Home
>
Panasonic
>
Communications System
>
Panasonic Cpc+AII/B Digital Business System Release Notes Manual
Panasonic Cpc+AII/B Digital Business System Release Notes Manual
Have a look at the manual Panasonic Cpc+AII/B Digital Business System Release Notes Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 10737 Panasonic manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
![Page 488
Page 2-2
DBS Manual - Issued 8/l/95*DE!%70-400
‘\](http://img.usermanuals.tech/thumb/58/85067/w64_panasonic-dbs-40-72-96-rel-notes-ver-8_d-487.png "Page 488
Page 2-2
DBS Manual - Issued 8/l/95*DE!%70-400
‘\")
3ecuon 4uu-rrogrammingc;naprer 2. i runK rrogramming (i-qPooled Trunk Access for Group “9” Software Version: All VersionsAddress: FF2 (Trunk)# 3# (0 or l)# DescriptionUse this feature to place a trunk in a group from which trunks are automatically chosen for outbound dialing. When you dial “9” from an SLT or digital extension, or press an FF key that is set as a pooled trunk key, any available trunk in the group will be accessed. The trunk selection is made from the highest trunk number in the group to the lowest. ProgrammingtFF2 (l-64)# 3# (0 or I)# ft Trunk Num bkrO=Trunk is not included in access group “9”. l=Trunk is included in access group “9”. Related ProgrammingLCR Access: FFl 2# l# 3# (0 or l)# NotesInteraction with LCR.Set the “LCR Access” option (address FF12# l# 3#) so that dialing “9” indicates a Pooled Trunk call.If this option is set so that dialing “9” indicates an LCR call, trunk selection will default to pooled trunk line access group 9 if all lines that could be used for LCR access are busy. Required Hardware Setting. To use pooled trunks, Strap S 1 on the CPC card must be cut.See Section 300~Installation for instructions. DBS-70-400DBS Manual - issued 8/l/95Page 2-5
Chapter 2. Trunk Programming (FF2)Section 400-Programming Pooled Trunk Access for Groups 1L81-86”Software Version: All Versions Address: FF2 (Trunk)# (419)# (0 or I)# DescriptionUse this feature to place a trunk in a group from which trunks are automatically chosen for outbound dialing. When you dial 81,82,83,84,85, or 86 from an SLT or digital extension, or press an FF key that is set as a pooled trunk key, any available trunk in the group will be accessed. The trunk selection in a particular group is made from the highest available trunk number to the lowest available trunk number. Programming Notes y-64)#(i,, (0 orf# Trunk NumberPooled Trunk Group:O=The trunk is not 4==Group81included. 5=Group 82l=The trunk is included. 6=Group83 7=Group84 8=Group85 9=Group86 Placing Trunks In More Than One Group.The same trunks may appear in more than one pooled trunk group, including trunk group 9. Required Hardware Setting.To use pooled trunks, Strap S 1 on the CPC card must be cut. See Section 300~Installation for instructions. Page 2-6DES Manual - Issued 8/l/95DBS-70-400
Section 400-ProgrammingChapter 2. Trunk Programming (FF2)Trunk Port Type Software Version: -All VersionsAddress: FF2 (Trunk)# lO# (1 or 2)# DescriptionEach trunk port must be identified as a regular CO trunk or as a PBX line. Programming .FF2 (I-64)# lO# (1 or 2)# t t Trunk Numberl=Regular (CO) trunk 2=PBX line Related ProgrammingAuto Flash R&al: FFl 2# l# 6# (0 or l)#PBX Access Codes: FFl 2# 3# (l-8)# (O-999 or 0* to 99*)# Automatic Pause Position for PBX Access Codes: FFl 2# 3# (9-18)# (l-3)#Automatic Pause Timer: FFl 3# 12# (0- 15)#PBX Flash Timer: FFl 3# 18# (O-10)+! Trunk Port Type: FF2 (l-64)# lO# ( 1 or 2)# Automatic Pause For PBX Line: FF2 (l-64)# 13# (0 or l)# NotesToll Restriction Interaction. TRS settings (FM addresses) can be affected by this parameter. DBS-70-400DBS Manual - Issued 8/l/95Page 2-7
