Lucent Technologies DEFINITY Enterprise Communications Server Release 8.2 Upgrades And Additions Manual

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Adding or Removing Cabinet Hardware 
6-19 Add the Fiber Optic Cable 
6
Figure 6-10. Replace the Fan Cover
13. Connec t the fib er c ab le to the ang led  c onnec tor on the front of the c irc uit 
pack. See Figure 6-11
.
lcda5fop EWS 110398
ENTER
/YES ENTER
/YES NEXT
/NO NEXT
/
NO BACK
BACK
AUDIX
AUDIXBOOT/
SHUTDOWN BOOT/
SHUTDOWN
ALARMS
EMER TR EMERTR 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Adding or Removing Cabinet Hardware 
6-20 Add the Fiber Optic Cable 
6
Figure 6-11. Connect Fiber Cable to Circuit Pack
14. Dress the cable using the supplied cable ties and cable tie mounts. See 
Figure 6-12
.
NOTE:
Dress the fiber optic  c able straight down the front of the circuit pack. 
Do not allow the c ab le to c ross in front of another c irc uit p ac k.
scdafo_4 KLC 051298
C12 456789101112131415161718TONE -
CL O CKPOWER UNIT EXPN
INTFC3EX PN
INTFC 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Adding or Removing Cabinet Hardware 
6-21 Add the Fiber Optic Cable 
6
Figure 6-12. Dress the Cable
15. If a c irc uit p ac k was removed  to ac c ess 2 op en slots (from ‘‘Cabinet 
Preparation’’ on page 6-10), rep lac e the c irc uit p ac k into its orig inal slot.
16. Close the front d oor.
17. Discard the pass-thru tool.
Test the Installation
1. Log in to the manag ement terminal.
2. Ad minister the system b y referring  to the ATM sec tion of the 
Installation 
and  Test for Ad junc ts and  Perip herals
.
3. Type list configuration all
 and  p ress 
En t e r to determine if the new c irc uit 
p ac k ap p ears in the c orrec t slot and  that there are no c irc uit p ac k 
conflicts.
lcda4fop RPY 021398 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Adding or Removing Cabinet Hardware 
6-22 Install a New EPN Cabinet in an Existing System 
6
Install a New EPN Cabinet in an 
Existing System
Figure 6-13 shows a typ ic al multic arrier EPN c ab inet. Eac h EPN c ab inet is 
normally p ositioned  ad jac ent to the PPN c abinet b ut may b e loc ated  remotely in 
a d ifferent room or a d ifferent b uild ing .
Figure 6-13. Typical Multicarrier EPN Cabinet 
1. Unc rate and  p osition the c ab inet as instruc ted  at the beg inning of this 
chapter.
2. Install earthq uake p rotec tion as instruc ted on p ag e 1-9.
32
Port Carrier C
Port Carrier B
Control Carrier A
Po r t Ca r r ie r D 
Port Carrier EFa ns
Power Distribution
0075_0 RBP 080196 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Adding or Removing Cabinet Hardware 
6-23 Install a New EPN Cabinet in an Existing System 
6
Connect Power and Ground 
1. For an AC- or DC-p owered  system, c onnec t p ower and ground  to the 
c ab inet as instruc ted  in 
DEFINITY Enterp rise Communic ations Server 
Release 8 Installation and  Test for Multic arrier Cab inets
.
2. Connec t the ap p roved  g round  to the new c abinet as instruc ted  in 
DEFINITY Enterp rise Communic ations Server Release 8 Installation and  
Test for Multic arrier Cabinets.
NOTE:
Do not p ower up  the system until all p ower and  g round  c onnec tions 
are c omp leted . 
Interconnect Cabling Release 8r 
For fib er op tic  c ab ling  information and  c omc od e numb ers, refer to DEFINITY 
Enterp rise Communic ations Server Release 8 Installation and  Test for Multic arrier 
Cab inets
. The fib er c onnec tions installed  in this sec tion are later ad ministered  
using the fib er link ad ministration instruc tions in Appendix A, ‘‘Fiber Link 
Administration’’. 
NOTE:
Use multi-mod e fib er transc eivers and  fib er op tic  c ab les b etween c ab inets 
unless sing le-mode is req uired  for d istanc e restric tions. 
