Home
>
Land Rover
>
Automobile
>
Land Rover Range Rover 2002my On Workshop Procedures Lm 6th Edition Nas Rover Manual
Land Rover Range Rover 2002my On Workshop Procedures Lm 6th Edition Nas Rover Manual
Have a look at the manual Land Rover Range Rover 2002my On Workshop Procedures Lm 6th Edition Nas Rover Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 364 Land Rover manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
EMISSION CONTROL - V8 17-2-10 REPAIRS Sensor - heated oxygen (HO2S) - pre- catalyst $% 19.22.16 Remove 1.Raise vehicle on lift. 2.Release HO2S harness from clip. 3.Release HO2S multiplug from support bracket. 4.Disconnect HO2S multiplug from harness. 5.Remove HO2S. 6.Remove and discard HO2S sealing washer. Refit 1.Clean HO2S and front pipe mating face. 2.Fit new sealing washer and apply anti seize compound to thread of HO2S. Fit and tighten to 50 Nm (37 lbf.ft). CAUTION: Ensure anti-seize compound does not contact sensor tip. 3.Connect HO2S multiplug and secure to support bracket. 4.Secure harness in clip. Sensor - heated oxygen (HO2S) - post catalyst $% 19.22.71 Remove 1.Raise vehicle on lift. 2.Release HO2S harness from clips. 3.Release HO2S multiplug from support bracket. 4.Disconnect HO2S multiplug from harness. 5.Remove HO2S and discard sealing washer. Refit 1.Clean HO2S and front pipe mating face. 2.Fit new sealing washer and apply anti seize compound to thread of HO2S. Fit and tighten HO2S to 50 Nm (37 lbf.ft). CAUTION: Ensure anti-seize compound does not contact sensor tip. 3.Connect HO2S multiplug to sensor and secure to support bracket. 4.Secure harness in clips. M19 3365M19 3367
ENGINE MANAGEMENT SYSTEM - V8 REPAIRS 18-2-1 ENGIN E MANAGEMENT SY STEM - V8 REPAIRS Spark plugs $% 18.20.02 Before disconnecting the battery, ensure all text and cautions in the battery disconnection section are observed. + GENERAL INFORMATION, Electrical Precautions. Remove 1.Disconnect battery earth lead. 2.Remove ignition coils. + ENGINE MANAGEMENT SYSTEM - V8, REPAIRS, Ignition coils - multiple - set. 3.Clean area around spark plugs. 4.Remove 8 spark plugs. Refit 1.Fit 8 spark plugs and tighten to 31 Nm (23 lbf.ft). 2.Fit 8 ignition coils. + ENGINE MANAGEMENT SYSTEM - V8, REPAIRS, Ignition coils - multiple - set. 3.Connect battery earth lead. Relay - ignition coils $% 18.20.05 Before disconnecting the battery, ensure all text and cautions in the battery disconnection section are observed. + GENERAL INFORMATION, Electrical Precautions. Remove 1.Disconnect battery earth lead. 2.Remove 10 Allen screws securing E box cover and remove cover. 3.Release relay from E box and disconnect multiplug. Refit 1.Position relay, connect multiplug and fit relay to E box. 2.Fit E box cover and tighten Allen screws to 2 Nm (1.5 lbf.ft). 3.Connect battery earth lead. M18 0770
ENGINE MANAGEMENT SYSTEM - V8 18-2-2 REPAIRS Ignition coils - multiple - set $% 18.20.45 Before disconnecting the battery, ensure all text and cautions in the battery disconnection section are observed. + GENERAL INFORMATION, Electrical Precautions. Remove 1.Remove engine acoustic cover. + Engine - V8, REPAIRS, Acoustic cover - engine. 2.Remove LH ignition coil cover. + ENGINE MANAGEMENT SYSTEM - V8, REPAIRS, Cover - Ignition coils - LH. 3.Remove RH ignition coil cover. + ENGINE MANAGEMENT SYSTEM - V8, REPAIRS, Cover - Ignition coils - RH. 4.Remove 2 nuts and disconnect earth leads from camshaft covers. 5.Disconnect multiplugs from ignition coils. 6.Discard ignition coil cover gasket.7.Remove 14 ignition coil securing nuts. Remove 8 ignition coils. Refit 1.Fit 8 ignition coils. 2.Fit 14 nuts securing ignition coil and tighten to 4 Nm (3 lbf.ft). 3.Fit new ignition coil cover gasket. 4.Connect multiplugs to ignition coils. 5.Connect earth lead to camshaft cover and tighten nut to 4 Nm (3 lbf.ft). 6.Fit RH ignition coil cover. + ENGINE MANAGEMENT SYSTEM - V8, REPAIRS, Cover - Ignition coils - RH. 7.Fit LH ignition coil cover. + ENGINE MANAGEMENT SYSTEM - V8, REPAIRS, Cover - Ignition coils - LH. 8.Fit engine acoustic cover. + Engine - V8, REPAIRS, Acoustic cover - engine.M86 5761 M86 5697
