Home
>
Land Rover
>
Automobile
>
Land Rover Range Rover 2002my On Workshop Procedures Lm 6th Edition Nas Rover Manual
Land Rover Range Rover 2002my On Workshop Procedures Lm 6th Edition Nas Rover Manual
Have a look at the manual Land Rover Range Rover 2002my On Workshop Procedures Lm 6th Edition Nas Rover Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 364 Land Rover manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
ENGINE MANAGEMENT SYSTEM - V8 18-2-10 REPAIRS Sensor - camshaft position (CMP) - RH $% 18.30.26 Before disconnecting the battery, ensure all text and cautions in the battery disconnection section are observed. + GENERAL INFORMATION, Electrical Precautions. Remove 1.Disconnect battery earth lead. 2.Remove air intake hose. + ENGINE MANAGEMENT SYSTEM - V8, REPAIRS, Hose - air flow meter to throttle body. 3.Cut 3 cable ties to release CMP sensor harness. 4.Disconnect multiplug from CMP sensor.5.Remove bolt securing CMP sensor and remove sensor. Discard O ring. Refit 1.Clean CMP sensor and mating face. 2.Fit new O ring. 3.Fit CMP sensor, fit bolt and tighten to 10 Nm (7 lbf.ft). 4.Secure CMP sensor harness with 3 cable ties. 5.Connect multiplug to CMP sensor. 6.Connect air intake hose. + ENGINE MANAGEMENT SYSTEM - V8, REPAIRS, Hose - air flow meter to throttle body. 7.Connect battery earth lead. 8.If a replacement sensor has been fitted, re-set adaptions using TestBook/T4. M86 5760 M86 5747
ENGINE MANAGEMENT SYSTEM - V8 REPAIRS 18-2-11 Sensor - knock (KS) - LH $% 18.30.28 Before disconnecting the battery, ensure all text and cautions in the battery disconnection section are observed. + GENERAL INFORMATION, Electrical Precautions. Remove 1.Disconnect battery earth lead. 2.Remove coolant pump to coolant manifold pipes. + COOLING SYSTEM - V8, REPAIRS, Pipe(s) - coolant pump to coolant manifold. 3.Remove 2 bolts securing KS to cylinder block, remove sensors. Refit 1.Clean KS and mating faces on cylinder block. 2.Position KS to engine block, fit bolts securing KS and tighten to 20 Nm (15 lbf.ft). 3.Fit coolant pump to coolant manifold pipes. + COOLING SYSTEM - V8, REPAIRS, Pipe(s) - coolant pump to coolant manifold. 4.Connect battery earth lead. 5.If a replacement sensor has been fitted, re-set adaptions using TestBook/T4. Sensor - knock (KS) - RH $% 18.30.30 Before disconnecting the battery, ensure all text and cautions in the battery disconnection section are observed. + GENERAL INFORMATION, Electrical Precautions. Remove 1.Disconnect battery earth lead. 2.Remove inlet manifold. + MANIFOLD AND EXHAUST SYSTEM - V8, REPAIRS, Gasket(s) - inlet manifold. 3.Remove 2 bolts securing KS to cylinder block, remove sensors. Refit 1.Clean KS and mating faces on cylinder block. 2.Position KS to engine block, fit bolts securing KS and tighten to 20 Nm (15 lbf.ft). 3.Fit inlet manifold. + MANIFOLD AND EXHAUST SYSTEM - V8, REPAIRS, Gasket(s) - inlet manifold. 4.Connect battery earth lead. 5.If a replacement sensor has been fitted, re-set adaptions using TestBook/T4.
