Lucent Technologies DEFINITY Enterprise Communications Server Release 8.2 Upgrades And Additions Manual

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Multicarrier G2 Universal Module to R8r EPN 
5-103 Critical Reliability 
5
Figure 5-33. Fiber Optic Connections PPN to EPN1 Figure Notes
1. Lightwave Transc eiver
2. To PPN Carrier A Slot 1A01
3 . To  EPN 1  C a r r ie r A Sl o t  2 A0 1
4. To PPN Carrier B Slot 1B01
5 . To  EPN 1  C a r r ie r B Sl o t  2 B0 26. Fiber Optic Cable
7. Op tic al Cross-Connec t Fac ility
8. 100A Lig htg uid e Interc onnec t Unit
9. TX Connec tor
10. RX Connec tor 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Multicarrier G2 Universal Module to R8r EPN 
5-104 Critical Reliability 
5
Figure 5-34. Fiber Optic Connections PPN to EPN2 Figure Notes
1. Lightwave Transc eiver
2. To PPN Carrier A Slot 1A02
3 . To  EPN 2  C a r r ie r A Sl o t  3 A0 1
4. To PPN Carrier B Slot 1B02
5 . To  EPN 2  C a r r ie r B Sl o t  3 B0 26. Fiber Optic Cable
7. Op tic al Cross-Connec t Fac ility
8. 100A Lig htg uid e Interc onnec t Unit
9. TX Connec tor
10. RX Connec tor 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Multicarrier G2 Universal Module to R8r EPN 
5-105 Critical Reliability 
5
Figure 5-35. Fiber Optic Connections EPN1 to EPN2
Verify Usable Circuit Pack Vintages
Verify that eac h c irc uit pac k reused  in the up g rad e c onforms to the usab le 
vintag e requirements for a DEFINITY ECS Release 8 system (see Referenc e 
Guide for Circuit Pack Vintages and Change Notices).Figure Notes
1. Lightwave Transc eiver
2. To PPN Carrier A Slot 1A02
3 . To  EPN 2  C a r r ie r A Sl o t  3 A0 1
4. To PPN Carrier B Slot 1B02
5 . To  EPN 2  C a r r ie r B Sl o t  3 B0 26. Fiber Optic Cable
7. Op tic al Cross-Connec t Fac ility
8. 100A Lig htg uid e Interc onnec t Unit
9. TX Connec tor
10. RX Connec tor 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Multicarrier G2 Universal Module to R8r EPN 
5-106 Critical Reliability 
5
Remove Power-Failure Ground Strap
Remove the g round  strap  from the power-failure transfer unit.
Boot the Release 8 System
1. Connect the management terminal to the “ TERMINAL”  c onnec tor b ehind  
PPN c ontrol c arrier “ A,”  or install the G3-MA ac c ord ing  to the “ Set Up  
G3-MA” chap ter of 
DEFINITY Communic ations System Generic  3 
Management Applications 
— Operations, 585-229-202.
2. Insert the translation c ard s in the TN794 fac ep lates.
3. At eac h EPN p ower d istrib ution unit, set the main c irc uit breaker to ON.
4. At the PPN p ower d istribution unit, set the main c irc uit b reaker to ON.
5. The system performs the reset level 4 rebooting proc ess, loading the 
d efault system translations from the translation c ard s. This takes 8 to 11 
minutes.
6. Get the ord er numb er of the up g rad e and  c all the reg ional CSA to req uest 
an “ init”  log in so the rig ht-to-use op tions c an b e enab led .
7. To use Ac cess Security Gateway (ASG), see Appendix C, ‘‘Access 
Security Gateway’’. 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Multicarrier G2 Universal Module to R8r EPN 
5-107 Critical Reliability 
5
Set Daylight Savings Rules
You c an set up  to 15 c ustomized  d aylig ht saving s time rules. If you have c ab inets 
in several different time zones, you c an set up  rules for eac h on a loc ation b asis. 
A d aylig ht saving s time rule sp ec ifies the exac t time when you want to transition 
to and  from d aylig ht saving s time. It also sp ec ifies the inc rement at whic h to 
transition. 
NOTE:
The d efault d aylig ht saving s rule is 0
, no d aylig ht saving s.
1. Type change daylight-savings-rules
 and press 
En t e r.
2. Type the appropriate start and stop information in the Change Day
, 
Month
, Date
, Time
, and  Increment
 field s for eac h rule. (for examp le, 
1:00
 eq uals one hour) 
NOTE:
You c an c hang e any rule exc ep t rule 0 (zero). You c annot delete a 
d aylig ht saving s rule if it is in use on either the Loc ations or Date and 
Ti m e  s c re e n s .
3. When d one, p ress 
En te r.
 