Direct-Connect New EPN to Existing PPN
(Standard Reliability)
Figure 6-14. Rear of J58890AH Control Carrier (PPN)
0063_0 RBP 071096
98 7 6 5
43 2 1
P1P2
TERMINALDUPLICATION
OPTION
TERMINAL PROCESSOR
INTERFACEDATA
COMMUNICATION
EQUIPMENTAUX CLOCK 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Adding or Removing Cabinet Hardware 
6-24 Install a New EPN Cabinet in an Existing System 
6
1. Install a 9823A lig htwave transc eiver onto Slot 1 on the rear of the PPN 
Control Carrier. See Figure 6-14
.
2. Connec t a 20-foot fib er op tic  c ab le to the TX and  RX c onnec tors on the 
transc eiver. Lab el the c ab le to make the c onnec tions to the EPN c ab inet 
easier. 
3. Route the fib er c ab le to the J58890AF Exp ansion Control Carrier in the 
EPN  c a b i n e t .
4. On the rear of the EPN Exp ansion Control Carrier, install a 9823A 
lig htwave transc eiver onto Slot 2. 
5. Connec t the 20-foot fib er op tic  c ab le from the PPN Control Carrier to the 
TX and  RX c onnec tors on the transc eiver on the EPN Exp ansion Control 
Carrier. Be sure the c ab le c onnec ted  to the TX c onnec tor on the PPN 
transc eiver is c onnec ted to the RX c onnec tor on the EPN transc eiver and  
vic e versa.
Direct-Connect New EPN to Existing PPN (High
or Critical Reliability) 
1. On the rear of the Dup lic ated  Control Carrier, install a 9823A lig htwave 
transc eiver onto Slot 1. 
2. Connec t a 20-foot fib er op tic  c ab le to the TX and  RX c onnec tors on the 
transc eiver. Lab el the c ab le to make the c onnec tions to the EPN c ab inet 
easier. 
3. Route the fib er c ab le to the J58890BB Port Carrier in position C in the EPN 
c ab inet.
4. On the rear of the Port Carrier, install a 9823A lig htwave transc eiver onto 
Slot 2. 
5. Connec t the 20-foot fib er op tic  c ab le from the PPN Dup lic ated  Control 
Carrier to the TX and  RX c onnec tors on the transc eiver on the EPN Port 
Carrier. Be sure the c ab le c onnec ted  to the TX c onnec tor on the PPN 
transc eiver is c onnec ted to the RX c onnec tor on the EPN transc eiver and  
vic e versa. 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Adding or Removing Cabinet Hardware 
6-25 Install a New EPN Cabinet in an Existing System 
6
Direct-Connect New EPN to Existing PPN and
EPN (Standard Reliability)
For the following  c onnec tion examp le, the PPN c ab inet is c alled  Cab inet 1, the 
first EPN c ab inet (next to the PPN c ab inet) is c alled  Cab inet 2, and  the last EPN 
c ab inet is c alled  Cab inet 3.
1. At the rear of the Port Carrier in p osition C in Cab inet 1, install a 9823A 
lig htwave transc eiver onto Slot 2.
2. Connec t a 20-foot fib er op tic  c ab le to the TX and  RX c onnec tors on the 
transc eiver. Lab el the c ab le to make the c onnec tions to Cab inet 3 easier.
3. Route the fib er c ab le to the Exp ansion Control Carrier in Cab inet 3.
4. At the rear of the Expansion Control Carrier in Cabinet 3, install a 9823A 
lig htwave transc eiver onto Slot 1.
5. Connec t the 20-foot fib er op tic  c ab le from the Port Carrier in Cabinet 1 to 
the TX and  RX c onnec tors on the transc eiver on the Exp ansion Control 
Carrier in Cab inet 3. Be sure the c ab le c onnec ted  to the TX c onnec tor on 
1 transc eiver is c onnec ted  to the RX c onnec tor on the other transc eiver 
and  vic e versa.
6. At the rear of the Expansion Control Carrier in Cabinet 3, install a 9823A 
lig htwave transc eiver onto Slot 2.
7. Connec t a 20-foot fib er op tic  c ab le to the TX and  RX c onnec tors on the 
transc eiver. Be sure to lab el the c able.
