Sharp Mx 4100n Owners Manual

							7-19
SYSTEM SETTINGS
Contents
Program
If you frequently use the same settings and/or functions to transmit to the same destination or destinations, the settings 
and destinations can be stored in a program. This allows the settings and destinations to be selected by simply selecting 
the program.
When the [Program] key is touched, the following screen appears.
[Add New] key
Use this to add a new program.List display
This displays a list of the currently stored programs. A 
program can be selected to open an edit/delete screen 
for the program.
Storing a program
Touch the [Add New] key in the above screen to open a registration screen. Up to 48 programs can be stored.
For more information, see Settings (page 7-19).
Editing and deleting programs
A program can be selected from the list in the above screen to open an edit/delete screen for the program.
For more information, see Settings (page 7-19).
Delete a program with the [Delete] key.
Settings
ProgramSystem SettingsBack
Program 1
Program 3
Program 5
Program 7
Program 9
Program 11
Program 2
Program 4
Program 6
Program 8
Program 10
Program 12
Add New
 A timer setting cannot be included in a program.
 At least one one-touch key must be specified in a program or the program cannot be stored.
ItemDescription
Program Number
Set the number to be assigned to the program. The lowest available number is 
automatically entered. To change the number, enter a number from 01 to 48. A 
number that has already been stored cannot be used.
Program NameEnter a maximum of 36 characters for the program name.
AddressSelect the address(es) to be used in the program from the address book. Up to 500 
destinations can be stored in one program. 
Address Book screenThis displays a list of the currently stored addresses.
Condition SettingsTouch the [Setup] key to open the condition settings screen for an address.
Address Mode SettingSelect the mode in which the address is used (Internet fax, scan, etc.) When a mode 
is selected, the settings for that mode appear.
Mode SettingsFrequently used settings can be stored in the same way as when they are selected 
for a mode. 
						

							7-20
SYSTEM SETTINGS
Contents
Fax Data Receive/Forward
This section explains settings for reception and forwarding. Touch the [Fax Data Receive/Forward] key and configure 
the settings.
I-Fax Settings
These settings can be configured when the Internet fax expansion kit is installed.
Reception Start
Touch this key to immediately connect to your mail server (POP3 server) and check for received Internet faxes. If you 
have received Internet faxes, the faxes will be retrieved and printed.
Manual Reception Key in Initial Screen
This displays the [I-Fax Manual Reception] key in the base screen of Internet fax mode.
Forward Received Data
When the machine cannot print because it is out of paper or out of toner, received faxes can be forwarded to another 
Internet fax machine.
For explanations of settings related to the fax function, see SYSTEM SETTINGS FOR FAX (page 7-98).
To use this function, POP3 server settings must be configured. Configure these settings in the screen that appears when 
[Application Settings] - [Internet Fax Settings] is selected in the Web page menu.
 To store a forwarding address, see Set Address for Data Forwarding (page 7-84) in the system settings (administrator).
 If forwarding was not successful because the transmission was canceled or a communication error occurred, the faxes that 
were to be forwarded will return to the print queue on the machine.
 If the initial pages of a fax were successfully printed, only those pages that were not printed will be forwarded.
 Forwarding is not possible if no faxes were received or a forwarding address is not programmed.
Hold Setting for Received Data Print (page 7-77) is enabled, you will be prompted to enter a password. Enter the 
correct password with the numeric keys.
To cancel forwarding...
Press the [JOB STATUS] key, and then cancel the forwarding job in the same way as a transmission job. 
						

							7-21
SYSTEM SETTINGS
Contents
Printer Condition Settings
The Printer Condition Settings are used to configure basic printer settings and settings for printing from a DOS 
application. To configure the settings, touch the [Printer Condition Settings] key.
Printer Default Settings
The default settings are used to set advanced print conditions for printing in an environment where the print driver is not 
used (such as printing from MS-DOS or from a computer that does not have the provided print driver installed). 
Settings
When printing using the printer driver, the printer driver settings take precedence over the printer condition settings.
ItemSelections
Copies1 - 999 sets
Orientation Portrait
 Horizontal
Default Paper Size11 x 17, 8-1/2 x 14, 8-1/2 x 13, 8-1/2 x 11, 7-1/4 x 10-1/2, 5-1/2 x 8-1/2, A3, 
B4, A4, B5, A5, 8k, 16k
Default Output Tray

 Offset Tray*1
 Finisher Upper Tray*2
 Finisher Lower Tray*2
 Right Tray
Default Paper TypePlain Paper, Letter Head, Pre-Printed, Pre-Punched, Recycle Paper, Color
Initial Resolution Setting
 600 dpi
 600 dpi (High Quality)
 1200 dpi
Disable Blank Page Print  (Disabled)
  (Enabled)
Line Thickness*30-9
2-Sided Print
 1-Sided
 2-Sided (Book)
 2-Sided (Tablet)
Color Mode
 Black & White
N-Up Print*4


