Home
>
Land Rover
>
Automobile
>
Land Rover Range Rover 2002my On Workshop Procedures Lm 6th Edition Nas Rover Manual
Land Rover Range Rover 2002my On Workshop Procedures Lm 6th Edition Nas Rover Manual
Have a look at the manual Land Rover Range Rover 2002my On Workshop Procedures Lm 6th Edition Nas Rover Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 364 Land Rover manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
SEATS 76-5-32 REPAIRS 21.Remove 19 hog rings securing squab cover to pad, remove cover. 22.Release retaining plate securing headrest finisher to squab cover, remove finisher. Refit 1.Fit headrest finisher to squab cover and secure with retaining plate. 2.Position squab cover to pad and secure with 19 hog rings. 3.Fit squab cover and pad to frame. 4.Fit 4 retaining strips securing both sides of squab cover to frame. 5.Position and fit squab assembly to seat assembly. 6.Fit squab frame to seat frame, secure with Torx bolts tighten to 25 Nm (18 lbf.ft). 7.Secure squab harness to retaining clips 8.Fit retaining strips securing both sides of lower squab cover. 9.Connect multiplug to heated seat circuit. 10.Connect lumbar harness multiplugs to pump and valve. 11.Connect multiplugs to headrest and squab motor.12.Fit retaining strip securing lower squab cover to frame. 13.Fit headrest and secure to motor housing. 14.Position upper finisher and secure retaining clips. 15.Secure squab cover beading to finisher. 16.Secure squab cover velcro strip 17.Connect tension straps securing upper squab cover. 18.Position lower finisher and secure retaining clips 19.Fit screws securing lower squab finisher. 20.Fit backboard tension straps to under seat retaining clips. 21.Fit seat assembly. + SEATS, REPAIRS, Front seat.
SEATS REPAIRS 76-5-33 Cover - squab - front seat $% 78.90.08 Remove 1.Remove seat assembly. + SEATS, REPAIRS, Front seat. 2.Remove Allen bolt securing arm rest. 3.Remove armrest from boss. 4.Remove headrest. 5.Release 3 backboard tension straps from under seat.6.Release staples securing squab cover to lower backboard. 7.Release squab side cover from both sides of backboard. 8.Release 2 studs securing lower half of backboard. 9.Release backboard from seat. M78 0613
SEATS 76-5-34 REPAIRS 10.Disconnect harness multiplugs from lumbar pump and valve. 11.Disconnect multiplug from heated seat circuit. 12.Release harness from retaining clip and feed harness through squab cover. 13.Remove 2 Torx bolts and remove squab frame from seat frame.14.Raise front of squab cover to gain access to head rest guides. 15.Release headrest retaining clips, remove headrest guides. 16.Remove squab cover and pad from frame. 17.Remove and discard 12 hog rings and remove cover from pad. Refit 1.Position squab cover to pad and secure with hog rings. 2.Position and fit squab cover to frame. 3.Fit and secure headrest guides in squab frame. 4.Position squab frame to seat frame, fit Torx bolts tighten to 25 Nm (18 lbf.ft). 5.Route lumbar harness through squab cover and secure to frame. 6.Connect multiplug to heated seat circuit. 7.Connect lumbar harness multiplugs to pump and valve. 8.Position backboard to seat assembly, fit studs securing lower of backboard. 9.Position and fit both sides of squab cover to backboard. M78 0616
SEATS REPAIRS 76-5-35 10.Position lower squab cover to backboard and staple. 11.Fit backboard tension straps to under seat retaining clips. 12.Fit armrest to boss and secure with Allen bolt, tighten to 25 Nm (18 lbf.ft). 13.Fit seat assembly. + SEATS, REPAIRS, Front seat. Cover - squab - rear seat - side - LH $% 78.90.12 Remove 1.Remove seat base finisher. + SEATS, REPAIRS, Finisher - seat base rear. 2.Remove seat fold mechanism. + SEATS, REPAIRS, Hinge - rear seat - side. 3.Remove rear squab finisher. + SEATS, REPAIRS, Finisher - rear seat squab. 4.Remove Torx bolt securing squab frame to seat frame, separate frames. 5.Remove armrest front finisher assembly. + SEATS, REPAIRS, Finisher - arm rest - rear seat - front. 6.Disconnect multiplug from heated squab. 7.Release finisher from retaining clips and remove. 8.Release seat cover beading from sides and front. M78 0646
SEATS 76-5-36 REPAIRS 9.Raise seat cover and cushion, remove and discard Torx bolt securing seat belt anchor point to frame. 10.Pull seatbelt through cushion and cover, remove seat base. 11.Remove 2 screws securing seat belt finisher, remove finisher. 12.Release beading securing squab cover to sides and bottom of frame. 13.Carefully release 4 clips securing seat release button escutcheon, remove escutcheon. 14.Raise squab cover and cushion to gain access to headrest guides. 15.Release 3 clips securing headrest guides to frame, remove guides.16.Remove cover and cushion assembly from frame and feed seat belt through assembly. 17.Remove 16 hog rings securing cover to cushion, remove cover. Refit 1.Position cover to cushion and secure with hog rings. 2.Feed seat belt through cover and cushion assembly and fit assembly to frame. 3.Position and fit headrest guides in squab assembly. 4.Position and fit seat fold release button escutcheon. 5.Secure squab cover beading to sides and bottom of frame. 6.Position seatbelt finisher and secure with screws. 7.Fit seatbelt through cover and cushion assembly. 8.Position seatbelt to frame and fit Torx bolt, tighten to 48 Nm (35 lbf.ft). 9.Fit seat cover beading to sides and front. 10.Connect squab cover heated seat circuit multiplug. 11.Fit armrest front finisher assembly. + SEATS, REPAIRS, Finisher - arm rest - rear seat - front. 12.Position squab frame to seat frame and secure LH side with Torx bolt, tighten to 25 Nm (18 lbf.ft). 13.Fit rear squab finisher. + SEATS, REPAIRS, Finisher - rear seat squab. 14.Fit seat fold mechanism. + SEATS, REPAIRS, Hinge - rear seat - side. 15.Fit seat base finisher. + SEATS, REPAIRS, Finisher - seat base rear.
