Sharp Mx 4100n Owners Manual

							4
INSTALLATION REQUIREMENTS
Improper installation may damage this product. Please note the following during initial installation and whenever the 
machine is moved.
1. The machine should be installed near an accessible 
power outlet for easy connection.
2. Be sure to connect the power cord only to a power 
outlet that meets the specified voltage and current 
requirements. Also make certain the outlet is properly 
grounded.
 For the power supply requirements, see the name 
plate in the lower left corner of the left side of the 
machine.
Connect the machine to a power outlet which is not 
used for other electric appliances. If a lighting fixture is
connected to the same outlet, the light may flicker.
3. Do not install the machine in areas that are:
 damp, humid, or very dusty 
 exposed to direct sunlight 
 poorly ventilated 
 subject to extreme temperature or humidity 
changes, e.g., near an air conditioner or heater.
4. Be sure to allow the required space around the 
machine for servicing and proper ventilation.
5. The machine includes a built-in hard drive. Do not 
subject the machine to shock or vibration. In 
particular, never move the machine while the power is 
on.
17-23/32
(45cm) 11-13/16
(30cm)11-13/16
(30cm)
A small amount of ozone is produced within the printer during operation. The emission level is insufficient to cause any health 
hazard.
NOTE:
The present recommended long term exposure limit for ozone is 0.1 ppm (0.2 mg/m
3) calculated as an 8 hr. time-weighted average 
concentration.
However, since the small amount that is emitted may have an objectionable odor, it is advisable to place the copier in a ventilated 
area.
mx5001_us_saf.fm  4 ページ  ２００８年９月２４日　水曜日　午前９時４５分 
						

							5
SUPPLIES
Standard supplies for this product that can replaced by the user include paper, toner cartridges, and staple cartridges for 
the finisher.
Be sure to use only SHARP-specified products for the toner cartridges, finisher staple cartridge, saddle stitch finisher 
staple cartridge, and transparency film.
Storage of supplies
Proper storage
1. Store the supplies in a location that is:
 clean and dry,
 at a stable temperature,
 not exposed to direct sunlight.
2. Store paper in the wrapper and lying flat.
3. Paper stored in packages standing up or out of the wrapper may curl or become damp, resulting in paper misfeeds.
Storing toner cartridges
Store a new toner cartridge box horizontally. Do not store it standing on end. If stored standing on end, the toner may not 
distribute well even after shaking the cartridge vigorously, and will remain inside the cartridge without flowing out.
Staple cartridge
The finisher and saddle stitch finisher require the following staple cartridge:
MX-SCX1 (for finisher and saddle stitch finisher)
Approx. 5000 per cartridge x 3 cartridges
AR-SC2 (for finisher (large stacker))
Approx. 5000 per cartridge x 3 cartridges
AR-SC3 (for saddle stitch finisher only)
Approx. 2000 per cartridge x 3 cartridges
Supply of spare parts and consumables 
The supply of spare parts for repair of the machine is guaranteed for at least 7 years following the termination of 
production. Spare parts are those parts of the machine which may break down within the scope of the ordinary use of 
the product, whereas those parts which normally exceed the life of the product are not to be considered as spare parts. 
Consumables too, are available for 7 years following the termination of production.For best copying results, be sure to use only Sharp Genuine Supplies which are designed, 
engineered, and tested to maximize the life and performance of Sharp products. Look for the 
Genuine Supplies label on the toner package.
GENUINE SUPPLIES
mx5001_us_saf.fm  5 ページ  ２００８年９月２４日　水曜日　午前９時４５分 
						

							
6
SPECIFICATIONS
Machine specifications / copier specifications
* First copy out time is measured with original on the document glass in full ready condition with fuser at operating temperature and 
mirror motor at operating speed in each of black and white mode  and color mode, actual time may vary based on environment 
conditions.