ENGINE MANAGEMENT SYSTEM - V8 REPAIRS 18-2-3 Cover - Ignition coils - LH $% 18.20.52 Before disconnecting the battery, ensure all text and cautions in the battery disconnection section are observed. + GENERAL INFORMATION, Electrical Precautions. Remove 1.Disconnect battery earth lead. 2.Remove engine acoustic cover. + Engine - V8, REPAIRS, Acoustic cover - engine. 3.Remove 2 access covers from ignition coil cover. 4.Remove 2 bolts securing ignition coil cover to camshaft cover. 5.Remove LH ignition coil cover. 6.Remove 2 bolt spacers from ignition coil cover. NOTE: Do not carry out further dismantling if component is removed for access only. 7.Remove nut and disconnect earth lead from camshaft cover. 8.Disconnect multiplugs from ignition coils. 9.Discard ignition coil cover gasket. Refit 1.Fit new ignition coil cover gasket. 2.Connect multiplugs to ignition coils. 3.Connect earth lead to camshaft cover and tighten nut to 4 Nm (3 lbf.ft). 4.Fit 2 bolt spacers to ignition coil cover. 5.Fit ignition coil cover, fit and tighten 2 bolts. 6.Fit 2 access covers to ignition coil cover. 7.Fit engine acoustic cover. + Engine - V8, REPAIRS, Acoustic cover - engine. 8.Connect battery earth lead. M86 5761 M86 5697
ENGINE MANAGEMENT SYSTEM - V8 18-2-4 REPAIRS Cover - Ignition coils - RH $% 18.20.53 Before disconnecting the battery, ensure all text and cautions in the battery disconnection section are observed. + GENERAL INFORMATION, Electrical Precautions. Remove 1.Disconnect battery earth lead. 2.Remove engine acoustic cover. + Engine - V8, REPAIRS, Acoustic cover - engine. 3.Remove 2 access covers from ignition coil cover. 4.Remove 2 bolts securing ignition coil cover to camshaft cover. 5.Remove RH ignition coil cover. 6.Remove 2 bolt spacers from ignition coil cover. NOTE: Do not carry out further dismantling if component is removed for access only. 7.Remove nut and disconnect earth lead from camshaft cover.8.Disconnect multiplugs from ignition coils. 9.Discard ignition coil cover gasket. Refit 1.Fit new ignition coil cover gasket. 2.Connect multiplugs to ignition coils. 3.Connect earth lead to camshaft cover and tighten nut to 4 Nm (3 lbf.ft). 4.Fit 2 bolt spacers to ignition coil cover. 5.Fit ignition coil cover, fit and tighten 2 bolts. 6.Fit 2 access covers to ignition coil cover. 7.Fit engine acoustic cover. + Engine - V8, REPAIRS, Acoustic cover - engine. M86 5697
ENGINE MANAGEMENT SYSTEM - V8 REPAIRS 18-2-5 Engine control module (ECM) $% 18.30.03 If the ECM is to be replaced then Testbook/T4 must be connected and correct procedures adhered to, prior to battery disconnection. Before disconnecting the battery, ensure all text and cautions in the battery disconnection section are observed. + GENERAL INFORMATION, Electrical Precautions. Remove 1.Disconnect battery earth lead. 2.Remove 10 Allen screws securing E box cover and remove cover. 3.Disconnect 5 multiplugs from ECM. 4.Release 2 clips and remove ECM.Refit 1.Fit new ECM and connect multiplugs. 2.Fit E box cover and tighten Allen screws to 2 Nm (1.5 lbf.ft). 3.Connect battery earth lead. 4.Reprogramme a new ECM using TestBook/T4. M18 0742
