Lucent Technologies DEFINITY Enterprise Communications Server Release 8.2 Upgrades And Additions Manual

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Upgrading R5si/R6si to R8r EPN and Adding Memory 
3-9 Preliminary Procedures 
3
Check Software Release Letter
1. Check the Software Release Letter that ac c omp anies the Release 8 
removab le media. This letter c ontains the rec ommend ed  up g rade 
proc edures. Always use the 
Software Release Letter when up g rad ing  a 
system. 
2. If the letter is not inc lud ed  with the Release 8 removab le med ia, p erform 
the following procedures. 
Busyout Multimedia Interface Circuit Packs
Perform this step  only if the system is hig h or c ritic al reliab ility and  c ontains 
MMCH c irc uit p ac ks. Multimed ia-to-voic e station c alls are 
not p reserved  on an 
up g rad e. Failure to b usy-out the TN787 Multimed ia Interfac e c irc uit p ac ks will 
result in unusab le TN787 and  TN788 Multimed ia Voic e Cond itioner p orts.
1. Type display system-parameters customer-options
 and  p ress 
En t e r. If 
the MMCH op tion is set to y
, c ontinue to step  2. If not, skip  to ‘‘Save 
Translations and Announcements’’. 
2. Type list configuration all
 and  p ress 
En t e r. Loc ate all of the TN787 
Multimed ia Interfac e c irc uit p ac ks.
3. Type busyout board
  and press 
En t e r  for eac h TN787. This 
p revents any further multimed ia-to-voic e c onnec tions and  d rop s all ac tive 
c onnec tions.
Save Translations and Announcements
1. Log  in at the manag ement terminal on the Release 5/6 system.
2. If the system is d uplex, typ e status system
 and press 
En t e r  to verify the 
system is in the ‘‘ac tive/stand b y mode.
3. Type save translation
 and press 
En te r. This instruc ts the system to write all 
translation information from memory to the translation c ard s.
4. Chec k for translation errors before p roc eed ing  with the up g rad e. If errors 
are d etec ted , refer to ‘‘No Translations After Upgrade’’
 in Appendix B, 
‘‘Troubleshooting  an Upgrade’’ to c orrec t the p rob lem. Do not c ontinue 
until the errors are c orrec ted . 
5. If the system c ontains a TN750/B Announc ement c irc uit p ac k, type 
display announcements
 and  p ress 
En t e r.
6. If administered  rec ord ed  announc ements are listed , typ e save 
announcements
 and  p ress 
En te r.
7. Remove the translation c ard and  install the b ac kup  removab le media or 
card. 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Upgrading R5si/R6si to R8r EPN and Adding Memory 
3-10 Release 5/6si to Release 8r 
3
Release 5/6si to Release 8r
During  the wiring  of the PPN installation, lab el the MDF with the new PN numb er 
of the Release 5/6si PPN. The STS software up g rad e assigns the next PN numb er 
(after the hig hest numbered  PN in the Release 5/6si system) to the up g rad ed  
Release 8r EPN.
Required Tools
The following tools and  items may b e req uired  d uring  the up g rad e:
n1/4-inc h flat b lad e sc rewd river
n1/4-inc h soc ket with ratc het (op tional)
nLong -nose p liers to straig hten b ac kp lane p ins
nStatic -p roof or orig inal c irc uit p ac k p ac kag ing  for transp orting  c irc uit 
packs
nLab els for id entifying  the p ort c irc uit p ac ks and  c ab les attac hed  to the 
rear of c ab inets
nRep air kit for b ac kp lane p ins (KS-22876 L2 or eq uivalent)
nOne c op y of eac h of the following  manuals:
— DEFINITY Enterp rise Communic ations Server Release 8 
Maintenanc e for R8r
— DEFINITY Enterp rise Communic ations Server Release 8 
Ad ministrator’s Guid e 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Upgrading R5si/R6si to R8r EPN and Adding Memory 
3-11 Release 5/6si to Release 8r 
3
Required Hardware
The eq uip ment in Table 3-2 must be on-site before the upgrade begins.