NameDigital Full Color Multifunctional System MX-4100N/MX-4101N/MX-5001N
TypeDesktop
Photoconductive typeOPC drum
Printing methodElectrophotographic system (laser)
Developer systemDry-type two-component m agnetic brush development
Fusing systemHeat rollers
Scanning resolution
Document glass
Black and white scanning: 600 x 300 dpi (factory default values), 
600 x 400 dpi, 600 x 600 dpi
Color scanning: 600 x 600 dpi (factory default values)
Reversing single pass 
feeder (automatic 
document feeder)
Black and white scanning: 600 x 400 dpi (factory default values), 600 x 600 dpi
Color scanning: 600 x 600 dpi (factory default values)
Printing resolution600 x 600 dpi
Scanning gradation256 levels
Printing gradationEquivalent to 256 levels
Original sizes / typesMax. 11 x 17 (A3) / sheets, bound documents
Copy sizesMaximum: 12 x 18 (A3W) Mini mum: 5-1/4 x 5-3/4 (A5R)
Print marginsLeading edge / trailing edge: total 21/64 (8 mm) or less, 
near edge / far edge: total 11/64 ±3/32 (4 mm ±2 mm) or less
Warm-up time
MX-4100N/MX-4101N: 120 seconds or less
MX-5001N: 140 seconds or less
(at room temperature of 73.4°F (23°C) and rated voltage)
First-copy time*
MX-4100N/MX-4101N Color copy time: 6.7 seconds or less
Black and white copy time: 4.7 seconds or less
MX-5001N Color copy time: 5.9 seconds or less Black and white copy time: 4.1 seconds or less
(Portrait feeding of 8-1/2 x 11 (A 4) sheets from 1st paper tray, without auto color selection and auto 
color mode. Excluding the first page out put after the power is turned on.)
Copy ratios
Variable: 25% to 400% in increments of 1%, total 376 increments (25% to 200% when the automatic 
document feeder is used)
Fixed presets: 25%, 50%, 64%, 77%, 100%, 121%, 129%, 200% and 400% for inch sizes;
25%, 50%, 70%, 81%, 86%, 100%, 115%, 122%, 141%, 200% and 400% for AB sizes.
Two reduction ratios and two enlargement ratios can be stored.
Continuous copy999 copies
Automatic document 
feederSee Automatic document  feeder specifications.
Tray 1 / Tray 2
Paper sizes: 11 x 17, 8-1/2 x 14, 8-1/2 x 13-1/ 2, 8-1/2 x 13-2/5, 8-1/2 x 13, 8-1/2 x 11, 
8-1/2 x 11R, 7-1/4 x 10-1/2 R, 5-1/2 x 8-1/2R, A3, B4, A4, A4R, B5, B5R, A5R, 
8K, 16K, 16KR
Paper weight: Plain paper (16 lbs. to 28 lbs. (60 g/m
2 to 105 g/m2)), heavy paper (28 lbs. bond to 
110 lbs. index (106 g/m2 to 209 g/m2))
Paper capacity: Plain paper (21 lbs. (80 g/m2)) 500 sheets,  heavy paper 200 sheets
Paper types: SHARP-recommended plain paper, recycled paper, colored paper, and heavy paper
mx5001_us_saf.fm  6 ページ  ２００８年９月２４日　水曜日　午後１時０分 
						

							
7
SPECIFICATIONS
Machine specifications / copier specifications (Continued)
*1 Output tray (Center tray) cannot  be used when the finisher or saddle stitch finisher is installed.
*2 Type A connectors are located on the fr ont of the machine and on the right side of the machine at the back (total of two 
connectors); however, the connectors  cannot be used simultaneously. Only one of the connectors can be used.
Bypass tray
Paper sizes: 12 x 18, 11 x 17, 8-1/2 x 14, 8- 1/2 x 13-1/2, 8-1/2 x 13-2/5, 8-1/2 x 13, 
8-1/2 x 11, 8-1/2 x 11R, 7- 1/4 x 10-1/2R, 5-1/2 x 8-1/2R, envelopes, A3W, A3, 
B4, A4, A4R, B5, B5R, A5R, 8K, 16K, 16KR  (Includes automatic paper size detection 
function. Entry of paper sizes up to 11-5/8 x 17 (297 mm x 432 mm) is possible.)
