Home > Panasonic > Communications System > Panasonic Cpc+AII/B Digital Business System Release Notes Manual

Panasonic Cpc+AII/B Digital Business System Release Notes Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Panasonic Cpc+AII/B Digital Business System Release Notes Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 10737 Panasonic manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    Page
    of 1046
    							Section 300~InstallationChapter 4. Trunks and Lines
    Table 4-l 7. Tl and analog trunk assignments, DBS 96 + DBS 96 (24-channel Tl in the master; 24-
    channel Tl in the slave)
    Trunk NumberMaster CabinetSlave Cabinet
    :Analog trunk 1
    .LN/A
    8Analog trunk 8
    :Tl channel 24
    LN/A
    16Tl channel 17
    17Tl channel 16
    11N/A
    24
    Tl channel 9
    25Tl channel 8
    .LJ-N/A
    32
    Tl channel 1
    33Analog trunk 1
    1N/A.L
    40Analog trunk 8
    41Tl channel 24
    1N/AJ..
    48Tl channel 17
    49Tl channel 16
    -JN/A1
    56Tl channel 9
    57Tl channel 8
    4.NIA.L
    64Tl channel 1DBS-70-300
    DBS Manual - Issued 8/1’/954-19 
    						
    							Chapter 4. Trunks and Lines
    Section 300~Installation
    Installation
    The following procedures provide step-by-step instructions for installing the
    Tl Interface. The procedure that you should use depends on the type of
    system you have and the number of Tls you are installing.
    If you are installing . . .1 Use this procedure...1
    A Tl in a single cabinet“Installing a Tl in a Single Cabi-
    net” (page 4-21)
    One 
    Tl in a double cabinet, with the“Installing a Tl in a Single Cabi-
    Tl’ located in the masternet” (page 4-21)
    One 
    Tl in a double cabinets, with the
    “Installing a Tl in a Double Cabi-
    Tl located in the slave
    net with the Tl in the Slave”
    (page 4-27)
    Tls in both the master and slave
    “Installing a 
    Tl in a Double Cabi-
    net with Tls in the Master and
    Slave” (page 4-27)4-20
    DES Manual - issued 8/l/95DBS-70-300 
    						
    							Section 300~installation
    Installing a Tl in a Single Cabinet
    Chapter 4. Trunks and Lines
    The following instructions explain how to install a Tl in a single-cabinet
    system. These instructions also apply when a 
    Tl is installed in only the
    master cabinet of a two cabinet system.
    If only one 
    Tl is installed in a two-cabinet system, it must be installed in the
    cabinet specified in Table 4-8 on page 4- 13.
    Note: The Tl Interface cannot be used for systems consisting of a DBS 72
    connected to a DBS 40.
    1.Check connector 4 (CN4) on the Sync Unit (VB-43563). Make sure that
    Pins 2 and 3 are strapped. (See Figure 4-5.)
    When Pins 2 and 3 are strapped, the Sync Unit synchronizes the DBS 
    Tl
    card with the signaling provided by the public network.Figure
    4-S.ConnectorfCN4)straimina,Sync
    0
    CN3.*.......a..... . . . . ...*.....
    CNlCN4
    Jr?0,
    DBS-70-300DBS Manual - Issued 8/l/954-21 
    						
    							Chapter 4. Trunks and LinesSection 300-installation
    2.Attach the Sync Unit to the CPC-B card.
    Note: Before attaching the Sync Unit. insert the three spacers provided
    with the unit and remove the jumpers from 
    CN2 of the CPC-B card.
    Fivure 1-6.Tl Svnc C’nit instdhtinn
    BPU Chip
    (Version 1.3
    or higher)
    CPC-B Card
    4-22
    DBS Manual - Issued 8/l/95DBS-70-300 
    						
