Home
>
Land Rover
>
Automobile
>
Land Rover Range Rover 2002my On Workshop Procedures Lm 6th Edition Nas Rover Manual
Land Rover Range Rover 2002my On Workshop Procedures Lm 6th Edition Nas Rover Manual
Have a look at the manual Land Rover Range Rover 2002my On Workshop Procedures Lm 6th Edition Nas Rover Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 364 Land Rover manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
SEATS 76-5-2 REPAIRS Front seat $% 78.10.44.99 Before disconnecting the battery, ensure all text and cautions in the battery disconnection section are observed. + GENERAL INFORMATION, Electrical Precautions. Remove 1.Raise seat cushion. 2.Remove bolt securing seat belt to front seat. 3.Remove nut caps and remove 2 nuts securing front of seat. 4.Move the seat forward. 5.Make the SRS system safe. + GENERAL INFORMATION, Supplementary Restraint System (SRS) Precautions. WARNING: Always disconnect both battery leads before beginning work on the SRS system. Disconnect the negative lead first. Never reverse connect the battery. 6.Release seat harness multiplug from bracket, release and disconnect main harness multiplug. 7.Remove 2 bolts securing rear of seat. 8.Fit protection to sill. 9.With assistance, carefully remove seat. Refit 1.Fit front seat. 2.Fit nuts and bolts securing seat and tighten to 45 Nm (33 lbf.ft). 3.Fit caps to nuts. 4.Fit seat belt to seat and tighten bolt to 48 Nm (35 lbf.ft). 5.Connect battery leads, earth lead last. 6.Reposition seat.
SEATS REPAIRS 76-5-3 Rear seat $% 78.10.48.99 Remove 1.Fit protection to wheel arch. 2.Remove 2 bolts securing rear seat. 3.Release rear seat and roll it forwards. 4.Disconnect multiplug from seat. 5.Remove 2 nuts securing seat and with assistance, carefully remove seat from vehicle. Refit 1.Fit rear seat in fully folded position and tighten nuts to 25 Nm (18 lbf.ft). 2.Connect multiplug to seat. 3.Position seat in upright position. 4.Fit bolts securing rear seat and tighten to 25 Nm (18 lbf.ft). Cover - one piece - front seat cushion $% 78.30.01 Remove 1.Remove seat assembly. + SEATS, REPAIRS, Front seat. 2.Remove Allen bolt securing arm rest. 3.Remove armrest from boss. 4.Remove screw securing finisher on inner seat base, remove finisher. 5.Remove switch pack assembly. + SEATS, REPAIRS, Switch pack - seat memory. 6.Release 3 backboard tension straps from under seat. M78 0606 M78 0613
SEATS 76-5-4 REPAIRS 7.Release staples securing squab cover to lower backboard. 8.Release squab side cover from both sides of backboard. 9.Release 2 studs securing lower half of backboard. 10.Release backboard from seat.11.Disconnect lumbar harness multiplugs from pump and valve. 12.Disconnect multiplug from heated seat circuit. 13.Release harness from retaining clip and feed through squab cover. 14.Remove 2 Torx bolts and remove squab frame from seat frame. M78 0616
SEATS REPAIRS 76-5-5 15.Release seat cover beading from rear of frame. 16.Release seat cover beading from sides and front of frame. 17.Remove seat cushion and cover assembly. 18.Remove 15 hog rings securing cover to cushion, remove cover. Refit 1.Position cover to cushion and secure with hog rings. 2.Position and secure cover and cushion assembly to frame. 3.Position squab frame to seat frame, fit Torx bolts tighten to 25 Nm (18 lbf.ft). 4.Route lumbar harness through squab cover and secure to frame. 5.Connect multiplug to heated seat circuit. 6.Connect lumbar harness multiplugs to pump and valve. 7.Position backboard to seat assembly, fit studs securing lower of backboard. 8.Position and fit both sides of squab cover to backboard. 9.Position lower squab cover to backboard and staple.10.Fit backboard tension straps to under seat retaining clips. 11.Fit switch pack assembly. + SEATS, REPAIRS, Switch pack - seat memory. 12.Position inner seat base finisher and secure with screw. 13.Fit armrest to boss and secure with Allen bolt, tighten to 25 Nm (18 lbf.ft). 14.Fit seat assembly. + SEATS, REPAIRS, Front seat.