Paper weights:
Thin paper (15 lbs. to 16 lbs. (55 g/m
2 to 59 g/m2)), plain paper (16 lbs. to 28 lbs. (60 g/m2 to 
105 g/m2)), heavy paper (28 lbs. bond to 140 lbs. index (106 g/m2 to 256 g/m2)),
envelopes (20 lbs. to 24 lbs. (75 g/m2 to 90 g/m2))
Paper capacity: Standard paper 100 sheets
Paper types:
SHARP-recommended plain paper, recycled paper, colored paper, heavy paper, thin paper, 
transparency film, envelopes (Monarch, Com-10, DL, C5)
Duplex module
Paper sizes: 11 x 17, 8-1/2 x 14, 8-1/2 x 13, 8-1/ 2 x 11, 8-1/2 x 11R, 5-1/2 x 8-1/2R, A3, B4, 
A4, A4R, B5, B5R, A5R, 8K, 16K, 16KR
Paper weight: Plain paper (16 lbs. to 28 lbs. (60 g/m2 to 105 g/m2)), heavy paper (28 lbs. bond to 
110 lbs. index (106 g/m2 to 209 g/m2))
Paper types: SHARP-recommended plain paper, recycled paper, colored paper, and heavy paper
Output tray (Center tray)*1
Output method: Face-down output (12 x 18 and A3W  paper can be output to right tray, finisher, or 
saddle stitch finisher)
Output capacity: 500 sheets (using SHARP-recommended 8-1/2 x 11 or A4 paper)
(The maximum number of sheets that can be hel d varies depending on ambient conditions in the 
installation location, the type of paper,  and the storage conditions of the paper.)
Tray full sensor: Yes
Interface port
LAN connectivity: 10Base-T / 100Base-TX / 1000Base-T
USB connectivity:
Type A connector supports USB 2.0 (Hi speed)*2
Compatibility requirements of USB memory
Memory capacity : Max. 32 GB
Disk Format : FAT32 only
Type B connector supports USB 2.0 (Hi speed)
Required power supplyAC 120 V ±10% 60 Hz
Power consumptionMX-4100N/MX4101N: 1.44kW
MX-5001N: 1.92kW
Typical electricity 
consumptionMX-4100N: 12.95 kWh/week
MX-4101N: 13.68 kWh/week
MX-5001N: 13.89 kWh/week
Dimensions
MX-4100N:
25-25/64 (W) x 27-3/8 (D) x 37-25/64 (H) (645 mm (W) x 695 mm (D) x 950 mm (H))
MX-4101N/5001N:
25-25/64 (W) x 27-3/8 (D) x 37-51/64 (H) (645 mm (W) x 695 mm (D) x 960 mm (H))
WeightMX-4100N: Approx. 262.4 lbs. (119 k g)
MX-4101N/5001N: Approx. 282.2 lbs. (128 k g)
Overall dimensions39-11/64 (W) x 27-3/8 (D) (995 mm (W) x  695 mm (D)) (when bypass tray is extended)
mx5001_us_saf.fm  7 ページ  ２００８年９月２４日　水曜日　午後３時５８分 
						

							8
SPECIFICATIONS
Continuous copying speeds*
* Copy speed during output of the second copy and following copies when performing continuous one-sided copying of the same 
page (excluding offset output) using plain one-sided paper from a tray other than the bypass tray.
ModelMX-4100N/MX-4101N MX-5001N
Copy ratio100% / Reduced / Enlarged
Copy modeColor  copying Black and white copying Color  copying Black and white copying
11 x 17, A3, 8K19 copies/min. 19 copies/min. 22 copies/min. 22 copies/min.
8-1/2 x 14,  8-1/2 x 13, 
B422 copies/min. 22 copies/min. 25 copies/min. 25 copies/min.
8-1/2 x 11, A4, B5, 16K41 copies/min. 41 copies/min. 50 copies/min. 50 copies/min.
8-1/2 x 11R, 
7-1/4 x 10-1/2R, A4R, 
B5R, 16KR
26 copies/min. 26 copies/min. 30 copies/min. 30 copies/min.
5-1/2 x 8-1/2R, A5R29 copies/min. 29 copies/min. 32 copies/min. 32 copies/min.