8. At the rear of the Expansion Control Carrier in Cabinet 2, install a 9823A 
lig htwave transc eiver onto Slot 2.
9. Connec t the 20-foot fib er op tic  c ab le from Cab inet 2 to the TX and  RX 
c onnec tors on the transc eiver on the Exp ansion Control Carrier in Cab inet 
3. Be sure the c ab le c onnec ted  to the TX c onnec tor on 1 transc eiver is 
c onnec ted  to the RX c onnec tor on the other transc eiver and  vic e versa.
10. At the rear of the Expansion Control Carrier in Cabinet 2, install a 9823A 
lig htwave transc eiver onto Slot 1.
11. Connec t a 20-foot fib er op tic  c ab le to the TX and  RX c onnec tors on the 
transc eiver on the Exp ansion Control Carrier in Cab inet 2.
12. Route the fib er c ab le to the Port Carrier in position B in Cab inet 1.
13. Install a 9823A lig htwave transc eiver onto Slot 2 on the Port Carrier in 
p osition D in Cab inet 1.
14. Connec t the 20-foot fib er op tic  c ab le from Cab inet 2 to the TX and  RX 
c onnec tors on the transc eiver on the Port Carrier in Cab inet 1. Be sure the 
c ab le c onnec ted  to the TX c onnec tor on 1 transc eiver is c onnec ted  to the 
RX c onnec tor on the other transc eiver and  vic e versa. 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Adding or Removing Cabinet Hardware 
6-26 Install a New EPN Cabinet in an Existing System 
6
Direct-Connect New EPN to Existing PPN and
EPN (High or Critical Reliability)
For the following  c onnec tion examp le, the PPN c ab inet is c alled  Cab inet 1, the 
first EPN c ab inet (next to the PPN c ab inet) is c alled  Cab inet 2, and  the last EPN 
c ab inet is c alled  Cab inet 3. 
1. At the rear of the Port Carrier in p osition C in Cab inet 1, install a 9823A 
lig htwave transc eiver onto Slot 2.
2. Connec t a 20-foot fib er op tic  c ab le to the TX and  RX c onnec tors on the 
transc eiver. Lab el the c ab le to make the c onnec tions to Cab inet 2 easier.
3. Route the fib er c ab le to the Exp ansion Control Carrier in Cab inet 2.
4. At the rear of the Expansion Control Carrier in Cabinet 2, install a 9823A 
lig htwave transc eiver onto Slot 1.
5. Connec t the 20-foot fib er op tic  c ab le from the Port Carrier in Cabinet 1 to 
the TX and  RX c onnec tors on the transc eiver on the Exp ansion Control 
Carrier in Cab inet 2. Be sure the c ab le c onnec ted  to the TX c onnec tor on 
1 transc eiver is c onnec ted  to the RX c onnec tor on the other transc eiver 
and  vic e versa.
6. At the rear of the Expansion Control Carrier in Cabinet 2, install a 9823A 
lig htwave transc eiver onto Slot 2.
7. Connec t a 20-foot fib er op tic  c ab le to the TX and  RX c onnec tors on the 
transc eiver. Be sure to lab el the c able.
8. At the rear of the Expansion Control Carrier in Cabinet 3, install a 9823A 
lig htwave transc eiver onto Slot 2.
9. Connec t the 20-foot fib er op tic  c ab le from Cab inet 2 to the TX and  RX 
c onnec tors on the transc eiver on the Exp ansion Control Carrier in Cab inet 
3. Be sure the c ab le c onnec ted  to the TX c onnec tor on 1 transc eiver is 
c onnec ted  to the RX c onnec tor on the other transc eiver and  vic e versa.
10. At the rear of the Expansion Control Carrier in Cabinet 3, install a 9823A 
lig htwave transc eiver onto Slot 1.
11. Connec t a 20-foot fib er op tic  c ab le to the TX and  RX c onnec tors on the 
transc eiver on the Exp ansion Control Carrier in Cab inet 3.
12. Route the fib er c ab le to the Port Carrier in position D in Cab inet 1.
13. At the rear of the Port Carrier in p osition D in Cab inet 1, install a 9823A 
lig htwave transc eiver onto Slot 2.
