Lucent Technologies DEFINITY Enterprise Communications Server Release 8.2 Upgrades And Additions Manual

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Adding or Removing Cabinet Hardware 
6-79 Add TTC Japanese 2Mbit Trunks 
6
Add TTC Japanese 2Mbit Trunks
The TN2242 Jap an 2Mb it trunk interc onnec ts DEFINITY with other vend or 
eq uip ment in Jap an as well as to interc onnec t other DEFINITY switc hes throug h 
the Time Division Multip lexor d evice.
Installation
1. Determine the p ort assig nment of the trunk from the Trunk Group  sc reen.
2. Install a TN2242 c irc uit p ac k in assigned  c arrier slot.
3. Connec t the H600-513 c ab le from the DEFINITY c ab inet to the Time 
Division Multip lexor d evice.
4. To ad minister forms, see the following  sec tions in the 
DEFINITY Enterp rise 
Communic ations Server Release 8 Ad ministrator’s Guid e
.
nFor ISDN ap p lic ations, see the “ ISDN Servic e”  sec tion.
nFor non-ISDN ap p lic ations, see the “ Manag ing  Trunks”  sec tion. EXAMPLE:
1 A 07 01
Cabinet (Port 
Network)Carrier Slot 
Numb erPo r t  
Numb er 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Adding or Removing Cabinet Hardware 
6-80 Add a Control Carrier (Add Duplication) 
6
Add a Control Carrier (Add 
Duplication)
To upg rad e a stand ard -reliability system to a hig h- or c ritic al-reliab ility DEFINITY 
ECS Release 5 system, a sec ond  c ontrol c arrier is add ed  to c arrier p osition “ B”  
of the existing  multic arrier c ab inet PPN.
Service Interruption
1. Sinc e the ad d ition of the sec ond c ontrol c arrier req uires a servic e 
interrup tion, notify the c ustomer in ad vanc e as to when the ad d ition will b e 
c arried  out.
Verify System Status
1. Before proc eed ing , the system should  b e examined  for alarms, and  every 
p rob lem should be c orrec ted. The system must b e alarm-free.
Disable Alarm Origination
1. Type change system-parameters maintenance
 and press En t e r.
2. Make a note of the Alarm Origination Activated 
field 
ad ministration. If the feature is enab led , typ e n
 in this field  and  p ress 
En t e r 
to d isab le Alarm Orig ination. This will b e ac tivated  ag ain later. 
!WARNING:
If you d o not d isab le Alarm Orig ination b efore making  c hang es to the 
switc h, the switc h may g enerate alarms, resulting  in unnec essary 
troub le tic kets. Red uc ing  red und ant and  unnec essary troub le tic kets 
is c ritic al for measuring  the q uality of Luc ent servic es and  p rod uc ts.
NOTE:
For earlier releases of the system software, you may also need  to 
disable Cleared Alarm Notification 
and  Restart 
Notification
 field s b efore you c an sub mit the form suc c essfully. 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Adding or Removing Cabinet Hardware 
6-81 Add a Control Carrier (Add Duplication) 
6
Save Translations
1. Log  in at the manag ement terminal.
2. Type save translation [spe-a] disk
 and press 
En te r. This command 
instruc ts the system write all translation information from memory to d isk.
3. If the PPN or an EPN (where PPN Port Carrier B will b e reloc ated ) c ontains 
a TN750 Announc ement c irc uit p ac k, type display announcements
 and 
p ress 
En t e r.
4. If administered  rec ord ed  announc ements are listed , typ e list 
configuration software-version
 and  p ress 
En t e r. Chec k sc reen 2 to see 
when the announc ements were last saved . Save the c urrent 
announc ements b y typ ing  save announcements
 disk
 and pressing 
En t e r.
5. Type backup disk [spe-a]
 and  press 
En t e r. This instructs the system to 
b ac kup  the c urrent information on d isk to the system tap e.
6. Up d ate b ac kup  tape, if req uired .
Label Cables
1. To make rec onnec ting  the c ab les simp ler and  more reliable, lab el b oth 
end s of the c onnec tor c ab les assoc iated  with the p ort c arrier “ B”  to b e 
removed .
Shut Down DEFINITY LAN Gateway System
If a DEFINITY LAN Gateway system resid es in the c ontrol c ab inet to b e 
up g rad ed , p rep are to shut d own the DEFINITY LAN Gateway assemb ly and  
allow the disk to c omp letely sp in d own.
!CAUTION:
Before using this p roc ed ure to shut down the DEFINITY LAN Gateway, 
make sure that you save the system p arameters if you p lan to reuse the 
c urrent system.
!WARNING:
Neg lec ting  to shut d own a DEFINITY LAN Gateway assemb ly b efore 
p owering  d own the system c ab inet where it resides c an d amage the LAN 
Gateway d isk.
1. Log  onto the DEFINITY LAN Gateway. See DEFINITY Communic ations 
System Generic  3 Installation, Ad ministration and  Maintenanc e of 
CallVisor ASAI over the DEFINITY LAN Gateway
 for the p roc ed ure to log  
in.