Ambient environment
85% (Humidity)
(Temperature) 60%
20%
54F
(10C)86F
(30C)91F
(35C)
mx5001_us_saf.fm  8 ページ  ２００８年９月２４日　水曜日　午前９時４５分 
						

							9
SPECIFICATIONS
Acoustic noise emission (measurement according to ISO7779)
Emission concentration 
(measurement according to RAL-UZ122: Edition Jun. 2006)
Automatic document feeder specifications
*1 Scanning in mono 2 mode of one side only is possible in fax and scan send modes. However, when the resolution is 600 x 600 dpi 
in Internet fax mode, the maximum length is 31-31/64 (800 mm). When the resolution is 400 x 400 dpi or 600 x 600 dpi in scan 
mode, a long original cannot be scanned.
*2 Paper weights from 9 lbs. (35g/m
2) to 13 lbs. (49g/m2) require the use of slow scan mode. MX-4100N/MX-4101N MX-5001N
Sound power level L
wA
Printing mode (continuous printing)Color: 6.8B Black and white: 6.9BColor: 7.0B Black and white: 7.0B
Standby mode5.1 B 5.3 B
Sound pressure level L
pA (actual measurement)
Printing mode
Bystander positionsColor: 53 dB (A)
Black and white: 53 dB (A)Color: 54 dB (A)
Black and white: 53 dB (A)
Operator positionsColor: 53 dB (A)
Black and white: 52 dB (A)Color: 52 dB (A)
Black and white: 52 dB (A)
Standby modeBystander positions36 dB (A) 38 dB (A)
Operator positions35 dB (A) 37 dB (A)
Measured substanceMachine stateColor modeDiffusion speed
Ozone
During copying operationBlack & white 1.5 m
g/h or less
Color 3.0 m
g/h or less
DustBlack & white 4.0 mg/h or less
Color 4.0 m
g/h or less
StyreneBlack & white 1.0 mg/h or less
Color 1.8 m
g/h or less
BenzeneBlack & white Less than 0.05 mg/h
Color Less than 0.05 m
g/h
TVOC
Black & white 10 mg/h or less
Color 18 m
g/h or less
Standby2.0 mg/h or less
ModelMX-4100N MX-4101N/MX-5001N
Original sizes
11 x 17 to 5-1/2 x 8-1/2, A3 to A5, long paper 
(max. width 11-5/8 (297 mm) x max. length 39-23/64*1 (1000 mm), scanning in mono 2 mode of 
one side only is possible in fax and image scan modes)
Original weight
One-sided 9 lbs. to 32 lbs*2. (35g/m2  to 
128
g/m2)
Two-sided 13 lbs. to 28 lbs. (50
g/m2 to 105g/m2)One-sided 9 lbs. to 32 lbs. (35
g/m2  to 128g/m2)
Two-sided 13 lbs. to 32 lbs. (50
g/m2 to 128g/m2)
Capacity100 sheets (21 lbs. (80g/m2)) Maximum stack 
height of 33/64 (13 mm)150 sheets (21 lbs. (80g/m2)) Maximum stack 
height of 33/64 (13 mm)
mx5001_us_saf.fm  9 ページ  ２００８年９月２４日　水曜日　午前９時４５分 
						

							10
SPECIFICATIONS
Exit tray unit (right tray) specifications
* The maximum number of sheets that can be held varies depending on ambient conditions in the installation location, the type of 
paper, and the storage conditions of the paper. Envelopes, tab paper, and glossy paper cannot be output.
