Home
>
Land Rover
>
Automobile
>
Land Rover Range Rover 2002my On Workshop Procedures Lm 6th Edition Nas Rover Manual
Land Rover Range Rover 2002my On Workshop Procedures Lm 6th Edition Nas Rover Manual
Have a look at the manual Land Rover Range Rover 2002my On Workshop Procedures Lm 6th Edition Nas Rover Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 364 Land Rover manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
INTERIOR FITTINGS 76-3-6 REPAIRS Trim finisher - E post $% 76.13.32 Remove 1.Open tailgate. 2.Release aperture seal. 3.Release 4 fixings securing E post finisher and carefully remove finisher. 4.Remove fixings from finisher. Refit 1.Fit new fixings to finisher. 2.Fit finisher and secure fixings. 3.Fit seal to aperture. Centre console $% 76.25.01 Remove 1.Remove centre console finisher. + INTERIOR FITTINGS, REPAIRS, Finisher - console. 2.Remove both centre console closing panels. + INTERIOR FITTINGS, REPAIRS, Closing panel - centre console. 3.Remove 2 Torx screws securing large cubby box liner, remove liner. 4.Remove 2 Torx screws securing ignition switch to centre console. 5.Remove 4 Torx screws securing centre console to fascia.
INTERIOR FITTINGS REPAIRS 76-3-7 6.Remove 2 Torx screws and collect washers from base of large cubby box. 7.Remove 2 screws securing centre console rear closing panel. Release clips and remove panel. 8.Raise rear of centre console, disconnect 3 multiplugs from centre console and collect air duct adaptor. 9.Disconnect 3 Lucar connectors from accessory power socket.10.Carefully remove centre console. CAUTION: Care must be taken to protect painted and veneered surfaces. Refit 1.Position centre console and connect multiplugs to rear of console. Fit air duct adaptor and align centre console to mountings. 2.Secure centre console with screws. 3.Fit rear closing panel and secure with clips and screws. 4.Position ignition switch and secure with screws. 5.Fit cubby box and secure with Torx screws. 6.Fit both centre console closing panels. + INTERIOR FITTINGS, REPAIRS, Closing panel - centre console. 7.Fit centre console finisher. + INTERIOR FITTINGS, REPAIRS, Finisher - console. M76 4349
INTERIOR FITTINGS 76-3-8 REPAIRS Console - headlining - front $% 76.25.02 Remove 1.Open spectacle holder, remove 2 screws securing console and release console from headlining. 2.Disconnect multiplugs from switches and lamp. Remove console assembly. NOTE: Do not carry out further dismantling if component is removed for access only. 3.Remove lamp from console. 4.Remove switches from console. 5.Remove 2 retaining clips from console.Refit 1.Fit retaining clips to console. 2.Fit switches to console. 3.Fit lamp to console. 4.Position front console and connect multiplugs. 5.Fit console to headlining and secure with screws. 6.Close holder. M76 4389
INTERIOR FITTINGS REPAIRS 76-3-9 Finisher - console $% 76.25.07 Remove 1.Remove gear selector cover. + INTERIOR FITTINGS, REPAIRS, Cover - automatic transmission selector. 2.Release gaiter from handbrake lever grip. 3.Release and remove handbrake lever grip. 4.Open cubby box lids, carefully release clips and remove finisher. 5.Remove 6 Torx screws securing finisher to centre console, fully apply handbrake. 6.Release finisher from clips, raise and disconnect 3 Lucar connectors from accessory power socket. 7.Disconnect multiplug from closing panel lamp assembly. 8.Remove centre console finisher. NOTE: Do not carry out further dismantling if component is removed for access only. 9.Remove 2 Torx screws securing accessory socket and remove socket. 10.Remove 4 Torx screws securing cubby box and remove box. 11.Remove 3 Torx screws securing cup holder and remove cup holder. 12.Remove handbrake lever gaiter Refit 1.Fit cup holder and secure with Torx screws. 2.Fit cubby box and secure with Torx screws. 3.Fit accessory socket and secure with Torx screws. 4.Fit handbrake lever gaiter.
