Home
>
Panasonic
>
Communications System
>
Panasonic Cpc+AII/B Digital Business System Release Notes Manual
Panasonic Cpc+AII/B Digital Business System Release Notes Manual
Have a look at the manual Panasonic Cpc+AII/B Digital Business System Release Notes Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 10737 Panasonic manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
![Page 107
Chapter 3. Cabinet InstallationSection 300-Installation
4.Attach the mounting brackets to the four comers of the back side of the
cabinet.
Figure 3-2. Cabinet mounting bracket
Figure 3-3. Cabinet wa
5.Install four screws in the wall studs according to the dimensions given in
Figure 3-3. (Note that the width dimension is different for the DBS 40.)
.The screws are used to attach the mounting brackets to the wall. The
screws should protrude from the wall
5/16 in.
mountinp
Stud\
(DES 40)
6.Hang the cabinet...](http://img.usermanuals.tech/thumb/58/85067/w64_panasonic-dbs-40-72-96-rel-notes-ver-8_d-106.png "Page 107
Chapter 3. Cabinet InstallationSection 300-Installation
4.Attach the mounting brackets to the four comers of the back side of the
cabinet.
Figure 3-2. Cabinet mounting bracket
Figure 3-3. Cabinet wa
5.Install four screws in the wall studs according to the dimensions given in
Figure 3-3. (Note that the width dimension is different for the DBS 40.)
.The screws are used to attach the mounting brackets to the wall. The
screws should protrude from the wall
5/16 in.
mountinp
Stud\
(DES 40)
6.Hang the cabinet...")
Chaoter 3. Cabinet Installation Section 300~Installation Installation F, 1.With the lettering on the card pointed up, position the card within the slot guides. (See Figure 3-7.) 2.Hold the card on the top and bottom edges with both hands and carefully push the card into the slot. 3.When the connector at the far end of the card touches the corresponding connector on the backplane, press the card in until it is firmly seated. rre 3-7. Printed circuit card installation Zard- .abel * The extension card installed in this slot must be digital. #The MFR card can be installed in the CPC slot of slave cabinets.3-8 . DBS Manual - Issued 8/l/95DES-70-300
Section 3004nstallationChapter 3. Cabinet Installation Battery- Guidelines lThe DBS 40 uses two 12-volt batteries; the DBS 72 and 96 use four 6-volt batteries or two 12-volt batteries. The following table includes the part numbers for the battery packages. Table 3-I.Battery backup packages for the DBS 40, 72, and 96SystemBattery Backup Part No. DBS 40VB-43130 (some systems may be equipped with VB-2450A-2P) DBS 72 and 96 VB-43 130 (some systems may be equipped with VB-2650-2P) lThe backup batteries are connected in a series circuit, using cables provided with the DBS. lWith maximum traffic, the backup batteries last up to 40 minutes for the DBS 40 and 72, and up to 30 minutes for the DBS 96. lThe backup batteries should be replaced about every 3 years. RECYCLE THE PRODUCT YOU HAVE PURCHASED MAY CONTAIN SEALED LEAD ACID BATTERIES WHICH ARE RECYCLABLE. AT THE END OF THEIR USEFUL LIFE, UNDER VARIOUS STATE AND LOCAL LAWS, IT IS ILLEGAL TO DISPOSE OF THESE BATTERIES INTO YOUR MUNICIPLE WASTE STREAM. PLEASE CALL l-800-SAV-LEAD FOR INFORMATION ON HOW TO RECYCLE THESE BATTERIES. DBS-70-300DBS Manual - Revised S/22/973-9
Chapter 3. Cabinet Installation Section 300~Installation Installation for the DBS 40 1.Place one battery in the top tray of the battery compartment, the other battery in the bottom tray. Fi, location. DBS 40Batteries 2.Connect the positive cable (red) to the + terminal of the top battery. 3.Connect the connecting cable (white) to the - terminal of the top battery. 4.Connect the negative cable (blue) to the - terminal of the bottom battery. 5.Connect the connecting cable (white) from the top battery to the + terminal on the bottom battery.3-l 0 DBS Manual - Issued 8/l/95DBS-70-300