ENGINE MANAGEMENT SYSTEM - V8 18-2-12 REPAIRS Sensor - temperature - E box $% 18.30.77 Before disconnecting the battery, ensure all text and cautions in the battery disconnection section are observed. + GENERAL INFORMATION, Electrical Precautions. Remove 1.Disconnect battery earth lead. 2.Remove 10 Allen screws securing E box cover and remove cover. 3.Disconnect multiplug from E box temperature sensor. 4.Remove E box temperature sensor.Refit 1.Fit E box temperature sensor to mounting. 2.Connect multiplug to E box temperature sensor. 3.Fit E box cover and tighten Allen screws to 2 Nm (1.5 lbf.ft). 4.Connect battery earth lead. 5.If a replacement sensor has been fitted, re-set adaptions using TestBook/T4. M18 0726
ENGINE MANAGEMENT SYSTEM - V8 REPAIRS 18-2-13 Housing - air cleaner $% 19.10.01 Remove 1.Remove air cleaner element. + ENGINE MANAGEMENT SYSTEM - V8, REPAIRS, Element - air cleaner. 2.Remove bolt securing air cleaner lower housing. 3.Release clip securing air intake pipe to lower air cleaner housing. 4.Remove lower air cleaner housing. NOTE: Do not carry out further dismantling if component is removed for access only. 5.Remove mountings from lower air cleaner housing. Refit 1.Fit mountings to lower air cleaner housing.2.Fit lower air cleaner housing, connect to air intake pipe and tighten securing bolt. NOTE: Make sure that the air intake pipe is located into the lugs of the lower air filter housing before the lower air filter housing is fully seated onto its mountings. 3.Fully seat air intake pipe securing clip to lower air cleaner housing. 4.Fit air cleaner element. + ENGINE MANAGEMENT SYSTEM - V8, REPAIRS, Element - air cleaner.
ENGINE MANAGEMENT SYSTEM - V8 18-2-14 REPAIRS Element - air cleaner $% 19.10.10 Remove 1.Release 2 clips securing MAF/IAT sensor to upper air cleaner housing. Disconnect SAI pump air intake hose from upper air cleaner housing. 2.Release 4 clips and remove upper air cleaner housing. 3.Discard O ring from upper air cleaner housing.4.Remove air cleaner element. Refit 1.Clean air cleaner housing. 2.Fit air cleaner element. 3.Fit O ring seal into upper air cleaner housing. 4.Lubricate O ring. 5.Fit upper air cleaner housing and secure clips. 6.Connect SAI pump hose to upper air cleaner housing.
ENGINE MANAGEMENT SYSTEM - V8 REPAIRS 18-2-15 Hose - air flow meter to throttle body $% 19.10.28 Remove 1.Remove engine acoustic cover. + Engine - V8, REPAIRS, Acoustic cover - engine. 2.Disconnect vacuum pipes from air intake pipe. 3.Release 2 clips and disconnect air intake pipe from throttle body. 4.Remove air intake pipe. 5.Remove seal from air intake pipe, at MAF sensor connection end. 6.Remove clips from air intake pipe.Refit 1.Fit seal to MAF sensor. 2.Lubricate air intake pipe mating face of throttle body seal and MAF sensor seal to aid refit. 3.Fit clips to air intake pipe. 4.Fit and secure air intake pipe. 5.Connect vacuum pipes to air intake pipe. 6.Fit engine acoustic cover. + Engine - V8, REPAIRS, Acoustic cover - engine. 7.If a replacement sensor has been fitted, reset adaptions using TestBook/T4.
