital Business System Release Notes Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 10737 Panasonic manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    Page
    of 1046
    							Chapter 1. System Programming (FFl)Section 400-Programming
    Ringback Tone Transmission
    Software Version:
    CPC-B Version 4.0 or higher
    Address: 
    FFl 8## 4#I 6# (Trunk)# 11# (0 or l)#DescriptionDetermines whether 
    ringback tone is transmitted from the DBS Tl channel to
    the CO.Set this address to “On” only if the far end does not provide 
    ringback tone.
    Programming
    I1
    FFI 8# 4# 6# (l-64)# 11# (0 or l)#
    4/+Tmnk Sumber 
    i l-64)&Off
    l=On
    NotesOr&ring Tones From Currier.If a carrier is supplying Tl services, always
    order Dial Tone and 
    Ringback Tones from the carrier.
    Page l-196DBS Manual 
    - Issued 8/l/95DBS-70-400 
    						
    							Section 400~ProgrammingChapter 1. System Programming (FFl)
    DNIS Number Setting
    Software Version:CPC-B Version 4.0 or higherAddress: 
    FFl 8## 4## 7# (DNISNo.)# (ExtNo.)#
    DescriptionUse this address to assign DNIS number(s) to extension(s).
    lUp to 500 different DNIS numbers can be assigned.
    lOne DNIS number can be assigned to multiple extensions (this takes up
    only one entry in the 500 available entries).
    lOne extension can have multiple DNIS numbers assigned to it. (The
    number of entries taken up is equal to the number of DNIS numbers
    assigned to the extension.)
    Programming
    I
    I
    FFl 8# 4# 7# (0000-9999)# (1 O-69 or 1009699)#
    f+
    4-digit DNIS Number
    Extension NumberRelated Programming .
    Multiple 
    DID/DNIS: FFl 2# l# 32# (0 or l)#
    DlD/DNIS (enabling trunks for): FFl 8# # 6# (Trunk)# 2# (0-2)##
    DNIS Flexible Ringing Assignments:FFl 8# 6# (DNISNo.)# (ExtNo.)#
    (0000[00]-llll[ll])#Extension Numbers: FF3 
    (ExtPort)# l# (ExtNo.)#
    NotesDZVZ,S Requiremenf.
    DNIS is available only with the Tl interface.
    Digit Length Requirement.The DBS supports 4-digit DNIS numbers with
    either dial pulse or DTMF transmission.
    DlVZ,S Ring ControLRinging for the DNIS number at the assigned
    extension(s) is controlled by the next address 
    (FFl 8# 6#).
    DBS-70-400DBS Manual - Issued 8/l/95Page l-197 
    						
    							Chapter 1. System Programming (FFl)Section 400-Programming
    DlDlDNlS Flexible Ringing Assignments
    Sofbvare Version:CPC-B Version 5.0 or higherAddress: for DID:
    FFl 8# 5# (DIDNo.)# (ExtNo.)# (OOOO[OO]-llll[Sl])#
    for DNIS:
    FFl 8# 6# (DNISNo.)# (ExtNo.)# (OOOO[OO]-llll[ll])#
    DescriptionThis address allows you to enable or disable ringing for specific DID/DNTS
    numbers during Day, Night and Night 2 modes. This also applies to delayed
    ringing.
    Note: The DID/DNIS number must already be assigned to an extension
    number before you can assign it for flexible ringing. See 
    FFl 8# 3# (for
    DID) and FFl 8# 4# 7# (for DNIS).
    Programming
    FFl 8# (5 or 6)# (XXXX)# (lo-69 or lOO-699)#
    f + +
    (OOOO[OO -llll[ll])##
    1
    5=DID4-digit DID orExtension NumberRing Settings
    6=DNTSDNIS numberthat will receive(see table below)
    (must alreadyringing
    be assigned toO=Disabled
    an extension, or1 =Enabled
    the system won’t
    accept the number
    here)
    Default: Ringing enabled;
    Delayed ringing disabled.
    L
    Table l-53. DIDIDNIS Flexible Ring settings in different CPC-B versions
    Ring Control
    for each digit
    setting
    1st digit
    2nd digit
    3rd digit
    4th digit
    5th digit
    6th digit
    CPC-B
    Version 5.0 to 6.1
    Day ring
    Night ring
    Delayed Day ring
    Delayed Night ring
    [not available]
    [not available]
    Default Setting:1100111000 CPC-B
    Version 7.0 or higher
    Day ring
    Night ring
    Night 2 ring
    Delayed Day ring
    Delayed Night ring
    /Delayed Night 2 ring
    Related ProgrammingDelayed Ring: 
    FFl 2# l# 23# (0 or l)#Page l-l 98
    DBS Manual - Issued 8/l/95D BS-70-400 
    						