14. Connec t the 20-foot fib er op tic  c ab le from Cab inet 3 to the TX and  RX 
c onnec tors on the transc eiver on the Port Carrier in Cab inet 1. Be sure the 
c ab le c onnec ted  to the TX c onnec tor on 1 transc eiver is c onnec ted  to the 
RX c onnec tor on the other transc eiver and  vic e versa. 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Adding or Removing Cabinet Hardware 
6-27 Install a New EPN Cabinet in an Existing System 
6
Interconnect Cabling Release 8r 
For more fib er op tic  c ab ling information, refer to DEFINITY Enterp rise 
Communications Server Release 8 Installation and Test for Multicarrier Cabinets
.
Switch-Connect New EPN to Existing PPN and
EPN (Standard Reliability)
For the following  c onnec tion examp le, the PPN c ab inet is c alled  Cab inet 1, the 
first EPN c ab inet is c alled  Cab inet 2, and  the EPN c ab inet c ontaining  the Switc h 
Nod e Carrier is c alled  Cab inet 4.
NOTE:
For the following  examp le, ad d  links to PNs in alternating  ord er, for 
examp le: 20 and  2, 19 and  3, 18 and  4, and so forth.
1. At the rear of the Port Carrier in p osition B in Cab inet 1, install a 9823A 
lig htwave transc eiver onto Slot 2 (1B02). See Figure 6-15
.
2. Connec t a 20-foot fib er op tic  c ab le to the TX and  RX c onnec tors on the 
transc eiver. Lab el the c ab le to make the c onnec tions to Cab inet 4 easier. 
3. Route the fib er c ab le to the Port Carrier in position E in Cab inet 4. 
4. At the rear of the Port Carrier in p osition E in Cab inet 4, install a 9823A 
lig htwave transc eiver onto Slot 2 (4E02).
5. Connec t the 20-foot fib er op tic  c ab le from the Port Carrier in Cabinet 1 to 
the TX and RX c onnec tors on the transc eiver on the Port Carrier in Cab inet 
4. Be sure the c ab le c onnec ted  to the TX c onnec tor on 1 transc eiver is 
c onnec ted  to the RX c onnec tor on the other transc eiver and  vic e versa.
6. At the rear of the Expansion Control Carrier in Cabinet 2, install a 9823A 
lig htwave transc eiver onto Slot 1 (2A01).
7. Connec t a 20-foot fib er op tic  c ab le to the TX and  RX c onnec tors on the 
transc eiver. Be sure to lab el the c able.
8. At the rear of the Switc h Nod e Carrier in p osition E in Cab inet 4, install a 
9823A lig htwave transc eiver onto Slot 20 (4E20).
9. Connec t the 20-foot fib er op tic  c ab le from Cab inet 2 to the TX and  RX 
c onnec tors on the transc eiver on the Switc h Nod e Carrier in Cab inet 4. Be 
sure the c ab le c onnec ted  to the TX c onnec tor on 1 transc eiver is 
c onnec ted  to the RX c onnec tor on the other transc eiver and  vic e versa.
10. Connec t an H600-278 Metallic  Cab le from Slot 1 in the Exp ansion Control 
Carrier in Cab inet 4 (4A01) to Slot 19 on the Switc h Nod e Carrier in 
p osition E in Cab inet 4 (4E19). 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Adding or Removing Cabinet Hardware 
6-28 Install a New EPN Cabinet in an Existing System 
6
Figure 6-15. Switch-Connected Release 8r with SNC in EPN
Switch-Connect New EPN to Existing PPN and
EPN (High Reliability)
For the following  c onnec tion examp le, the PPN c ab inet is c alled  Cab inet 1, the 
first EPN c ab inet is c alled  Cab inet 2, and  the EPN c ab inet c ontaining  the Switc h 
Nod e Carrier is c alled  Cab inet 4.
NOTE:
For the following  examp le, ad d  links to PNs in alternating  ord er, for 
examp le: 20 and  2, 19 and  3, 18 and  4, and so forth. Figure Notes:
1. Cab inet 1 (PPN)
2. Cabinet 4 (MCC EPN with One Switc h 
Node)
3. Cab inet 2, 3, and  5 through 16 
(MCC or SCC EPNs)