ENGINE MANAGEMENT SYSTEM - V8 18-2-16 REPAIRS Sensor - accelerator pedal position (APP) $% 19.20.01 The APP sensor is not serviced separately from the throttle pedal. Before disconnecting the battery, ensure all text and cautions in the battery disconnection section are observed. + GENERAL INFORMATION, Electrical Precautions. Remove 1.Disconnect battery earth lead. 2.Remove cap from screw and remove Allen screw securing throttle pedal. 3.Release pedal from bracket, disconnect multiplug from APP sensor and remove pedal. Refit 1.Position throttle pedal and connect multiplug to APP sensor. 2.Fit pedal to bracket, tighten Allen screw to 10 Nm (7 lbf.ft) and fit cap to screw. 3.Connect battery earth lead. 4.If a replacement sensor has been fitted, re-set adaptions using TestBook/T4. Sensor - combined mass air flow (MAFS) & intake air temperature (IAT) $% 19.22.38 Before disconnecting the battery, ensure all text and cautions in the battery disconnection section are observed. + GENERAL INFORMATION, Electrical Precautions. Remove 1.Disconnect battery earth lead. 2.Remove air intake hose. + ENGINE MANAGEMENT SYSTEM - V8, REPAIRS, Hose - air flow meter to throttle body. 3.Disconnect multiplug from MAF/IAT sensor. 4.Release MAF/IAT sensor securing clips and remove sensor. NOTE: The O ring may become released from upper air cleaner housing during the removal of the MAF/IAT sensor. M86 5759
ENGINE MANAGEMENT SYSTEM - V8 REPAIRS 18-2-17 Refit 1.Fit O ring seal into upper air cleaner housing. 2.Lubricate O ring with clean engine oil. 3.Fit MAF/IAT sensor into upper air cleaner housing and secure with clips. 4.Connect multiplug to MAF/IAT sensor. 5.Connect air intake hose. + ENGINE MANAGEMENT SYSTEM - V8, REPAIRS, Hose - air flow meter to throttle body. 6.Connect battery earth lead. 7.If a replacement sensor has been fitted, re-set adaptions using TestBook/T4. Throttle body $% 19.22.45 Remove 1.Remove air intake hose. + ENGINE MANAGEMENT SYSTEM - V8, REPAIRS, Hose - air flow meter to throttle body. 2.Disconnect multiplug from throttle body. 3.Remove 4 bolts securing throttle body to inlet manifold and remove throttle body. 4.Discard 2 throttle body seals. M86 5710
ENGINE MANAGEMENT SYSTEM - V8 18-2-18 REPAIRS Refit 1.Clean mating faces of throttle housing and inlet manifold. 2.Fit 2 new throttle body seals. 3.Fit throttle housing to inlet manifold and tighten 4 bolts to 10 Nm (7 lbf.ft). 4.Connect multiplug to throttle body. 5.Connect air intake hose. + ENGINE MANAGEMENT SYSTEM - V8, REPAIRS, Hose - air flow meter to throttle body. 6.If fitting a new throttle body, reset adaptions using TestBook/T4. Fuel rail - remove for access & refit $% 19.60.04.99 Before disconnecting the battery, ensure all text and cautions in the battery disconnection section are observed. + GENERAL INFORMATION, Electrical Precautions. Remove 1.Disconnect battery earth lead. 2.Remove air intake hose. + ENGINE MANAGEMENT SYSTEM - V8, REPAIRS, Hose - air flow meter to throttle body. 3.Remove LH ignition coil cover. + ENGINE MANAGEMENT SYSTEM - V8, REPAIRS, Cover - Ignition coils - LH. 4.Remove RH ignition coil cover. + ENGINE MANAGEMENT SYSTEM - V8, REPAIRS, Cover - Ignition coils - RH. 5.Disconnect multiplugs from ignition coils. M86 5697
ENGINE MANAGEMENT SYSTEM - V8 REPAIRS 18-2-19 6.Disconnect multiplugs from throttle body, thermostat heater, CMP sensor and ECT sensor. 7.Cut 2 cable ties and release engine harness. 8.Disconnect multiplugs from VCC solenoids. 9.Release VCC multiplug harness from clip. 10.Disconnect multiplug from charcoal canister purge solenoid valve.11.Disconnect alternator multiplug. 12.Release alternator harness from 4 clips. 13.Disconnect multiplugs from KS and CMP sensor. 14.Remove 2 nuts securing fuel injector harness to fuel rail. 15.Release vacuum reservoir and mounting bracket from LH fuel injector harness securing stud. M86 5692 M86 5693 M86 5694 M86 5695 M86 5696