SEATS REPAIRS 76-5-37 Cover - squab - rear seat - RH $% 78.90.13 Remove 1.Remove seat base finisher. + SEATS, REPAIRS, Finisher - seat base rear. 2.Remove seat fold mechanism. + SEATS, REPAIRS, Hinge - rear seat - side. 3.Remove Torx bolt securing squab frame to seat frame, separate frames. 4.Disconnect multiplug to heated squab. 5.Remove rear squab finisher. + SEATS, REPAIRS, Finisher - rear seat squab. 6.Release beading securing squab cover to sides and bottom of frame.7.Carefully release 4 clips securing seat release button escutcheon, remove escutcheon. 8.Raise squab cover and cushion to gain access to headrest guides. 9.Release 3 clips securing headrest guides to frame, remove guides. 10.Remove cover and cushion assembly from frame. M78 0646
SEATS 76-5-38 REPAIRS 11.Remove 16 hog rings securing cover to cushion, remove cover. Refit 1.Position cover to cushion and secure with hog rings. 2.Position and fit headrest guides in squab assembly. 3.Position and fit seat fold release button escutcheon. 4.Secure squab cover beading to sides and bottom of frame. 5.Fit rear squab finisher. + SEATS, REPAIRS, Finisher - rear seat squab. 6.Position squab frame to seat frame and secure LH side with Torx bolt, tighten to 25 Nm (18 lbf.ft). 7.Connect squab cover heated seat circuit multiplug. 8.Fit seat fold mechanism. + SEATS, REPAIRS, Hinge - rear seat - side. 9.Fit seat base finisher. + SEATS, REPAIRS, Finisher - seat base rear. Hinge - rear seat - side $% 78.90.43 Remove 1.Fold rear seat forward. 2.Remove 3 screws securing mechanism finisher, remove finisher. 3.Remove and discard 2 Torx bolts securing mechanism to squab frame. 4.Remove 2 Allen bolts securing mechanism to seat frame, remove mechanism.
SEATS REPAIRS 76-5-39 5.Remove and discard Torx bolt securing seat belt stalk, remove stalk. Refit 1.Position seat belt stalk and secure with Torx bolt, tighten to 31 Nm (23 lbf.ft). 2.Position mechanism to seat frame and secure with Allen bolts, tighten to 25 Nm (18 lbf.ft). 3.Position squab frame to mechanism and secure with Torx bolts, tighten to 25 Nm (18 lbf.ft). 4.Position mechanism finisher and secure with screws. 5.Reposition rear seat.
SUNROOF ADJUSTMENT 76-6-1 SUNROOF ADJUST ME NT Sun roof - align to roof panel & adjust $% 76.84.82 Check 1.With sunroof closed, check alignment of glass to roof panel. The glass should be central in its aperture. Profile of sunroof to body: lfront edge of sunroof = flush or up to 1.0 mm (0.040 in) lower lrear edge of sunroof = flush or up to 1.0 mm (0.040 in) higher Adjust 1.Open sunroof blind. 2.Operate switch to raise sunroof fully. 3.Carefully release upper edges of gaiters from sunroof glass. 4.Close sunroof. 5.Loosen 6 Torx screws securing sunroof glass. 6.Align glass to roof and tighten Torx screws to 6 Nm (4.4 lbf.ft). 7.Operate switch to raise sunroof fully. 8.Fit gaiters to sunroof glass. 9.Close sunroof.10.Close sunroof blind.