Table 3-2. Required Hardware
Equipment Description Quantity
J58890N Expansion Control Cab inet 1
106647985 TN775B Maintenance circ uit p ac k  1
103281788 TN570 Exp ansion Interface circuit p ack Dep end s on reliab ility type 
and numb er of PNs
103281812 TN573B Switc hed  Nod e Interfac e c irc uit p ac k Dep end s on reliab ility type 
and numb er of PNs
407439975 or
40759832520-Foot Multi-Mod e Fib er Op tic  Cable
20-Foot Sing le-Mod e Fib er Op tic  Cable1 to 12
106455348 or
106455363 or
1077318539823-A Lig htwave Transc eiver
9823-B Lig htwave Transc eiver
300A Lig htwave Transceiver2 to 12
1
2 to 121
2 to 122
1. For eac h fib er connec tion, 1 lig htwave transc eiver is installed  in 1 p ort network, and  a like transceiver
in the adjacent p ort network. 4E transc eivers c annot b e reused. Add itional transceivers, ord ered
sep arately, ship  loose with the EPN eq uip ment.
2. The 300A is c onnec ted  using  2 fib er optic  c ables. 5, 10, or 15 dB attenuators may b e required . J58890to-O L1 Release 8 Removab le Med ia 2 or 4
3
3. Dep ending on the reliab ility type of the Release 8r system. Two removab le med ia are req uired for a
stand ard reliability system; 4 for a hig h or c ritic al reliab ility system. 106689516 TN771D Maintenance Test c irc uit p ac k 1 or 2
4
4. Dep ending on the numb er of EPNs in a critic al reliab ility Release 8r system.846307817 Lower Rear Cover 1
5
5.Req uired  for the ‘‘B port cab inet of a c ritical reliab ility Release 8r EPN.  846307809 Ground Plate 1
H600-248 G1 ICC Cab les 2
6
6. Req uired  for a c ritic al reliab ility Release 8r EPN.
846408268 Earthq uake Front Panel (earthquake p rotec tion only) 1
846408386 Earthq uake Ground  Plate (earthq uake p rotection only) 1 
846408250 Stiffener (earthquake protec tion only) 1 
846408243 Earthq uake Front Mounting  Ang le (earthq uake 
p rotec tion only)1 
106060718 5 d B attenuator (sing le-mod e fib er only) 2 for each fib er c onnec tion
2
106060734 10 dB attenuator (sing le-mod e fiber only) 2 for each fib er c onnec tion2
106061021 15 dB attenuator (sing le-mod e fiber only) 2 for each fib er c onnec tion2 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Upgrading R5si/R6si to R8r EPN and Adding Memory 
3-12 Release 5/6si to Release 8r 
3
Follow Routine Preventive Maintenance
1. During  the up g rad e, follow routine p reventive maintenanc e p roc ed ures on 
the system to b e up g rad ed . For more information, refer to the “ Preventive 
Maintenanc e”  sec tion in 
DEFINITY Enterp rise Communic ations Server 
Release 8 Maintenanc e for R8r
.
Label Cables
1. To make rec onnec ting  the c ab les simp ler and  more reliable, lab el every 
c onnec tor c ab le assoc iated  with the system.
Check Link Status
1. Type display communication-interface links
 and  p ress En t e r. 
2. Make note of all enab led links.
3. Type status link
   and  p ress 
En t e r.
4. Chec k the following  items and  note whic h links are in-servic e. You will 
need  this information after the up g rad e.
nPPP li n k s
nAud ix links
nISDN
nBX25
nEthernet
5. Repeat steps 3 and 4 for each enabled link.
Disable TTI
!CAUTION:
If you d o not d isab le the TTI, the translations c an b e c orrup ted .
1. Make sure the ISDN is in servic e. If not, attempt to b usy out and release 
the ISDN D-c hannel/link. This will b ring  the ISDN trunks b ac k into servic e.
2. Type change system-parameters features
 and press 
En t e r. 
3. On the sec ond  sc reen, set the Enabled?
 field  to n
 to d e-ac tivate the TTI 
feature. 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Upgrading R5si/R6si to R8r EPN and Adding Memory 
3-13 Release 5/6si to Release 8r 
3
Shut Down DEFINITY LAN Gateway System
!WARNING:
Neg lec ting  to shut d own a DEFINITY LAN Gateway assemb ly b efore 
p owering  d own the system c ab inet c an d amage the LAN Gateway d isk.
1. Log  onto the DEFINITY LAN Gateway. See the DEFINITY Communic ations 
System Generic  3 Installation, Ad ministration and  Maintenanc e of 
CallVisor ASAI over the DEFINITY LAN Gateway
 for the p roc ed ure to log  
on.
2. When the main menu ap p ears, selec t 
Maintenanc e.
3. Select 
Reset System from the Maintenanc e menu.
4. Select 
Sh u t d o w n from the Res et Sy ste m menu.