    							Section 400-Programming
    Chapter 1. System Programming (FFl)CO Delayed Ring Timer: 
    FFl 3# 26# (0-15)#Inbound DID Dial Numbers: 
    FFl 8# 3# (D1DNo.H (ExtNo.)#
    DID/DNIS (enabling trunks for): FFl 8# 4# 6# (Trunk)# 2# (0-2)##
    DNIS Number Setting: FFl 8# # 7# (DNISNo.)# (ExtNo.)#
    NotesDelayed Ring Timing.Timing for DID/DNIS delayed ringing is controlled
    by the CO Delayed Ring Timer 
    (FFl 3# 26# O-l%).
    DBS-70-400DBS Manual - issued 8/l/95Page l-199 
    						
    							Chapter 1. System Programming (FFl)Section 400-Programming
    .
    Tl Trunk Closure
    Software Version:WC-B Versions 5.0 to 6.02Address: Master Cabinet: 
    FFl 8# 7# 1# (l-4)# (118)# (0 or l)#
    Slave Cabinet:FFl 8# 7# 2# (l-4)# (1,8)# (0 or l)#
    DescriptionIn CPC-B Versions 5.0 to 6.02, use this address to facilitate Fractional Tl,
    where not all of the 24 available channels on the Tl card are used.
    Lf the trunk ports on the highest-numbered analog trunk card are divided
    between 
    Tl and analog, use this address to close the trunk ports dedicated to
    Tl -- and open the trunks to be used for analog. (see illustration below for an
    example)
    Use the 
    “Number of Tl Channels” address (FFl g# 4# 4/5# l# 2#) to tell the
    system how many channels you want to use. The system will automatically
    assign one analog trunk port for each 
    Tl channel used. Channel #l
    automatically uses the highest-numbered port on the highest-numbered trunk
    card; Channel 
    #2 uses the next highest port; etc.Figure 1-3. Trunk Cl
    we Eramnle in a
    Trunk Cards (each card has 8 trunk ports, Trunk Cards (each card has 8 trunk ports,
    numbered as shown) numbered as shown)
    Card 1
    1
    Ca;d2/I[
    22
    3
    3
    44
    5
    5
    6
    6
    77
    8In this example, the following was In this example, the following was
    programmed: programmed:
    Trunk Configuration set to 
    “Tl and Analog” (see FFl 8# 4## 4# 1# l#).Number of 
    Tl Channels set to “12” (see FFl 8# 4## 4# l# 2#).
    Tl Trunk Closure set Tl trunks 5-8 on Card 3 to “Close”:
    FFl 8# 7# l# 3# (5 thru 8)# l#Page l-200
    DBS Manual - Issued 8/l/95DBS-70-400 
    						
    							Section 400-ProgrammingChapter 1. System Programming (FFl)
    Programming
    rI
    FFl 8#7#
    l=Master Cabinet
    2=Slave Cabinet
    Trunk SlotT&k PortO=Open
    on Cardl=Close
    Related Programming
    Trunk Configuration:FFl 8# 4## (4 or 5)# l# l# (0 or l)#Number of 
    Tl Channels: FFl 8# 4## (4 or 5)# l# 2# (0-24)#
    Trunk Circuit Type: FF2 
    (Trunk)# 21# (0-3)#
    NotesLoop-Start Card Version Requirement.This Tl Trunk Closure address
    can only be used with the VB-435 
    10A or VB-43511A versions of the loop-
    start card.
    CPC-B Versions Beginning With 6.03.The Tl Trunk Closure address is
    no longer present. Instead, simply 
    use the Trunk Circuit Type address (FF2
    Trunk# 21#) to assign trunk ports as Loop Start, Ground Start, DID or Tl.
    DBS-70-400DBS Manual - Issued 8/l/95Page l-201 
    						