Stand/1x500 sheet paper drawer specifications
ModelMX-TRX2
Output methodFace-down output
Output capacity100 sheets (using SHARP-recommended 8-1/2 x 11 or A4 paper)
Dimensions
When tray is folded up:
11-3/8 (W) x 15-61/64 (D) x 2-3/64 (H) (289 mm (W) x 405 mm (D) x 52 mm (H))
When tray is extended:
16-1/2 (W) x 15-61/64 (D) x 2-3/64 (H) (419 mm (W) x 405 mm (D) x 52 mm (H))
WeightApprox. 2 lbs. (0.93 kg)
ModelMX-DEX8
Paper sizes11 x 17, 8-1/2 x 14, 8-1/2 x 13-1/2, 8-1/2 x 13-2/5, 8-1/2 x 13, 8-1/2 x 11, 8-1/2 x 11R, 
7-1/4 x 10-1/2R, A3, B4, A4, A4R, B5, B5R, 8K, 16K, 16KR
Paper weightPlain paper (16 lbs. to 28 lbs. (60g/m2 to 105g/m2)), heavy paper (28lbs. bond to 110 lbs. index 
(106
g/m2 to 209g/m2))
Paper capacity500 sheets (21 lbs. (80g/m2)) x 1 tray
Paper typesSHARP-recommended plain paper, recycled paper, and colored paper
Automatic paper size 
detection
When Auto-Inch detection is selected:
11 x 17, 8-1/2 x 14, 8-1/2 x 11, 8-1/2 x 11R, 7-1/4 x 10-1/2R
When Auto-AB detection is selected:
A3, B4, A4, A4R, B5, B5R, 216 mm x 330 mm (8-1/2 x 13)
Power supplySupplied from the machine
Dimensions28-11/32 (W) x 26-3/8 (D) x 11-15/16 (H) (720 mm (W) x 670 mm (D) x 303 mm (H))
(including adjuster)
WeightApprox. 44.1 lbs. (20 kg)
mx5001_us_saf.fm  10 ページ  ２００８年９月２４日　水曜日　午前９時４５分 
						

							11
SPECIFICATIONS
Stand/2x500 sheet paper drawer specifications
Large capacity tray specifications*
* A stand/1x500 sheet paper drawer or stand/2x500 sheet paper drawer is required to connect the large capacity tray to the machine.
ModelMX-DEX9
Paper sizes11 x 17, 8-1/2 x 14, 8-1/2 x 13-1/2, 8-1/2 x 13-2/5, 8-1/2 x 13, 8-1/2 x 11, 8-1/2 x 11R, 
7-1/4 x 10-1/2R, A3, B4, A4, A4R, B5, B5R, 8K, 16K, 16KR
Paper weightPlain paper (16 lbs. to 28 lbs. (60g/m2 to 105g/m2)), heavy paper (28lbs. bond to 110 lbs. index 
(106
g/m2 to 209g/m2))
Paper capacity500 sheets (21 lbs. (80g/m2)) x 2 tray
Paper typesSHARP-recommended plain paper, recycled paper, and colored paper
Automatic paper size 
detection
When Auto-Inch detection is selected:
11 x 17, 8-1/2 x 14, 8-1/2 x 11, 8-1/2 x 11R, 7-1/4 x 10-1/2R
When Auto-AB detection is selected:
A3, B4, A4, A4R, B5, B5R, 216 mm x 330 mm (8-1/2 x 13)
Power supplySupplied from the machine
Dimensions28-11/32 (W) x 26-3/8 (D) x 11-15/16 (H) (720 mm (W) x 670 mm (D) x 303 mm (H))
(including adjuster)
WeightApprox. 51.9 lbs. (23.5 kg)
ModelMX-LCX1
Paper sizes8-1/2 x 11, A4 (paper size change must be performed by a service technician)
Paper weightPlain paper (16 lbs. to 28 lbs. (60g/m2 to 105g/m2))
Paper capacity3500 sheets (21 lbs. (80g/m2))
Paper typesSHARP-recommended plain paper, recycled paper, and colored paper
Power supplySupplied from the machine
Dimensions14-9/16 (W) x 21-21/32 (D) x 20-15/32 (H) (370 mm (W) x 550 mm (D) x 520 mm (H))
WeightApprox. 63.9 lbs. (29 kg)
mx5001_us_saf.fm  11 ページ  ２００８年９月２４日　水曜日　午前９時４５分 
						

							12
SPECIFICATIONS
Finisher specifications
*1 The maximum number of sheets that can be held varies depending on ambient conditions in the installation location, the type of 
paper, and the storage conditions of the paper.
*2 Up to 10 envelopes can be output.
*3 The height of the sheets must not exceed 2-51/64 (71 mm).
*4 The height of the sheets must not exceed 1-13/32 (35.5 mm).
*5 The maximum number of sheets for stapling assumes a paper weight of 24 lbs. (90g/m
2) and includes two cover sheets of 28 lbs. 
bond to 140 lbs. index (106g/m2 to 256g/m2).
