Home
>
Land Rover
>
Automobile
>
Land Rover Range Rover 2002my On Workshop Procedures Lm 6th Edition Nas Rover Manual
Land Rover Range Rover 2002my On Workshop Procedures Lm 6th Edition Nas Rover Manual
Have a look at the manual Land Rover Range Rover 2002my On Workshop Procedures Lm 6th Edition Nas Rover Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 364 Land Rover manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
RESTRAINT SYSTEMS 75-36 REPAIRS 15.Transport deployed airbag module to designated area for incineration. CAUTION: Do not re-use or salvage any parts of the SRS system. NOTE: Do not transport deployed SRS components in the vehicle passenger compartment. Airbag module - head - rear - deployment - in vehicle $% 76.74.44 These guidelines are written to aid authorised personnel to carry out the safe disposal of airbag modules. Deploy WARNING: It is imperative that before any work is undertaken on the SRS system, the appropriate information is read thoroughly. 1.Make the SRS system safe. + GENERAL INFORMATION, Supplementary Restraint System (SRS) Precautions. 2.Remove headlining. + INTERIOR FITTINGS, REPAIRS, Headlining. 3.Disconnect multiplug from airbag module. 4.Check condition of deployment tool LRT-86- 003 and associated fly leads. 5.Connect deployment tool fly lead LRT-86-003/ 08 to airbag.
RESTRAINT SYSTEMS REPAIRS 75-37 6.Connect deployment tool LRT-86-003 to deployment tool fly lead LRT-86-003/08. 7.Connect deployment tool LRT-86-003 to battery. WARNING: Ensure all personnel are at least 15 metres (50 feet) away from the airbag module. 8.Press deployment tool operating button to deploy airbag module. 9.Disconnect deployment tool from battery. WARNING: During deployment parts of the airbag module become hot enough to burn you. Wait 30 minutes after deployment before touching the airbag module. 10.Disconnect deployment tool fly lead from airbag. CAUTION: Do not re-use or salvage any parts of the SRS system. NOTE: Do not transport deployed SRS components in the vehicle passenger compartment. Airbag module - head - rear - deployment - off vehicle $% 76.74.45 These guidelines are written to aid authorised personnel to carry out the safe disposal of airbag modules. Deploy WARNING: It is imperative that before any work is undertaken on the SRS system, the appropriate information is read thoroughly. 1.Make the SRS system safe. + GENERAL INFORMATION, Supplementary Restraint System (SRS) Precautions. 2.Remove airbag module from vehicle. + RESTRAINT SYSTEMS, REPAIRS, Airbag module - head - rear. 3.Check condition of deployment tool LRT-86- 003 and associated fly leads.
RESTRAINT SYSTEMS 75-38 REPAIRS 4.Position LRT-86-007/02 in vice, ensuring that vice jaws grip tool above the bottom flange to prevent possibility of tool being forced upwards during detonation. Tighten vice. 5.Fit and secure 2 off LRT-86-007/05 to LRT-86- 007/02. 6.Fit and secure airbag to LRT-86-007/05.7.Connect deployment tool fly lead LRT-86-003/ 08 to airbag. 8.Connect deployment tool LRT-86-003 to deployment tool fly lead LRT-86-003/08. 9.Connect deployment tool LRT-86-003 to battery. WARNING: Ensure all personnel are at least 15 metres (50 feet) away from the airbag module. 10.Press deployment tool operating button to deploy airbag module. 11.Disconnect deployment tool from battery. WARNING: During deployment parts of the airbag module become hot enough to burn you. Wait 30 minutes after deployment before touching the airbag module. 12.Disconnect deployment tool fly lead from airbag. 13.Remove airbag module from holding tools and place in a sealed bag, ready for disposal. 14.Wipe down holding tools with a damp cloth and remove from vice. M76 4599 LRT-86-007/02 LRT-86-007/05
RESTRAINT SYSTEMS REPAIRS 75-39 15.Transport deployed airbag module to designated area for incineration. CAUTION: Do not re-use or salvage any parts of the SRS system. NOTE: Do not transport deployed SRS components in the vehicle passenger compartment.