2. When the main menu ap p ears, selec t 
Maintenanc e. 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Adding or Removing Cabinet Hardware 
6-82 Add a Control Carrier (Add Duplication) 
6
3. Select Reset System from the Maintenanc e menu.
4. Select 
Sh u t d o w n from the Res et Sy ste m menu.
5. Unseat the LAN Gateway assemb ly from its b ac kp lane c onnec tors.
Shut Down DEFINITY AUDIX System
1 . I f  a  D EFI N I TY AU D I X re s i d e s in  t h e  PPN  o r  a n  EPN  (w h e re  PPN  Po r t  
Carrier B will b e reloc ated ), shut d own the AUDIX and allow the d isk to 
c omp letely sp in d own. Refer to ‘‘DEFINITY AUDIX Power Procedures’’ on 
page 6-141.
!WARNING:
Neg lec ting  to shut d own an AUDIX assembly b efore p owering  d own 
the system c ab inet where it resides c an damag e the AUDIX d isk.
2. Unseat the AUDIX assemb ly from its b ac kp lane c onnec tors.
Power Down Port Networks
1. At the PPN, set the main c irc uit b reaker to OFF.
2. At an EPN (where PPN p ort c arrier B will b e reloc ated ), set the main c irc uit 
b re a k e r  t o  O FF.
Remove Doors and Panels and Disconnect Cables
1. Remove the front d oor from the PPN c ab inet.
2. With the c ab le retainer in front of you and  the p art numb er visib le, loc ate 
the slot that is almost vertic al. (This slot is adjac ent to the p art numb er.) 
Insert a flat b lade sc rewd river with a wid e b lad e (1/4-inc h rec ommend ed ) 
into the slot, and  twist. The retainer snap  op ens easily so that the c ab le 
can be removed.
3. At the c ab inet, d isc onnec t p reviously lab eled  c ab les assoc iated  with the 
carrier to be removed.
4. Remove the b ac k d oors from the c abinet. 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Adding or Removing Cabinet Hardware 
6-83 Add a Control Carrier (Add Duplication) 
6
Remove Circuit Packs from Port Carrier B
1.To ensure that c irc uit p ac ks and  p ower units in the “ B”  c arrier are p rop erly 
rep lac ed , lab el eac h c omp onent with its slot numb er.
2. Disc onnec t the p ower c ords from the p ower units in the “ B”  c arrier.
3. Remove all c irc uit p ac ks and  p ower units from c arrier “ B.”  Store the c irc uit 
p ac ks in the static -p roof p ac kag ing .
4. Remove the c irc uit p ac k b lanks from slots that d o not c ontain c irc uit 
p acks.
5. Remove the front trim p late from the “ B”  c arrier b y p ulling  it straig ht off.
Remove Port Carrier B
1. Behind  the PPN, d isc onnec t and  remove the ICCB c ab le from b etween 
c arrier “ B”  and  c arrier “ A.”  It will not b e reused.
NOTE:
Note the p osition of the TDM/LAN c ab les b efore d isc onnec ting  
them.
2. Disc onnec t 1 end  of the TDM/LAN c ab le (b etween the “ B”  and  “ C”  
c arriers) from the “ B”  c arrier (See Figure 6-28
).
3. Disc onnec t 1 end  of the TDM/LAN c ab le (b etween the “ B”  and  “ A”  
c arriers) from the “ B”  c arrier (See Figure 6-28
).
4. Disc onnec t 1 end  of the 8 g round  strap s (b etween the “ B”  and  “ C”  
c arriers) from the “ B”  c arrier (See Figure 6-29
). These straps are 
rec onnec ted  to the new “ B”  c arrier.
5. Disc onnec t 1 end  of the 8 g round  strap s (b etween the “ B”  and  “ A”  
c arriers) from the “ B”  c arrier (See Figure 6-29
). These straps are 
rec onnec ted  to the new “ B”  c arrier.
6. Disc onnec t the “ P1”  (small 9-p in) c onnec tor from the “ B”  c arrier. Move the 
c ab le into a p osition where it will not interfere with removing  the c arrier.
7. Behind the “B” c arrier, remove the 2 screws holding the “ B” carrier’s rear 
c onnec tor p anel to the c ab inet frame. These are frame g round  sc rews.
8. In front of “ B”  c arrier, remove the 4 sc rews (top  2 first) hold ing the “ B”  
c arrier to the c ab inet frame. Use a long -hand le sc rewd river or 5/16-inc h 
soc ket with a 10-inc h extension. 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Adding or Removing Cabinet Hardware 
6-84 Add a Control Carrier (Add Duplication) 
6
9. Slid e the c arrier forward  1 to 2 inc hes; then, from the b ac k, b e sure that no 
c ab les or wiring  harnesses are c aug ht on the c ab inet/c arrier framework.
!CAUTION:
Cab les and  wiring harnesses c an be d amag ed  if they c atc h on the 
framework and  if too muc h pressure is ap p lied  in removing  the 
carrier.