    							Section 300-Installation
    Chapter 4. Trunks and Lines
    Fil
    3.Lnstall the Tl MDF (main distribution frame) card in the top of the
    cabinet as shown in Figure 4-7.
    re 4-7. Tl MDF card installation
    GroundScrew
    DBS-70-300
    DBS Manual - issued 8/1I954-23 
    						
    							briaprer 4. I run6 am LIII~S
    4.Set SW1 on the Tl card according to the following table.
    These switch settings correspond to the distance between the DBS and the
    CSU. To turn a switch on, fiip it to the “up” position.
    Table 4-18. Switch settings for SWZ on the Tl card
    Fil
    SWDistance from the DBS to the CSU
    0to150ft.1150-450ft,1450-655ft.
    SW1
    OnOffOff
    SW2OffOnOff
    SW3offOffOn
    SW4OffOnOff
    SW5OffOffOn
    SW6
    OffOnOff
    I offI on
    1 Not used1 Not used
    I
    1 Not used
    a 5.install the Tl card in the “EQTRK” slot
    6.Connect the Sync Cable from CNl on the Sync Unit to CN5 on the Tl
    card.
    pre4-8. Svnc Unit and Tlconnection.sin&-cabinet installation
    7.Connect the cable attached to CN3 on the Tl MDF card to CN3 on the Tl
    card (Figure 4-10).
    8.Using an RJ48 cable, connect CNl on the Tl MDF card to the CSU
    (Figure 
    4- 10). The following illustration shows CNl pinouts.
    4-24DE3 Manual - Issued 8/l/95DBS-70-300 
    						
    							Section 300~InstallationChapter 4. Trunks and Lines
    Figure 4-9. RJ4
    18 pinouts. CNI connectorc2
    10000
    TiPlRingNC8FG0000
    17RingNCTPFGII
    RecelvmIICN 1 
    (RJ48)DBS-70-300DBS Manual 
    - Issued 8/l/954-25 
    						
    							mapter 4. t rums ano Lmessectlon mmstattatton
    9.Connect the ground cable from the Tl MDF card to the cabinet as shown
    in Figure 4- 10.
    gure 4-10. Tl cabinet connections, single-cabinet instalkztion
    n\ T-1 Line (
    t Ground Cable
    Sync Unit
    4-26DBS Manual - Issued 8/l/95DBS-70-300 
    						
    							Section 300~installationChapter 4. Trunks and Lines
    Installing Tl in a Double Cabinet with the Tl in the Slave
    1.
    2.
    3.
    4.
    5.
    6.
    7.
    8.
    Install the Sync Unit in the master cabinet as described in Steps 1 and 2
    under “Installation for a Single 
    Tl.”
    Install a Tl MDF card in the slave cabinet. (See Step 3 on page 4-23.)
    Set Switch 1 on the 
    Tl card. (See Step 4 on page 4-24.)
    Install a 
    Tl card in the “EQTRK” slot of the slave cabinet.
    Connect the Sync Cable from 
    CNl on the Sync Unit to CN5 on the Tl
    card (Figure 4-l 1).
    Note: Part Number VB-43564 is used for the Sync Cable when a Tl is
    installed only in the slave cabinet of 
    a’ two-cabinet system.
    At the slave cabinet, connect the cable attached to CN3 on the 
    Tl MDF
    card to CN3 on the 
    Tl card (Figure 4-10).
    Using an RJ48 cable, connect 
    CNl of the Tl MDF card to the CSU. (See
    Figure 4-9 on page 4-25 for RJ48 pinouts.)
    At the slave cabinet, connect the ground cable on the 
    Tl MDF card as
    shown in Figure 4-10 on page 4-26.
    DES-70-300
    DBS Manual - Issued 8/l/954-27 
    						
    							Lhapter 4. I runis ana LmesSection 3004nstallationCard
    Label
    \connections,
    double-cabinetwith a TI in the slaveCard
    Labe\
    ,,,,,&i;it Eel
    ,, Connector
    Sync. Unit\ CNl n)
    4-20DBS Manual - Issued 8/l/95DBS-70-300 
    						
    All Panasonic manuals Comments (0)

    Related Manuals for Panasonic Cpc+AII/B Digital Business System Release Notes Manual