DAYLIGHT SAVINGS RULES
Rule Change Day Month___Date Time____Increment
0: No Daylight Savings
1: Start: first Sunday
___ on or after April ___  1 at _2:0001:00Stop:  first Sunday___ on or after October _ 25 at _2:002: Start: first _________ on or after _________ __ at __:__
Stop:  first _________ on or after _________ __ at __:__
3: Start: first _________ on or after _________ __ at __:__
Stop:  first _________ on or after _________ __ at __:__
4: Start: first _________ on or after _________ __ at __:__
Stop:  first _________ on or after _________ __ at __:__
5: Start: first _________ on or after _________ __ at __:__
Stop:  first _________ on or after _________ __ at __:__
6: Start: first _________ on or after _________ __ at __:__
Stop:  first _________ on or after _________ __ at __:__
7: Start: first _________ on or after _________ __ at __:__
Stop:  first _________ on or after _________ __ at __:__ 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Multicarrier G2 Universal Module to R8r EPN 
5-108 Critical Reliability 
5
Set Date and Time
1. Type set time 
and 
press En t e r to b ring  up  the Date and  Time sc reen.
Screen 5-3. Typical Date and Time Screen
2. Typ e the d ay of the week in Eng lish (Sunday throug h Saturd ay). See 
Tab le 5-17
 for English day of the week names.
Table 5-17. English Day of the Week Names
Day Number Day Name
1Sunday
2 Mond ay
3Tuesday
4 Wed nesd ay
5Thursday
6Friday
7Saturday
 
                           DATE AND TIME
DATE
 Day of the Week: Tuesday
Month: FebruaryDay of the Month: 8 Year: 2000
TIME
Hour: 20 Minute: 30Second: XX Type: standardDaylight Savings Rule: 0 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Multicarrier G2 Universal Module to R8r EPN 
5-109 Critical Reliability 
5
3. The c ursor is p ositioned  on the Month:
 field . Typ e the c urrent month in 
Eng lish (January throug h Dec emb er). See Table 5-18
 for Eng lish month 
names. After the month is entered, p ress 
Ta b to move to next field .
4. The c ursor is p ositioned  on the Day of the Month:
 field . Typ e the d ay 
of month (1 through 31) and  p ress 
Ta b to move to the next field.
5. The c ursor is p ositioned  on the Year:
 field . Typ e the c urrent year and  
p ress 
TA B to move to the next field .
6. The c ursor is p ositioned  on the Hour:
 field . Typ e the c urrent hour for a 
24-hour c loc k. Press
 Ta b to move to the next field .
7. The c ursor is p ositioned  on the Minute:
 field . Type c urrent minute (0 
throug h 59). Sec ond s c annot b e set.
8. Type standard
 or daylight savings
 in the Type
 field .
9. Typ e the rule (numb er) in the Daylight Savings Rule
 field.
10. Press 
En t e r when the information is c orrec t.
11. Typ e display time 
and press 
En te r  to verify d ate/time d ata.
Table 5-18. English Month Names
Month Number Month Name
1 January
2February
3March
4April
5May
6June
7July
8August
9 Sep temb er
10 Oc tob er
11 November
12 Dec emb er 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Multicarrier G2 Universal Module to R8r EPN 
5-110 Critical Reliability 
5
Set Additional Administration
1. Type list configuration software-version long
 and  p ress En te r  to 
c omp are the version numb er of the Release 8 software p rog ram 
(displayed  on the terminal) with the version numb er (written on a label on 
the p roc essor’s fac ep late). If the version numb ers are not the same, 
c hang e the version numb er on the p roc essor lab el so that they ag ree.
2. Type change system-parameters customer-options
 and press 
En te r. 
Use this sc reen to enable the G3 V6 op tion and  to assig n the c ustomer’s 
other rig ht-to-use op tions on the Release 8 upg rad e ord er. See 
DEFINITY 
Enterp rise Communic ations Server Release 8 Ad ministrator’s Guid e
, for 
d etails on enab ling  these op tions.
3. Type change site-data
 and press 
En te r. Use this sc reen to assig n 
system-sp ec ific  information (suc h as b uild ing , floor, stations, and so 
forth).
4. Type status system 1
 and press 
En t e r  to verify that the system is in the 
“active/standby” mode.
5. Type save translation
 and press 
En te r. This instruc ts the system to write all 
translation information from memory to the translation c ard s.
!WARNING:
If the terminal sc reen d isp lays “ translation c orrup tion d etec ted ; c all 
Luc ent Tec hnolog ies distrib utor immed iately” , an error was d etec ted  
in the translations. Call your Luc ent Tec hnolog ies rep resentative.
Close Upgraded EPN Cabinet and Reconnect
Cables
1. At the up g rad ed  EPN, set the main c irc uit b reaker to OFF.
NOTE:
Powering  d own an EPN without p owering  d own the PPN will set off 
alarms. However, these alarms should  c lear after p ower is restored  
to eac h EPN.
2. Temporarily d isc onnec t the lig htwave transc eivers and  fib er op tic  c ab les 
from the ap p ropriate c arriers.
3. Rep lac e the b ac k d oors or bac k p anels p reviously removed .
4. At the EPN c ab inet, rec onnec t the lig htwave transc eivers, fib er op tic  
c ab les, and  the c onnec tor c ab les assoc iated  with the c arrier b eing  
rep lac ed .
5. Install the front d oor on the EPN c abinet. 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Multicarrier G2 Universal Module to R8r EPN 
5-111 Critical Reliability 
5
Power Up the EPN Cabinets
1. At eac h EPN p ower d istrib ution unit, set the main c irc uit breaker to ON. 
After ab out 40 sec ond s, EPN power and  PPN/EPN c ommunic ations return.
2. After p ower returns to eac h EPN and  all troub le is c leared , verify that the 
EMERGENCY TRANSFER CONTROL switc h is set to AUTO. This restores 
the system to the normal mod e.
Retranslate Port Circuits
If p ort c irc uit p ac ks were reloc ated  in order to p ut:
nA c ritic al p ort c irc uit p ac k, requiring  long er nominal battery hold over (suc h 
as a DS1 or an Announc ement c irc uit p ac k), in a p ort slot
nA TN736, TN752, or TN755 power sup p ly in p ort slots “ 18”  and  “ 19”
nA TN776 or TN570 Exp ansion Interfac e in p ort slot “ 1”
nA TN776 or TN570 in p ort slot “ 2”  (for a sec ond  d irec tly c onnec ted  EPN)
of the new exp ansion c ontrol c arrier, verify that they were retranslated  d uring  the 
off-site software up g rad e. If not, they must b e retranslated now. Refer to 
DEFINITY Enterp rise Communic ations Server Release 8 Ad ministrator’s Guid e.
Enable TTI
1. Type change system-parameters features
 and press En t e r.
2. On the sec ond  sc reen, set the Enabled?
 field  to y
 to ac tivate the TTI 
feature.
Check Link Status
1. Type display communication-interface links
 and press En te r. Compare it 
with the earlier status.
2. Type status link
 