5. Unseat the LAN Gateway assemb ly from its b ac kp lane c onnec tors.
Shut Down DEFINITY AUDIX System
1. If a DEFINITY AUDIX System resid es in the system to b e up g rad ed , shut 
d own the AUDIX assemb ly and  allow the d isk to c omp letely sp in d own. 
Refer to the ‘‘DEFINITY AUDIX Power Procedures’’
 at the end  of this 
chapter.
!WARNING:
Neg lec ting  to shut d own an AUDIX assembly b efore p owering  d own 
the system c ab inet where it resides c an damag e the AUDIX d isk.
2. Unseat the AUDIX assemb ly from its b ac kp lane c onnec tors.
Power Down Existing System
1. At eac h PPN c ab inet p ower supp ly, set the main c irc uit b reaker to OFF.
!CAUTION:
Powering  d own the PPN will c ause imp ortant system d ata, suc h as 
BCMS d ata, rec ord s of queued  ACD c alls, Automatic  Wakeup  
req uests, and  Do Not Disturb  req uests to b e lost. Refer to DEFINITY 
Enterp rise Communic ations Server Release 8 Maintenanc e for R8r, 
for information ab out p rep aring  the system for a p ower d own.
2. At eac h EPN c ab inet p ower supp ly, set the main c irc uit b reaker to OFF. 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Upgrading R5si/R6si to R8r EPN and Adding Memory 
3-14 Release 5/6si to Release 8r 
3
Disconnect Power and Ground
1. Disc onnec t the c ab inet p ower c ord s from the rear of eac h c ab inet.
2. Disconnect the 10 AWG (#25) (2.6 mm
2) c oup led b ond ing  c ond uc tor wire.
3. Disc onnec t the 6 AWG (#40) (4.1 mm
2) c ab inet g round  wire from the 
g round  b ar in the c ab inet.
Install Emergency Transfer Ground Wire
!CAUTION:
To avoid  c ontaminating  single-p oint g round , do not c onnec t the g round  
strap  while the system is p owered  up .
1. Connect a 10 AWG (#25) (2.6 mm2) wire either to pin 49 of the c onnec ting  
b loc k or to p in 49 of the CAP (c ab le ac c ess p anel) assoc iated  with the 
emergenc y transfer p anel.
2. Route the other end  of the wire to an ap p roved  g round  and  c onnec t.
Disconnect Equipment and Cables
1. Disc onnec t all of the c onnec tor c ab les attac hing  to the PPN.
2. Disc onnec t the PC from the TERM c onnec tor.
3. Remove the g round  p late(s) from b etween all of the PPN c ab inets.
4. Remove the top  and bottom rear c overs from all of the PPN c ab inets.
Remove Circuit Packs
1. Lab el eac h p ort c irc uit p ac k in the c ontrol c ab inet with its slot numb er.
2. Remove all c irc uit p ac ks and  p ower units from the c ontrol c ab inet. Store 
the c irc uit p ac ks in the static -p roof p ac kag ing .
NOTE:
If a TN756 tone-d etec tor/g enerator was removed  from the Release 
5/6si, a new Release 8r tone c loc k (TN2182B) rep lac es this c irc uit 
p ac k. The TN2182B Tone-Cloc k rep lac es the tone d etec tor c irc uits 
on the TN756. A TN2182B eliminates the need for a TN748B. 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Upgrading R5si/R6si to R8r EPN and Adding Memory 
3-15 Release 5/6si to Release 8r 
3
Disconnect TDM/LAN Cables and ICC Cables
1. Remove and  retain all of the TDM/LAN c ab les. 
2. If the Release 5/6si system is stand ard  reliab ility, remove and  retain the 
ICC c ab les.
3. If the Release 5/6si system is duplicated, remove the ICC cables. They are 
rep lac ed  with new ICC c ab les (H600-248 G1).
Remove the Existing Control Cabinet
Sinc e the c ontrol c ab inet is at the b ottom of the p ort network, d ismantle the 
c ab inet stac k. Disc onnec t all the p ower, ground , TDM, ICC, and  c onnec tor 
cables.
1. Remove the c ab inet c lip b etween eac h c ab inet or front earthq uake p late 
as p rovid ed .
2. Remove the rear g round  p late.
3. Remove the p ort c ab inets from the stac k.
!CAUTION:
A p ort c ab inet may weigh as muc h as 125 p ounds. Use lifting  
p rec autions. 
4.If the system is d up lic ated , remove the c ontrol c ab inet in p osition ‘‘B. It is 
not reused.