Fit To Page*5  (Use Fit to Page)
  (Do not use Fit to Page) 
						

							7-22
SYSTEM SETTINGS
Contents
*1 When a saddle stitch finisher or finisher is installed.
*2 When a finisher (large stacker) is installed.
*3 This setting is used to adjust the line width of vector graphics (black & white printing only). Except for CAD and other 
specialized uses, there is normally no need to change this setting. When 0 is selected, all lines are printed at a 
width of 1 dot.
*4 Paper sizes that can be used with this function are A3, B4, A4, 11 x 17, 8-1/2 x 14, and 8-1/2 x 11. (This function 
may not take effect with some print methods.)
*5 Only effective when printing PDF, JPEG, and TIFF files.
PCL Settings
This is used to set the symbol sets, fonts, and line feed code used in a PCL environment.
Settings
Output
  (Use Print per Unit)
  (Do not use Print per Unit)
 Staple Position*
1: None, 1 Staple at Back, 2 Staples, 2 Staples (Top)

  (Do not use Punch)
Quick File  (Disabled)
  (Enabled)
ItemDescriptionSelections
PCL Symbol Set SettingSpecify the symbol set used for 
printing.Select from 35 items.
PCL Font Setting
Use this to select the font used for 
printing. Internal Font
 Extended Font
(List of internal fonts when extended fonts are not 
installed.)
PCL Line Feed Code
This setting is used to select how 
the printer responds when a line 
feed command is received. 0.CR=CR; LF=LF; FF=FF
 1.CR=CR+LF; LF=LF;FF=FF
 2.CR=CR; LF=CR+LF; FF=CR+FF
 3.CR=CR+LF; LF=CR+LF; FF=CR+FF
Wide A4
When this is enabled, 80 
characters per line can be printed 
on A4 size paper using a 10-pitch 
font. (When this setting is 
disabled, up to 78 characters can 
be printed per line.)  (Enabled)
  (Disabled)
ItemSelections 
						

							7-23
SYSTEM SETTINGS
Contents
PostScript Setting
When an error occurs during PostScript printing, these settings determine whether or not an error notice is printed and 
whether or not the PostScript data is received in binary format.
Settings
ItemDescriptionSelections
Print PS Error
When a PS (PostScript) error 
occurs during PostScript printing, 
this setting determines whether or 
not an error notice is printed.  (Enabled)
  (Disabled)
Binary ProcessingReceive PostScript data in binary 
format.  (Enabled)
  (Disabled)
This setting can be configured when the PS3 expansion kit is installed. 
						

							
7-24
SYSTEM SETTINGS
Contents
Document Filing Control
Document Filing Control is used to create, edit, and delete custom folders for document filin g. Touch the [Document 
Filing Control] key to  configure the settings.
When the [Document Filing Cont rol] key is touched, the following screen will appear.
• [Add New] key
Use this to add a new custom folder. 
List display
This displays a list of the currently configured custom 
folders. A folder can be selected to open an edit/delete 
screen for the folder.
Creating a custom folder
Touch the [Add New] key in the above screen to open a registration screen. Up to 1000 custom folders can be created.
For more information, see  Settings (page 7-24).
Editing/deleting a custom folder
A custom folder can be selected from the list in the above screen to open an edit/delete screen for the folder.
For more information, see  Settings (page 7-24).
Delete a folder with the [Delete] key.
Settings
Folder ListBack
User 1
User 3
User 5
User 7
User 9
User 2
User 4
User 6
User 8
User 10
Add New
SortUpAll FoldersEFGHIABCDJKLMNOPQRSTUVWXYZ
12
 If the folder has a password, the correct passwor d must be entered before a file can be deleted.
 A folder that contains files c annot be deleted. Either move the files to a diff erent folder or delete them before deleting the 
folder.
ItemDescription
Folder NameEnter a name (maximum of 28 characters) for the custom folder to be created. A 
name cannot be stored if it is already being used for another folder.
Initial of FolderEnter up to 10 characters for the initials. The initials you enter here determine the 
position of the one-touch key in the alphabetical index.
Password of FolderTo set a password for the folder, enter the desired number (5 to 8 digits).
Select User NameSelect the desired user name from the user list. 
						