INTERIOR FITTINGS 76-3-10 REPAIRS 5.Position centre console finisher and connect Lucars. 6.Connect multiplug to closing panel lamp assembly. 7.Fit finisher and secure with Torx screws. 8.Fit handbrake lever grip and secure gaiter. 9.Fit and secure small cubby box finisher. 10.Close cubby box lids. 11.Fit gear selector cover. + INTERIOR FITTINGS, REPAIRS, Cover - automatic transmission selector. Console - headlining - rear $% 76.25.08 Remove 1.Carefully release rear console from headlining. 2.Disconnect multiplug from interior lamp. 3.Disconnect multiplug from ultrasonic sensor and remove console assembly. NOTE: Do not carry out further dismantling if component is removed for access only. 4.Carefully release and remove ultrasonic sensor and module. 5.Remove lamp from console. Refit 1.Fit lamp to console. 2.Fit module and ultrasonic sensor to console. 3.Position console assembly and connect multiplugs. 4.Fit rear console to headlining. M76 4387
INTERIOR FITTINGS REPAIRS 76-3-11 Cover - automatic transmission selector $% 76.25.09 Remove 1.Turn ignition key to position II, depress brake pedal and move gear lever to D drive, turn ignition off. 2.Release clips and gear selector cover from centre console. 3.Carefully disconnect 4 multiplugs from gear selector panel. 4.Remove gear lever knob and cover by pulling sharply upward. 5.Release clips securing gear lever gaiter to centre console cover, remove knob and gaiter. Refit 1.Position cover and connect multiplugs, secure cover to centre console. 2.Fit gear lever knob to gear lever. 3.Fit gaiter to centre console and secure with clips. 4.Turn ignition key to position II, return gear lever to Park, turn ignition off. Closing panel - centre console $% 76.25.31 Remove 1.Remove screw securing closing panel to fascia. 2.Release 2 clips securing closing panel and remove from lower fascia. NOTE: Do not carry out further dismantling if component is removed for access only. 3.Remove 6 screws securing trim finisher to closing panel. Remove finisher. 4.Remove damper. 5.Remove 2 trim clips. Refit 1.Fit trim clips to finisher. 2.Fit damper. 3.Fit trim finisher to closing panel and secure with screws. 4.Fit closing panel and tighten screw, secure to clips.
INTERIOR FITTINGS 76-3-12 REPAIRS Switch panel - air suspension $% 76.25.41 Remove 1.Remove heating control assembly. + HEATING AND VENTILATION, REPAIRS, Controls - heater (ECU). 2.Carefully release clips securing air suspension switch panel, disconnect multiplug and remove the panel. Refit 1.Position air suspension switch panel, connect multiplug and secure panel to carrier. 2.Fit heating control assembly. + HEATING AND VENTILATION, REPAIRS, Controls - heater (ECU). Top rail - fascia $% 76.46.04 Remove 1.Remove drivers side upper trim finisher. + INTERIOR FITTINGS, REPAIRS, Finisher - upper - drivers side. 2.Remove passenger side upper trim finisher. + INTERIOR FITTINGS, REPAIRS, Finisher - upper - passengers side. 3.Carefully release clips securing centre grille to top rail. Remove grille. 4.Remove 11 Torx screws securing top rail to fascia, carefully pull top rail rearward and release. 5.Disconnect speaker multiplug and remove top rail. NOTE: Do not carry out further dismantling if component is removed for access only. 6.Remove 4 Torx screws securing speaker to top rail and remove speaker.