ModelMX-FNX9
Paper sizes
12 x 18, 11 x 17, 8-1/2 x 14, 8-1/2 x 13-1/2, 8-1/2 x 13-2/5, 8-1/2 x 13, 8-1/2 x 11, 
8-1/2 x 11R, 7-1/4 x 10-1/2R, 5-1/2 x 8-1/2R, envelopes, A3W, A3, B4, A4, A4R, B5, B5R, 
A5R, 8K, 16K, 16KR
Paper weight
Thin paper (15 lbs. to 16 lbs. (55g/m2  to 59g/m2))  plain paper (16 lbs. to 28 lbs. (60g/m2 to 105g/m2)) 
heavy paper (28 lbs. bond to 140 lbs. index (106
g/m2 to 256g/m2)) , envelopes (20 lbs. to 24 lbs. 
(75
g/m2 to 90g/m2))
ModesNon-staple, staple
Allowed paper sizes for 
offset11 x 17, 8-1/2 x 14, 8-1/2 x 13-1/2, 8-1/2 x 13-2/5, 8-1/2 x 13, 8-1/2 x 11, 8-1/2 x 11R, 
A3, B4, A4, A4R, B5, 8K, 16K
Offset distance1-3/16 (30 mm)
Tray capacity*1
Non-stapling*2:
500 sheets*3 (8-1/2 x 11, 8-1/2 x 11R, 
7-1/4 x 10-1/2R, 5-1/2 x 8-1/2R, A4, A4R, B5, 
B5R, A5R, 16K, 16KR)
250 sheets*
4 (12 x 18, 11 x 17, 8-1/2 x 14, 
8-1/2 x 13-1/2, 8-1/2x 13-2/5, 8-1/2 x 13, 
A3W, A3, B4, 8K)Stapling*
5:
30 sets or 500 sheets*3 (8-1/2 x 11, 
8-1/2 x 11R, A4, A4R, B5, 16K, 16KR)
30 sets or 250 sheets*
4 (11 x 17, 8-1/2 x 14, 
8-1/2 x 13-1/2, 8-1/2 x 13-2/5, 8-1/2 x 13, 
A3, B4, 8K)
Power supplySupplied from the machine
Dimensions25-3/16 (W) x 23-27/64 (D) x 8-5/64 (H) (640 mm (W) x 595 mm (D) x 205 mm (H)) 
(When tray is extended)
WeightApprox. 28.7 lbs. (13 kg)
Stapler section
Allowed paper sizes for 
stapling
11 x 17, 8-1/2 x 14, 8-1/2 x 13-1/2, 8-1/2 x 13-2/5, 8-1/2 x 13, 8-1/2 x 11, 8-1/2 x 11R, 
A3, B4, A4, A4R, B5, 8K, 16K, 16KR
(Three stapling positions: one staple at bottom left corner, one staple at top left corner, and two 
staples.)
Maximum number of 
sheets for stapling*5
50 sheets (8-1/2 x 11, 8-1/2 x 11R, A4, A4R, B5, 16K, 16KR)
30 sheets (11 x 17, 8-1/2 x 14, 8-1/2 x 13-1/2, 8-1/2 x 13-2/5, 8-1/2 x 13, A3, B4, 8K)
(30 sheets when the sheets are the same width but different lengths.)
Note:
Special media such as transparency film and label sheets cannot be stapled or punched.
mx5001_us_saf.fm  12 ページ  ２００８年９月２４日　水曜日　午前９時４５分 
						

							13
SPECIFICATIONS
Finisher (large stacker) specifications*1
*1 Paper pass unit and stand/1x500 sheet paper drawer or stand/2x500 sheet paper drawer are required to connect the finisher (large 
stacker) to the machine.
*2 The maximum number of sheets that can be held varies depending on ambient conditions in the installation location, the type of 
paper, and the storage conditions of the paper.
*3 Up to 100 sheets of non-standard size paper, envelopes, and transparency film (8-1/2 x 11(A4)) can be loaded.
*4 The maximum number of sheets for stapling assumes a paper weight of 24 lbs. (90g/m
2) and includes two cover sheets of 28 lbs. 
bond to 140 lbs. index (106g/m2 to 256g/m2).