Chapter 2. Trunk Programming (FF2j Section 400-Programming DISA Auto Answer Software Version: All VersionsAddress: FF2 (Trunk)# ll# (0 or l)# DescriptionUse this feature to set a trunk(s) to automatically provide DISA tone upon connection with an inbound caller.(However, after hearing the DISA tone, the caller will still have to enter an ID code in order to use DISA.) If a trunk is set to provide DISA tone, you can limit DISA operation on that trunk to a certain number of hours each day, using the DISA Start Time and DISA End Time addresses. ProgrammingFF2 (l-64)# 11# (0 or l)# tt Trunk NumberO=DI!SA tone is not provided. l=DISA tone is urovided. Related ProgrammingCaller ID Automatic DISA: FFl 2# 8# (l-lO)# (PhoneNo.)# Direct Inward System Access (DISA) ID Code: FFl 5# (0000-9999)#DISA Outbound Call ID Code 1: FFl 6# l# (0000-9999)#DISA Outbound Call ID Code 2: FFl 6# 2# (0000-9999)#DISA Start Time: FF2 (Trunk)# 19# (HHMM)##DISA End Tie: FF2 (Trunk)# 20# (HHMM)# NotesCaller ID Znferaction.If your DBS system supports Caller ID, do not enable DISA on any trunk using this address. (Caller ID will automatically enable or disable DISA to the caller based on the phone number he is calling from.) DZSA Hardware Requirement.An MFR card is required for DISA, so that the system can interpret DTMF tones entered via the DISA connection. Page 2-8DBS Manual - Issued 8/l/95DBS-70-400
Section 400-ProgrammingChapter 2. Trunk Programming (FF2)Private Trunk Line Software Version: All VersionsAddress: FF2 (Trunk)# 12# (ExtPort)# DescriptionUse this address to assign a private trunk line to an extension. A number of private trunks can belong to one extension. Once a private trunk is assigned to an extension, other extensions cannot make outbound calls or receive inbound calls on that trunk (the system wili assign Toll Restriction Type 0 to the trunk on all other extensions). The system will assign TRS Type 7 (no restrictions) to the private trunk assigned to the extension. Programming To assign a Private Trunk Line(s) to an exterision . . .FF2 (l-64)# 12# (11144)# t Trunk Number f Extension Port Number To cancel Private Trunk assignment(s) for an extension . . . IFF2 (l-64)# 12# (19144)# CONF ON/OFFI Related Programming Day TRS Types O-7 for Trunks:FF7 7# (ExtPort)## (Trunk)# (0-7)# Night TRS Types O-7 for Trunks:FM 8# (ExtPort)# (Trunk)++ (0-7)# NotesReprogramming Toll Restrictions for Disabled Private Trunks.If a private trunk setting is enabled and then later disabled, the system will not automatically make that trunk available to other extensions. (TRS Type 0 will apply to that trunk on all extensions.) Therefore, the trunk’s TRS type must be manually reprogrammed for each extension wishing to use that trunk (using addresses FF7 7# and FF7 8#). DBS-70-400DBS Manual - Issued 8/l/95Page 2-9
bnaprer 2. I ruiln rrogrammlng (rrq3ecwtl 4uu-rrogrammlng Automatic Pause for PBX Line Software Version: All VersionsAddress: FF2 (Trunk)# 13# (0 or l)# DescriptionThis address determines if a pause is automatically inserted during the dialing of a PBX access code. If this address is enabled, the system will automatically pause after dialing the first, second, or third digit of the PBX access code. See the PBX Access Code(s) address (FFl 2# 3# 9-18# l-3#) for more information. If this address is disabled (default setting), the phone, user must manually insert a pause by pressing REDIAL. The length of the pause (whether inserted manually by the user or automatically by the system) is determined by the Automatic Pause Timer, which isset at address FFl 3# 12#. Note:Before assigning the automatic pause, you must first designate the trunk as a “PBX line” (FF2 Trunk# lO# 2#). ProgrammingFF2 (l-64)# 13# (0 or l)# Trunk NumberO=Automatic pause is enabled. l=Automatic pause is disabled. Related Programming Automatic Pause Position for PBX Access Codes: FFl 2# 3# (9-18)# (l-3)#PBX Flash Timer: FFl 3# 18# (0-lO)##Trunk Port Type: FF2 (Trunk)# lO# (1 or 2)# Page 2-10DBS Manual - Issued 8/l/95DBS-70-400