5. If the b asic  c ontrol c ab inet in p osition ‘‘A is earthq uake mounted , remove 
and  retain the hard ware sec uring  the c ab inet to the floor.
6. Remove the b asic  c ontrol c ab inet. It is not reused .
Unpack and Install Expansion Control Cabinet
1. Unp ac k and  insp ec t the J58890N Exp ansion Control Cab inet. 
2. Position the exp ansion c ontrol c ab inet at the desired  loc ation.
3. Reinstall the earthq uake mounting  hard ware, if req uired.
Install Port Cabinets
1. Rep lac e the p ort c ab inets into their p rop er p ositions. 
NOTE:
For a dup lic ated  Release 5/6si, the J58890M Control Cabinet c an b e 
rep lac ed  b y a J58890H Port Cab inet in p osition ‘‘B. 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Upgrading R5si/R6si to R8r EPN and Adding Memory 
3-16 Release 5/6si to Release 8r 
3
Install Circuit Packs
1.Rep lac e the c irc uit p ac ks and  power supp lies in p ort c ab inets “ C”  and  “ D”  
if they were p reviously removed .
2. Using  the lab el on the front of the c arrier and  the annotated  “ list 
c onfig uration all”  (provid ed  with the Release 8r removab le med ia), install 
the c ontrol c irc uit p ac ks into the new exp ansion c ontrol c ab inet.
3. Install the p ort c irc uit p ac ks into the “ A”  c ab inet using  the lab el on the front 
of the c arrier and  the annotated  “ list c onfig uration all”  as a g uide.
NOTE:
Sinc e the new Release 8r exp ansion c ontrol c arrier has 6 more p ort 
slots than the removed  c ontrol c arrier, there should  b e no need  to 
retranslate these c irc uit pac ks.
4. For an EPN in a c ritic al reliab ility system, install a TN2182B Tone-Cloc k 
and  a TN570 EI in slots “ 1”  and  “ 2”  of p ort c ab inet “ B.”  See Table 3-3
.
’
Change Cabinet Address Plugs
If a d up lic ated  c ontrol c ab inet was removed from p osition “ B”  and  was not 
rep lac ed  with a new p ort c ab inet, the up g rad ed  EPN’s p ort c ab inets oc c up y 
d ifferent p ositions in the c ab inet stac k. 
1. Behind  eac h p ort c abinet, find  the ad d ress p lug  attac hed  to 2 of the 6 
b ac kp lane p ins to the rig ht of the p in-field b loc k for slot “ 00.”
2. Chang e the loc ation of eac h p ort c ab inet ad d ress p lug  to reflec t the 
c ab inet’s c urrent p osition. See Figure 3-1
.
Table 3-3. TN570 Expansion Interface Requirements
Cabinet2 PNs w/o Critical 
Reliability2 PNs w/Critical 
Reliability3 PNs w/o Critical 
Reliability3 PNs w/Critical 
Reliability
PPN 1 2 2 4
EPN  1 1 2 2 4
EPN  2 N / A N / A 2 4 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Upgrading R5si/R6si to R8r EPN and Adding Memory 
3-17 Release 5/6si to Release 8r 
3
Figure 3-1. Cabinet Address Plug Location Figure Notes
1. Ad dress Plug  (Shown Set to Carrier D)
2. Carrier B Jump er Loc ation (Default)
3. Carrier C Jumper Location
4. Rig ht Edg e of Bac kp lane5. Rig ht Ed g e of Cabinet
6. Bac kp lane Slot 00
7. To Connec tor Panel 
3
45
1
6
2
7
add_plug CJL 050906 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Upgrading R5si/R6si to R8r EPN and Adding Memory 
3-18 Release 5/6si to Release 8r 
3
Install TDM/LAN Bus Terminators
1. If the Release 5/6si PPN has only 1 c ab inet, install the 2 AHF110 TDM/LAN 
b us terminators p er Figure 3-2
.
Figure 3-2. TDM/LAN Bus Terminators for Single-Carrier Cabinet EPN
2. If the Release 5/6si PPN has more than 1 c abinet:
a. Install the AHF110 TDM/LAN b us terminator in Slot 03 on the rig ht 
sid e of the exp ansion c ontrol c ab inet as shown in Figure 3-3
.
b . Install the AHF110 TDM/LAN bus terminator on the top  p ort c ab inet, 
at the end  of the daisy c hain of the b us. Figure Notes
1.Control Cab inet (“ A”  Position)
2. AHF110 TDM LAN/Bus Terminator 
(Slot 18)3. AHF110 TDM LAN/Bus Terminator 
(Slot 01)