ENGINE MANAGEMENT SYSTEM - V8 18-2-6 REPAIRS Relay - combined ignition & fuel ECU $% 18.30.06 Remove 1.Disconnect battery earth lead. 2.Remove 10 Allen screws securing E box cover and remove cover. 3.Disconnect and remove, ECM relay from E box multiplug. Refit 1.Position relay to E box mounting and connect multiplug. 2.Fit E box cover and tighten Allen screws to 2 Nm (1.5 lbf.ft). 3.Connect the battery earth lead. Sensor - engine coolant temperature (ECT) $% 18.30.10 Before disconnecting the battery, ensure all text and cautions in the battery disconnection section are observed. + GENERAL INFORMATION, Electrical Precautions. Remove 1.Disconnect battery earth lead. 2.Disconnect multiplug from ECT sensor. 3.Position container beneath ECT sensor to collect coolant. 4.Using a deep socket, carefully remove ECT sensor and discard seal. M18 0727A M18 0744
ENGINE MANAGEMENT SYSTEM - V8 REPAIRS 18-2-7 Refit 1.Ensure mating faces of ECT sensor and coolant pump are clean. 2.Fit new seal and tighten ECT sensor to 15 Nm (11 lbf.ft). 3.Connect multiplug to ECT sensor. 4.Remove container. 5.Dispose of coolant and clean container. 6.Connect battery earth lead. 7.Check and top up cooling system. + MAINTENANCE, PROCEDURES, Cooling system. 8.If a replacement sensor has been fitted re-set adaptions using TestBook/T4. Sensor - crankshaft position (CKP) $% 18.30.12 Before disconnecting the battery, ensure all text and cautions in the battery disconnection section are observed. + GENERAL INFORMATION, Electrical Precautions. Remove 1.Position vehicle on lift. 2.Disconnect battery earth lead. 3.Raise vehicle and disconnect multiplug from CKP sensor. 4.Clean area surrounding CKP sensor. 5.Remove Allen screw and remove CKP sensor. Refit 1.Clean casing mating face.
ENGINE MANAGEMENT SYSTEM - V8 18-2-8 REPAIRS 2. Observe the following when replacing the transmission, incremental gear or the CKP sensor. If one or more spacers are fitted between transmission and CKP sensor, the distance between the sensor and teeth on the incremental gear must be measured. 3.Rotate crankshaft until a full trigger tooth is visible through aperture in casing. Ensure the tooth is centred to the hole. 4.Using a depth micrometer, measure depth from sensor mating face to trigger tooth. Record measurement.5.Measure length of CKP sensor between tip and mounting face, dimension A. Record dimension. 6.Subtract length of CKP sensor, from sensor mating face to trigger tooth dimension and record the resulting gap. The Air gap should be adjusted to 0.55 mm +/- 0.2 (.022 in +/- .0080), using available shims. 7.Fit shim to CKP sensor if required. Align CKP sensor to casing, fit bolt and tighten to 10 Nm (7 lbf.ft). 8.Connect CKP sensor multiplug. 9.Connect battery earth lead. 10.If a replacement sensor has been fitted re-set adaptions using TestBook/T4. M18 0771 A
ENGINE MANAGEMENT SYSTEM - V8 REPAIRS 18-2-9 Sensor - camshaft position (CMP) - LH $% 18.30.25 Before disconnecting the battery, ensure all text and cautions in the battery disconnection section are observed. + GENERAL INFORMATION, Electrical Precautions. Remove 1.Disconnect battery earth lead. 2.Remove engine acoustic cover. + Engine - V8, REPAIRS, Acoustic cover - engine. 3.Disconnect multiplug from CMP sensor. 4.Release CMP sensor harness from clip on camshaft cover. 5.Remove bolt securing CMP sensor and remove sensor. Discard O ring.Refit 1.Clean CMP sensor and mating face. 2.Fit new O ring to CMP sensor. 3.Fit CMP sensor, fit bolt and tighten to 10 Nm (7 lbf.ft). 4.Connect multiplug to CMP sensor. 5.Secure CMP sensor harness to clip on camshaft cover. 6.Fit engine acoustic cover. + Engine - V8, REPAIRS, Acoustic cover - engine. 7.Connect battery earth lead. 8.If a replacement sensor has been fitted, re-set adaptions using TestBook/T4.