							7-25
SYSTEM SETTINGS
Contents
USB-Device Check
This lets you check the connection when a USB device is connected to the machine. Touch the [USB-Device Check] key 
to check the connection.
User Control
This section explains settings for user control. Touch the [User Control] key to configure the settings.
Modify User Information
The information of the currently logged in user can be edited.
Settings
The status of a USB device that is not compatible with the machine will not appear.
 User Control settings can only be configured when User Authentication Setting (page 7-45) is enabled.
 Depending on the user that logged in, it may not be possible to use the settings below.
ItemDescription
User Name
Edit the name of the user (max. 32 characters). This user name is used as the key 
name in the login screen, the document filing user name, and the sender name. (The 
user name must be unique.)
InitialEdit the initials (maximum of 10 characters). The initials determine where the user 
name will appear in the user name list.
IndexSelect the desired custom index. The custom index names are the same as those in 
the address book.
Login NameThis cannot be edited.
PasswordEnter the password used for user authentication by login name and password (1 to 
32 characters). (The password can be omitted.)
My FolderThis cannot be edited.
E-mail AddressThis cannot be edited.
Authentication SettingsThis cannot be edited.
Pages Limit GroupThis cannot be edited.
Authority GroupThis cannot be edited.
Favorite Operation GroupThe favorite operation group that will be applied at login appears.
Check with your administrator for the settings of the Favorite Operation Groups.
User NumberThis cannot be edited.
Deleting an accountThis cannot be edited.
The items that appear will vary depending on the user authentication method that is enabled. 
						

							7-26
SYSTEM SETTINGS
Contents
.
This section explains the system settings that are configured by the administrator of the machine.
Accessing the System Settings (Administrator)
To access the system settings (administrator), the administrator must log in as explained below.
When User Authentication is not Enabled
When User Authentication Setting (page 7-45) is not enabled, follow the procedure below to log in.
SYSTEM SETTINGS 
(ADMINISTRATOR)
1
Touch the [Admin Password] key.
2
Log in.
(1) Touch the [Password] text box and enter 
the administrator password.
(2) Touch the [OK] key.
This completes the administrator login procedure. The system settings (administrator) can be used.
 User authentication is initially disabled (factory default setting).
To logout...
Touch the [Logout] key in the top right corner of the screen. You can also touch the [Exit] key to quit the system settings.
(If Auto Clear activates, logout will automatically take place.)
System SettingsExitAdmin Password
Total CountDefault Settings
Address Control
USB-Device Check
List Print
(User)
Fax Data
Receive/ForwardPaper Tray
Settings
Printer Condition
SettingsDocument Filing
Control
System
 SettingsAdmin Password
Enter the administrator password. (From 5 to 32 characters)
Press here for keyboard.Password
CancelOK
(1)(2) 
						

							
7-27
SYSTEM SETTINGS
Contents
When User Authentication is Enabled
When User Authentication Setting  (page 7-45) is enabled, follow the procedure below to log in.
When user authentication is by lo gin name and password (and e-mail 
address)
When auto login is enabled, the login screen will not appear.
Administrator login is performed in the user selection screen. For more information on the login procedure when user 
authentication is enabled, see  USER AUTHENTICATION (page 1-17) in 1. BEFORE USING THE MACHINE.
1
Touch the [Admin Login] key.
2
Log in.
(1) Touch the [Password] key.
Enter the administrator password in the administrator 
password entry screen.
(2) Touch the [OK] key.
• If login name / password / e-mail address is selected fo r the authentication method, the [E-mail Address] key will 
appear below the User Name.
 For the factory default administrato r password, see TO THE ADMINISTRATO R OF THE MACHINE in the Safety 
Guide.
 This completes the administrator  login procedure. The system settings (admin istrator) can be used.
12
Device Account Mode User SelectionBack
12186
Direct Entry
User
ABC
Admin Login
12
Name 1Name 2
Name 3Name 4
Name 5Name 6
Name 7Name 8
Name 9Name 10
Name 11Name 12
AllEFGHABCDIJKLMNOPQRSTUVWXYZetc.
User AuthenticationOK
Login Name
Login Locally
User NameAdministrator
Password
Auth to:
(2)(1) 
						

							7-28
SYSTEM SETTINGS
Contents Login by user number
Touch the [Admin Login] key.
Enter the administrator password in the administrator password 
entry screen.
This completes the administrator login procedure. The system 
settings (administrator) can be used.
 In addition to login by touching the [Admin Login] key, the system settings (administrator) can also be accessed when login 
is performed by selecting a user with administrator rights from the user list or by entering a user number with administrator 
rights. For more information on login procedures when user authentication is enabled, see USER AUTHENTICATION 
(page 1-17) in 1. BEFORE USING THE MACHINE.
To logout...
Press the [LOGOUT] ( ) key. (Except when entering a fax number.)
(If Auto Clear activates, logout will automatically take place.)
User AuthenticationOK
Admin Login