ModelMX-FN11
Paper sizes
12 x 18, 11 x 17, 8-1/2 x 14, 8-1/2 x 13-1/2, 8-1/2 x 13-2/5, 8-1/2 x 13, 8-1/2 x 11, 
8-1/2 x 11R, 7-1/4 x 10-1/2R, 5-1/2 x 8-1/2R, envelopes, A3W, A3, B4, A4, A4R, B5, B5R, 
A5R, 8K, 16K, 16KR
Paper weight
Thin paper (15 lbs. to 16 lbs. (55g/m2  to 59g/m2))  plain paper (16 lbs. to 28 lbs. (60g/m2 to 105g/m2)) 
heavy paper (28 lbs. bond to 140 lbs. index (106
g/m2 to 256g/m2)) , envelopes (20 lbs. to 24 lbs. 
(75
g/m2 to 90g/m2))
ModesNon-staple, staple
Allowed paper sizes for 
offset11 x 17, 8-1/2 x 14, 8-1/2 x 13-1/2, 8-1/2 x 13-2/5, 8-1/2 x 13, 8-1/2 x 11, 8-1/2 x 11R, 
A3, B4, A4, A4R, B5, 8K, 16K
Offset distance1-3/16 (30 mm)
Tray 
capacity*2
Upper tray
Non-stapling*3:
1550 sheets (8-1/2 x 11, 5-1/2 x 8-1/2R, A4, 
B5, A5R, 16K)
650 sheets (12 x 18, 11 x 17, 8-1/2 x 14, 
8-1/2 x 13-1/2, 8-1/2x 13-2/5, 8-1/2 x 13, 
8-1/2 x 11R, 7-1/4 x 10-1/2R, A3W, A3, B4, 
A4R, B5R, 8K, 16KR)Stapling*4:
100 sets or 1550 sheets (8-1/2 x 11, A4, B5, 
16K)
50 sets or 650 sheets (11 x 17, 8-1/2 x 14, 
8-1/2 x 13-1/2, 8-1/2 x 13-2/5, 8-1/2 x 13, 
8-1/2 x 11R, A3, B4, A4R, 8K)
Lower tray
Non-stapling*3:
2450 sheets (8-1/2 x 11, A4, B5, 16K)
1700 sheets (5-1/2 x 8-1/2R, A5R)
650 sheets (12 x 18, 11 x 17, 8-1/2 x 14, 
8-1/2 x 13-1/2, 8-1/2x 13-2/5, 8-1/2 x 13, 
8-1/2 x 11R, 7-1/4 x 10-1/2, A3W, A3, B4, 
A4R, B5R, 8K, 16KR)Stapling*4:
100 sets or 1550 sheets (8-1/2 x 11, A4, B5, 
16K)
50 sets or 650 sheets (11 x 17, 8-1/2 x 14, 
8-1/2 x 13-1/2, 8-1/2 x 13-2/5, 8-1/2 x 13, 
8-1/2 x 11R, A3, B4, A4R, 8K)
Power supplySupplied from the machine
Dimensions25-25/64 (W) x 25-25/64 (D) x 43-19/64 (H) (645 mm (W) x 645 mm (D) x 1100 mm (H)) 
(When tray is extended)
WeightApprox. 99.3 lbs. (45 kg)
Stapler section
Allowed paper sizes for 
stapling11 x 17, 8-1/2 x 14, 8-1/2 x 13-1/2, 8-1/2 x 13-2/5, 8-1/2 x 13, 8-1/2 x 11, 8-1/2 x 11R, 
A3, B4, A4, A4R, B5, 8K, 16K
(Three stapling positions: one staple at bottom left corner, one staple at top left corner, and two staples.)
Maximum number of 
sheets for stapling*5
50 sheets (8-1/2 x 11, A4, B5, 16K
30 sheets (11 x 17, 8-1/2 x 14, 8-1/2 x 13-1/2, 8-1/2 x 13-2/5, 8-1/2 x 13, 8-1/2 x 11 A3, 
B4, A4R, 8K)
(30 sheets when the sheets are the same width but different lengths.)
Note:
Special media such as transparency film and label sheets cannot be stapled or punched.
mx5001_us_saf.fm  13 ページ  ２００８年９月２４日　水曜日　午前９時４５分