SEATS 76-5-6 REPAIRS Cover - one piece - front seat cushion - models with adjustable upper squab $% 78.30.02 Remove 1.Remove seat assembly. + SEATS, REPAIRS, Front seat. 2.Remove switch pack assembly. + SEATS, REPAIRS, Switch pack - seat memory. 3.Remove screw securing finisher on inner seat base, remove finisher. 4.Release 3 backboard tension straps from under seat. 5.Remove 2 screws securing lower squab finisher. 6.Release lower finisher from 6 retaining clips and remove. 7.Disconnect 2 tension straps securing upper squab cover. 8.Release velcro strip securing squab cover. M78 0628
SEATS REPAIRS 76-5-7 9.Release beading from squab cover finisher. 10.Release finisher from 4 retaining clips and remove. 11.Carefully release 2 retaining clips securing headrest to motor housing. 12.Remove headrest. 13.Release retaining strip securing squab cover to lower frame.14.Disconnect multiplugs from headrest and upper squab motors. 15.Disconnect multiplugs from lumbar pump and valve. M78 0635
SEATS 76-5-8 REPAIRS 16.Disconnect multiplug from heated seat circuit. 17.Release 2 retaining strips, securing both sides of lower squab cover to frame. 18.Release squab harness from 4 retaining clips. 19.Remove 2 Torx bolts securing squab frame to seat frame. 20.Remove squab assembly from seat assembly. 21.Release seat cover beading from sides and front of frame. 22.Remove seat cover and pad from frame.23.Remove 15 hog rings securing cover to cushion, remove cover. Refit 1.Position cover to cushion and secure with hog rings. 2.Position and secure cover and cushion assembly to frame. 3.Position and fit squab assembly to seat assembly. 4.Fit squab frame to seat frame, secure with Torx bolts tighten to 25 Nm (18 lbf.ft). 5.Fit retaining strips securing both sides of lower squab cover. 6.Connect multiplug to heated seat circuit. 7.Secure squab harness to retaining clips 8.Connect lumbar harness multiplugs to pump and valve. 9.Connect multiplugs to headrest and squab motor. 10.Fit retaining strip securing lower squab cover to frame. 11.Fit headrest and secure to motor housing. 12.Position upper finisher and secure retaining clips. 13.Secure squab cover beading to finisher. 14.Secure squab cover velcro strip 15.Connect tension straps securing upper squab cover. 16.Position lower finisher and secure retaining clips 17.Fit screws securing lower squab finisher. 18.Fit backboard tension straps to under seat retaining clips. 19.Position inner seat base finisher and secure with screw. 20.Fit switch pack assembly. + SEATS, REPAIRS, Switch pack - seat memory. 21.Fit seat assembly. + SEATS, REPAIRS, Front seat. M78 0636
SEATS REPAIRS 76-5-9 Cover - rear seat cushion - RH $% 78.40.04 Remove 1.Remove seat base finisher. + SEATS, REPAIRS, Finisher - seat base rear. 2.Remove seat fold mechanism. + SEATS, REPAIRS, Hinge - rear seat - side. 3.Disconnect multiplug from squab harness. 4.Remove Torx bolt securing squab frame to seat frame, separate frames. 5.Release seat cover both sides and front beading, raise cover and cushion. 6.Release heated seat harness multiplug from retaining clip and feed harness through frame. 7.Release 1 stud and rear beading securing seat cover to frame, remove cover and cushion.8.Release 11 staples securing seat cover to cushion. 9.Remove 16 hog rings securing cover to cushion, remove cover. Refit 1.Position seat cover to cushion and secure with hog rings. 2. Fit 11 staples securing cover under cushion. 3.Position cushion to frame and secure rear of cover. 4.Fit stud securing rear cover. 5.Feed heated seat harness through seat frame and secure multiplug to retaining clip. 6.Fit seat cover sides and front beading. 7.Fit Torx bolt securing squab frame to seat frame, tighten to 45 Nm (33 lbf.ft). 8.Connect multiplug to squab harness. 9.Fit seat fold mechanism. + SEATS, REPAIRS, Hinge - rear seat - side. 10.Fit seat base finisher. + SEATS, REPAIRS, Finisher - seat base rear. M78 0642 M78 0643
SEATS 76-5-10 REPAIRS Cover - rear seat cushion - LH $% 78.40.05 Remove 1.Remove LH seat base finisher. + SEATS, REPAIRS, Finisher - seat base rear. 2.Remove seat fold mechanism. + SEATS, REPAIRS, Hinge - rear seat - side. 3.Disconnect multiplug from squab harness. 4.Remove Torx bolt securing squab frame to seat frame, separate frames. 5.Release seat cover both sides and front beading, raise cover and cushion. 6.Release heated seat harness multiplug from retaining clip and feed harness through frame.7.Remove and discard Torx bolt securing seat belt to seat base frame. 8.Release seat belt from seat cushion and cover. 9.Release stud and rear beading securing seat cover to frame, remove cover and cushion. 10.Release 11 staples securing seat cover to cushion. 11.Release 25 hog rings securing cover to cushion and remove cover. M78 0646
SEATS REPAIRS 76-5-11 Refit 1.Position seat cover to cushion and secure with hog rings. 2. Fit 14 staples securing cover under cushion. 3.Position cushion to frame and secure rear of cover. 4.Fit stud securing rear cover. 5.Feed heated seat harness through seat frame and secure multiplug to retaining clip. 6.Position seatbelt lower buckle to frame and secure with Torx bolt tighten to 31 Nm (23 lbf.ft). 7.Fit seat cover sides and front beading. 8.Fit Torx bolt securing squab frame to seat frame, tighten to 45 Nm (33 lbf.ft). 9.Connect multiplug to squab harness. 10.Fit seat fold mechanism. + SEATS, REPAIRS, Hinge - rear seat - side. 11.Fit seat base finisher. + SEATS, REPAIRS, Finisher - seat base rear. Finisher - rear seat squab $% 78.55.03 Remove 1.Fold rear seat forward. 2.Release 3 clips securing latch finisher, remove finisher. 3.Remove 2 screws securing lower squab finisher. 4.Release 3 retaining clips securing finisher and remove finisher.