    							2. Trunk Programming (FF2)
    Use the FF2 programming addresses in this chapter to set parameters for the
    CO trunks of the DBS system.
    Most of these FF2 addresses require a trunk number and/or extension port
    entry. The acceptable range of trunks/extension ports varies according to the
    configuration of your DBS system. In this chapter, the range used for trunks
    is l-64. which is the maximum available number of trunks in a DBS 96 +
    DBS 96 system with a CPC-B card. The range used for extension ports is
    1-144, which is also the maximum in a DBS 96 + DBS 96 with CPC-B.
    For more information, 
    see Section 300-Installation.
    This chapter covers the following FF2 program addresses:
    FF Key AddressTopic
    Page
    FF2 (Trunk)# I# (O-l)#Trunk Port Operation2-3
    FF2 (Trunk)# 2% (O- l)#DTMF/Pulse Dialing for Trunks
    FF2 (Trunk)# 3# (O-l)#Pooled Trunk Access for Group “9”
    FF~ (TnnrH# 4+~ thru 9# (o-l)# Pooled Trunk Access for Groups “81-86”
    12-4 ’
    2-5
    2-6-,
    FF2 (Trunk)# lo# (l-2)#1 Trunk Port Type1 2-7
    J?F2 (Trunk)# 11# (0-I)#DISA Auto Answer1 2-8
    FF2 VrunH# 12# (Ext.Pon)#Private Trunk LineI 2-9
    FF2 (Trunk)#’ 13# (0-l)#
    FF2 (Trunk)# 14# (0-l)#
    Automatic Pause for PBX Line
    Dial Tone Detection2-102-11
    FF2 (Trunk)# 1% ( I-3)#
    FF2 (Trunk)# 16# (0- I)#
    Outbound DTMF Signal Duration for Auto-Dialed
    Digits
    Unsupervised Trunk Conference
    1 FF2 (Trunk)# 17# (0-l)#1 Inbound Ring Pattern12-14 1II
    1 Trunk Disconnect Detection Timer
    IJYF2 (Trunk)# 18# (0-15)#t 2-15 1I
    FF2 (Trunk)# 19# HHMM#DISA Start Time1 2-16
    1 FF2 (Trunk)# 20# HHMM#I DISA End Time12-17 I
    FF2 (Trunk)# 21# (0-4)#Trunk Circuit Type (CPC-AII/B)2-18
    FF2 (Trunk)# 22# (0-l)#DID Immediate or Wink Start(CPC-B only)2-21
    FF2 (Trunk)# 23# (0-15)#Wink Start Timer (UC-B only)1 2-22
    FF2 (Trunk)# 24# (O- 15)#Time Out for Dialed DID Digits(CPC-B onb)2-23
    FF2 (Trunk)# 25# (O- 15)#DID Interdigit Timeout (CPC-B only)2-24
    FF2 (Trunk)# 26# (4-8)#Trunk Port Class (WC-B only)2-25
    DBS-70-400DBS Manual - Issued 8/l/95Page 2-l 
    						
    							Page 2-2
    DBS Manual - Issued 8/l/95*DE!%70-400
    ‘\ 
    						
    							Trunk Port Operation
    Software Version: All VersionsAddress: FF2 
    (Trunk)# l# (0 or l)#
    DescriptionUse this feature to put a CO trunk in service or “busy it out”.
    ProgrammingFF2 
    (li”” 1# (0 y l)#
    Trunk NuniberO=Place trunk in service.
    l=Busy-out the trunk.
    NotesPrecaution on Putting Lines Out of Service.If you busy-out a trunk, an
    incoming caller on that trunk will still hear ringing, even though the trunk is
    not functional.
    D BS-70-400DBS Manual - Issued 8/l/95Page 2-3 
    						
    							DTMF/PuIse Dialing for Trunks
    Software Version: All VersionsAddress: FF2 (Trunk)# 
    2# (0 or l)#
    DescriptionUse this feature to set a trunk for DTMF or pulse dialing (10 pulses per
    second).
    Programming
    I
    Trunk NumberO=DTMF
    l=Pulse dialing (10 pps)
    Notes-Door Box Adapter Setting.CO trunk ports used for Door Box Adapter
    Sensors should be set for “Pulse dialing”.
    Page 2-4DBS Manual - Issued 8/l/95DBS-70-400 
    						
    All Panasonic manuals Comments (0)

    Related Manuals for Panasonic Cpc+AII/B Digital Business System Release Notes Manual