number and  p ress En t e r. Rep eat this step  for eac h link.
Enable Scheduled Maintenance
Ty p e  change system-parameters maintenance
 and press En t e r. Enab le the 
sc hed uled  d aily maintenanc e. 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Multicarrier G2 Universal Module to R8r EPN 
5-112 Critical Reliability 
5
Resolve Alarms
Examine the alarm log . Resolve any alarms that may exist using  DEFINITY 
Enterp rise Communic ations Server Release 8 Maintenanc e for R8si or DEFINITY 
Enterp rise Communic ations Server Release 8 Maintenanc e for R8r
. 
Enable Customer Options and Alarm Origination
1. Get the DOSS order number of the upgrade from the project manager and 
ask the reg ional Customer Software Ad ministration to c omp lete the step s 
in the shad ed  b ox. See ‘‘Where to Call for Tec hnic al Sup p ort’’ on p ag e -xx
 
for telep hone numb ers.
NOTE:
As p art of the system reg istration p roc ess, the INADS Datab ase 
Ad ministrator enab les Alarm Orig ination.
2. When ad ministration is c omp leted , log  in as craft
 at the Login:
 prompt.
init login administration:
1. Log in as init
.
2. Type change system-parameters customer-options
 and press 
En te r 
to verify that the c ustomer op tions are p roperly set.
3. Go to sc reen 6, QSIG Op tional Features, and  set the Basic Call 
Setup 
field  to y
 if the customer was using Supplementary Services 
Protoc ol b  or d  on an ISDN-PRI trunk g roup  b efore the up g rad e.
4. Type change system-parameters offer-options
 and  p ress 
En te r.
5. If the Activate Offer
 field  is n
, set it to y 
and press 
Ta b. A warning  
messag e lets you know whether you need  to save translations and  
reb oot to make the c hang e p ermanent.
6. Press 
En t e r to effec t the c hang es or Canc el if there were no c hang es.
7. Contac t the req uester when d one.