DOORS ADJUSTMENTS 76-1-1 DOORS ADJUST ME NTS Tailgate lower - adjust on striker $% 76.28.03 Check 1.Check for equal gap and alignment to adjacent panels. If incorrect follow adjust procedure below. Adjust 1.Open tailgate. 2.Loosen 2 bolts securing lower tailgate striker. 3.Close tailgate, check for equal gap and alignment to adjacent panels. 4.Open lower tailgate and tighten bolts securing striker to 25 Nm (18 lbf.ft). 5.Close tailgate. Tailgate upper - adjust on striker(s) $% 76.28.28 Adjust 1.Open tailgate. 2.Remove trim finisher. + DOORS, REPAIRS, Finisher - upper - tailgate lower. 3.Using a Torx socket, loosen 2 striker screws and adjust striker. 4.Close tailgate, check for equal gap and alignment to adjacent panels. 5.Open tailgate and tighten striker Torx screws to 10 Nm (7 lbf.ft). 6.Adjust other striker if necessary. 7.Fit trim finisher. + DOORS, REPAIRS, Finisher - upper - tailgate lower. 8.Close tailgate. M76 4531
DOORS REPAIRS 76-1-3 REPAIRS Glass - front door $% 76.31.01 Remove 1.Lower door glass. 2.Remove plastic sheet. + DOORS, REPAIRS, Plastic sheet - front door. 3.Loosen two Torx bolts securing glass to regulator. 4.Remove glass. Refit 1.Position glass to regulator. 2.Lightly tighten Torx bolts. 3.Raise regulator, check glass alignment, adjust as necessary. 4.Tighten Torx bolts securing front glass to 10 Nm (7 lbf.ft). 5.Fit plastic sheet. + DOORS, REPAIRS, Plastic sheet - front door. Glass - rear door $% 76.31.02 Remove 1.Lower door glass. 2.Remove plastic sheet. + DOORS, REPAIRS, Plastic sheet - rear door. 3.Remove 2 clips securing upper door frame finisher, disconnect anti trap multiplug and remove finisher. 4.Remove 3 Torx screws securing rear glass channel to door frame. 5.Withdraw glass channel from frame and position channel seal aside. M76 4508
DOORS 76-1-4 REPAIRS 6.Remove Torx bolt securing glass to regulator. 7.Remove glass. Refit 1.Position glass to regulator, fit bolt and tighten to 10 Nm (7 lbf.ft). 2.Fit glass channel to frame and secure with screws. 3.Fit and secure seal. 4.Connect multiplug, fit and secure upper finisher. 5.Fit plastic sheet. + DOORS, REPAIRS, Plastic sheet - rear door. 6.Raise and lower glass to check operation. Quarter light - fixed - rear door $% 76.31.31 Remove 1.Remove rear door glass. + DOORS, REPAIRS, Glass - rear door. 2.Remove 3 screws securing rear finisher to frame and remove finisher. 3.Remove rear finisher retaining clips from door frame. 4.Remove top finisher from door. M76 4497 M76 4498
DOORS REPAIRS 76-1-5 5.Remove outer waist seal. 6.Remove inner waist seal. 7.Remove quarter light outer trim. 8.Use a Kent knife and carefully cut through sealant securing glass to door frame. 9.Remove quarter light. Refit 1.Carefully remove sealant from door frame to leave a smooth surface.2. Original quarter light: Carefully cut back sealant to obtain a smooth surface without damage to obscuration band. 3.Clean sealant face on door frame and quarter light with solvent. 4.Apply etch primer to any bare metal on door frame. 5.Apply primer over etch primer. 6.Fit pre-cut nozzle to sealer cartridge, remove lid, shake out crystals and fit cartridge to applicator gun. If necessary modify the nozzle to achieve required bead section. 7.Apply a continuous bead of sealant to door frame. Dimension A = 7 mm (0.28 in). Dimension B = 11 mm (0.44 in). 8.Fit and centralise quarter light to door frame. Lightly press quarter light to seat sealer. 9.Fit quarter light trim. 10.Fit inner waist seal to door. 11.Fit outer waist seal to door. 12.Fit door, top finisher. 13.Fit rear finisher retaining clips to door frame. 14.Fit and secure rear finisher to frame. 15.Fit rear door glass. + DOORS, REPAIRS, Glass - rear door. 16.Test sealer for leaks, apply additional sealer if necessary. If water is used, allow sealer to dry before testing. Spray water around glass and check for leaks. Mark any area that leaks. Dry glass and sealer then apply additional sealer. M76 4499 M76 4500 M76 4510