Dial Tone Detection Software Version: All VersionsAddress: FF2 (Trunk)# 14# (0 or l)# DescriptionThis program determines when dialed digits are outpulsed -- either according to the Dial Pause Timer setting (FFl 3# 17#), or after the DBS detects dial tone. Programming FF2(I-64)#14#I (0 or l)# Trunk NumberO=Digits are outpulsed according to the Dial Pause Timer. l=Digits are outpulsed after dial tone is detected. .Related Programming Dial PauseTimer: FFl 3# 17# (0-15)#DBS-70-400DBS Manual - Issued 8/l/95Page 2-11
Outbound DTMF Signal Duration for Auto-Dialed Digits Software Version: All VersionsAddress: FF2 (Trunk)# 15# (1.3)# DescriptionThis address controls DTMF signal duration when digits are dialed automatically by the system rather than the user. Examples of DBS dialing include:l Redial l Saved Number Redial l Speed Dialing l Adding LCR digits Programming IFF2 (I-64)# 15# (113)# tt Trunk Number1=75 ms on/50 m off 24125 ms on/125 ms off 3=250 ms on/250 ms off NotesDTMF Tone for Manual Dialing.If you dial manually (press a digit key), the DTMF tone will emit until the button is released.Page 2-l 2DBS Manual - issued 8/l/95DES-70-400
Section 400-Programming Chapter 2. Trunk Programming (FF2) Unsupervised Trunk Conference Software Version: All VersionsAddress: FF2 (Trunk)# 16# (0 or l)# DescriptionUse this feature to enable trunk(s) to be used in an unsupervised conference call. Pro,grammingFF2 (l-64)# 16# (0 or l)# ft Trunk NumberO=The CO’trunk cannot be used for an unsupervised conference. l=The CO trunk can be used for an unsupervised conference. Notes automatically disconnected according to the Unsupervised Conference Timer setting (FF13# ll# O-l.%). Related Programming Unsupervised Conference Timer: FFl 3# 1 l# (0-15)# Unsupervised Conference:FF3 (ExtPortj# 13# (0 or l)# Unsupervised Conference Timer Operation.A conference call will be DES-70-400DBS Manual - Issued 8/l/95Page 2-13
bIlaprttr L. I runK rrograrrwaiiy t-2)3w.xu11 4uu-rroyrairirriirig Inbound Ring Pattern Software Version: All VersionsAddress: FF2 (Trunk)# 17# (0-9)# DescriptionEach CO trunk can be assigned a distinctive ring pattern for easy recognition of the trunk during an incoming call. Up to 9 different ring patterns are available. Programming rFF2 (1164)# 17# f Trunk Number Inbound Ring Pattern Default: 0 (determined by CO) (see the following table) Table 2-1.Ring P&ems for inbound trunk calls Notes SettingValue 0Synchronize (ring pattern determined by CO) I13 sec. on’1 sec. off 121 2 sec. on/2 sec. off 3 4 1 sec. on/l sec. off 1 sec. on/2 sec. off I 51 sec. on/3 sec. off 6.5 sec. on/S sec. offIII 7 1 .5 sec. on/.5 sec. off/.5 sec. on/%.5 sec. off. 1 .5 sec. on/3.5 sec. offI 1 1 sec. on/7 sec. off Transferred Calls.This setting does not affect transferred calls. The ring pattern for transferred calls can be set in the Transfer Ring Pattern address (FFl 2# l# 31# 0-6#). Precedence of Extension Ring Pattern Setting.The ring pattern (if any) assigned to the extension (FF3 ExtPor# 39# Pattem#) will override this Inbound Ring Pattern for incoming trunk calls. Page 2-l 4DBS Manual - Issued 8/l/95DBS-70-400