Section 300~lnstaaationmamer 3. C;atmet lnstallatlon Installation for the DBS 72 and 96 1.Slide the battery compartment out and place the batteries inside the tray. Figure3-9. Remove Screwsand Slide Battery Tray Out 2.Connect the positive cable (red) to the + terminal on the fist battery. 3.Connect the negative cable (blue) to the - terminal on the last battery. 4.Connect the remaining positive and negative terminals with the white connection cables, as shown in Figure 3-10. DBS-70-300DBS Manual - Issued 8/1’/953-11
Chapter 3. Cabinet lnStah3tiOnSection 3004nstallation Figi3-10. Battery pack connection, DBS 72 and 96 RedConnection Cable Front Negative Four G-Volt Batteries (Older Version) VB-265012PWhite Connection Cables - Red Connection Cable \*cBack Positive Front Negative ‘Fwo 1 O-Volt Batteries (Newer Version) VB-43130 3-12Dl3S Manual - Issued 8/l/95cm-70-300
3emon yuu-lnsraiiatlon Key Phone Wall Mounting Gnapter 3. Cabinet Installation DBS key phones can be modified for wall mounting by reversing the wall- mount adaptor on the bottom of the phone. The wall-mount adaptor includes a small hole for attaching the phone to a screw inserted in the wall. 1.Place the bottom edge of the telephone on a desk or other hard surface. 2.Press the wall-mount adaptor down until it detaches from the phone (Figure 3- 11).Figure 3-11.UdflDtO?’removal Wall-Mount Adaptor DBS-70-300DBS Manual - Issued 6/l/953-l 3
Chapter 3. Cabinet InstallationSection 300~Installation Figure 3-12.Wall-mount adaptor replacement igure 3-13. Handset Guide 3.Turn the wall-mount adaptor around and re-attach it to the phone.. LI.Remove the handset guide with a small screwdriver, turn it over, and reinsert it into the phone. t guide insertion for wal 7-m-r n3znting, key phor I13-l 4 DES Manual - Issued 8/l/95DBS-70-300
Section 3004nstallationChapter 3. Cabinet Installation DSLT Wall Mounting - Digital Single-Line Telephones (DSLTs) can be modified for wall mounting by removing the desk stand and mounting it on the bottom of the phone. The back of the DSLT and the desk stand include slots for attaching the phone to a screw inserted in the wall. 1.Press the stand releases in toward the middle of the phone to release the desk stand (Figure 3- 14). Figure 3-14. Desk stand removal for DSLT wallmountinpDBS-70-300 DBS Manual - Issued 8/1’/953-15
Chapter 3. Cabinet InstallationSection 300~Installation 2.Attach the desk stand to the bottom of the phone by aligning the tabs and tab guides and sliding it into place (Figure 3-15). Figure 3-15. Desk stand attachment for DSLT wail mounting I . 3.Remove the handset guide with a small screwdriver, turn it over, and reinsert it into the phone, Figure 3-16. Handset guide insertian for waU-n i Handset Guide unting, DSLT 3-16DBS Manual - Issued 6/l/95DBS-70-300
Section 300~InstallationChapter 3. Cabinet Installation System Initialization 1.Confirm that the DBS power switch is OFF. 2.Plug the power cord into a dedicated 120V 15 amp AC wall outlet. Note: A surge protector should be installed on the power cord. 3.Set SW1 on the CPC card to RAMCLR (RAM Clear). ‘igure 3-17. CPC memory clear switch 4.Turn the power switch on. As the system loads, the bottom LED lamp on the CPC card will flash. . 5.Once the bottom LED lamp on the CPC card stops flashing, set SW 1 on the CPC to RAMHOLD.DES-70-300DBS Manual - Issued 8/l/953-l 7