INTERIOR FITTINGS REPAIRS 76-3-13 7.Remove 4 Torx screws securing instrument pack finisher, remove finisher. Refit 1.Fit instrument pack finisher to top rail and secure with Torx screws. 2.Fit speaker and secure with screws. 3.Position top rail, connect speaker multiplug. Secure rail with Torx screws. 4.Position and secure centre grille. 5.Fit drivers side upper trim finisher. + INTERIOR FITTINGS, REPAIRS, Finisher - upper - drivers side. 6.Fit passenger side upper finisher. + INTERIOR FITTINGS, REPAIRS, Finisher - upper - passengers side. Shroud - lower - fascia $% 76.46.05 Before disconnecting the battery, ensure all text and cautions in the battery disconnection section are observed. + GENERAL INFORMATION, Electrical Precautions. Remove 1.Remove rotary coupler. + RESTRAINT SYSTEMS, REPAIRS, Rotary coupler. 2.Remove glove box. + INTERIOR FITTINGS, REPAIRS, Glove box. 3.Remove centre air vent. + HEATING AND VENTILATION, REPAIRS, Ventilator(s) - centre. 4.Remove drivers side upper trim finisher. + INTERIOR FITTINGS, REPAIRS, Finisher - upper - drivers side. 5.Remove drivers side lower trim finisher. + INTERIOR FITTINGS, REPAIRS, Finisher - lower - drivers side. 6.Remove 6 Torx screws securing lower fascia shroud. 7.Carefully release 7 clips securing shroud to carrier assembly. Remove shroud. NOTE: Do not carry out further dismantling if component is removed for access only. 8.Remove 7 trim fasteners from shroud. 9.Remove 4 retaining clips from shroud. Refit 1.Fit clips to shroud. 2.Fit fasteners to shroud. M76 4320
INTERIOR FITTINGS 76-3-14 REPAIRS 3.Position shroud to carrier, fit and secure with clips and screws. 4.Fit drivers side lower trim finisher. + INTERIOR FITTINGS, REPAIRS, Finisher - lower - drivers side. 5.Fit drivers side upper trim finisher. + INTERIOR FITTINGS, REPAIRS, Finisher - upper - drivers side. 6.Fit centre air vent. + HEATING AND VENTILATION, REPAIRS, Ventilator(s) - centre. 7.Fit glove box. + INTERIOR FITTINGS, REPAIRS, Glove box. 8.Fit rotary coupler. + RESTRAINT SYSTEMS, REPAIRS, Rotary coupler. Closing panel - fascia end $% 76.46.11 Remove 1.Release sufficient door aperture seal to access closing panel. 2.Release 3 clips securing end closing panel to fascia and carefully remove panel. NOTE: Do not carry out further dismantling if component is removed for access only. 3.Remove 3 retaining clips from closing panel. Refit 1.Fit retaining clips to closing panel. 2.Position closing panel to fascia, align and secure clips. 3.Fit seal to door aperture.
INTERIOR FITTINGS REPAIRS 76-3-15 Finisher - upper - drivers side $% 76.46.12 Remove 1.Remove fascia end closing panel. + INTERIOR FITTINGS, REPAIRS, Closing panel - fascia end. 2.Remove face level air vent. + HEATING AND VENTILATION, REPAIRS, Fresh air vent - face level. 3.Remove A post upper trim finisher. + INTERIOR FITTINGS, REPAIRS, Trim finisher - A post - upper. 4.Remove 3 Torx screws securing upper finisher to fascia. 5.Release upper finisher from fascia and disconnect switch multiplug. 6.Disconnect footwell lamp multiplug. 7.Remove upper finisher. NOTE: Do not carry out further dismantling if component is removed for access only. 8.Remove switch assembly from finisher. 9.Depress clips and remove footwell lamp assembly from finisher.Refit 1.Fit footwell lamp assembly to finisher. 2.Fit switch assembly to finisher. 3.Connect multiplugs. 4.Fit finisher to fascia and secure with screws. 5.Fit face level air vents. + HEATING AND VENTILATION, REPAIRS, Fresh air vent - face level. 6.Fit fascia end closing panels. + INTERIOR FITTINGS, REPAIRS, Closing panel - fascia end. 7.Fit A post finisher. + INTERIOR FITTINGS, REPAIRS, Trim finisher - A post - upper.