10. Remove the c arrier b y slid ing  it out the front of the c ab inet.
Figure 6-28. TDM/LAN Connections for Standard-Reliability PPN
CONTROL CARRIER
SLOT 21
B
A
D
PORT CARRIER
PORT CARRIER SLOT 21
PORT CARRIER
TDM/LAN BUS
TERMINATOR
SLOT 21
E
(ZAHF4)
SLOT 21
C
REAR VIEWPORT CARRIER (ZAHF4)
SLOT 21
J58890AP-1 J58890BB
J58890BB
J58890BB
J58890BB SEE NOTE SEE NOTE SEE NOTE SEE NOTE
NOTE:
ON PORT CARRIER J58890BB-1, CONNECT THE TDM/LAN CABLE OR TDM/LAN TERMINATOR TO
SLOT 02.  ON PORT CARRIERS J58890BB-2 AND -3, CONNECT THE TDM/LAN CABLES TO SLOT 01.
SLOT 01 TDM/LAN BUS TERMINATOR
TDM/LAN CABLE
WP91716 L6
TDM/LAN CABLE
WP91716 L7
TDM/LAN CABLE
WP91716 L6 TDM/LAN CABLE
WP91716 L6 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Adding or Removing Cabinet Hardware 
6-85 Add a Control Carrier (Add Duplication) 
6
Figure 6-29. Locations of Ground Jumpers on standard and enhanced fan-unit cabinetsFigure Notes
1. Port Carrier C
2. Port Carrier B
3. Ground  Jump ers
4.Control Carrier “ A”  5. Port Carrier “ D”
6. Port Carrier “ E”
7. Cabinet with standard  fan unit and  c arriers
8. Cabinet with enhanc ed  fan unit and  enhanc ed  
carriers
P1 P2P1
P2
P1P1
P1P1
P1P1
P1P1
lcdf004 LJK 021700
11
33
44
55
66
78
3322 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Adding or Removing Cabinet Hardware 
6-86 Add a Control Carrier (Add Duplication) 
6
Prepare New Control Carrier B
1. Visually inspec t the new c arrier for any d amag e. Verify that the b ac kp lane 
pins are not bent.
NOTE:
The enhanc ed  R8r PPN AC c arrier may look d ifferent than the other 
c arriers bec ause it c omes with 16 new g round ing  jumpers and  8 
mounting  sc rews.
2. Plac e the c ontrol c arrier on the floor so that the rear of the c arrier fac es up .
3. Verify that the 2 AHF111 p roc essor-b us (PX) terminators are installed  on 
the “ B”  c arrier to the pin-field  b loc ks marked  “ PX”  (top  p ortion of slots “ 4”  
and  “ 10” ). The PX terminators are attac hed  with the c omp onents on the 
left sid e as viewed from the rear.
Install New Control Carrier B
1. Install the J58890AP c ontrol c arrier in p osition “ B”  b y lining  up  the plastic  
alig nment tip s on the top  rear of the c arrier with the sc rew holes in the 
c ab inet. These alig nment tip s will sup p ort the c arrier while the sc rews are 
b eing  rep lac ed . Ensure that the p ower c ord s are p rop erly plac ed  in the 
slots at the sid es of the c arrier.
2. Fasten the c arrier into p osition with 4 self-tap p ing  sc rews saved  from the 
removal of the old  c arrier.
!CAUTION:
Carefully realig n the thread s on the self-tap ping  sc rews b y turning  
them c loc kwise 1 turn before tightening  them to avoid  strip p ing  the 
thread s out of the framework.
3. Behind  the c arrier, rep lac e the 2 sc rews saved  from the removal of the old  
carrier. These are frame ground screws.
4. Connec t the “ P1”  (small) c onnec tor to the “ B”  c arrier. To g et enoug h slac k 
in the c ab les, c ut the tie wrap  hold ing  the interc ab inet c ab le from the 
up rig ht in the area b eing  installed . Snap  the c onnec tor loc k into p lac e to 
ensure the c onnec tion is prop erly mad e.
5. Connec t the 8 g round  strap s from the “ C”  c arrier to the new “ B”  c arrier 
(See Figure 6-29
). These strap s were left c onnec ted  to the “ C”  c arrier 
when the old “B” c arrier was removed. 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Adding or Removing Cabinet Hardware 
6-87 Add a Control Carrier (Add Duplication) 
6
6.Connec t the 8 g round  strap s from the “ A”  c arrier to the new “ B”  c arrier 
(See Figure 6-29
). These strap s were left c onnec ted  to the “ A”  c arrier 
when the old “B” c arrier was removed.
7. For a stand ard  AC-p owered  c ontrol c arrier, install the 4 c arrier g round  
strap s. The strap s c onnec t g round  p oints G1 and  G8 from the top  of the 
B-c arrier b ac kp lane to the B-c arrier c onnec tor p anel b rac ket and  g round  
p oints G9 and  G16 from the b ottom of the B-c arrier b ac kplane to the 
B-c arrier c onnec tor p anel  b rac ket. 
For an enhanc ed  c arrier, install the 16 c arrier-g round  strap s. The strap s 
c onnec t g round  p oints G1 through G8 from the top  of the B-c arrier 
b ac kp lane to the B-c arrier c onnec tor p anel  and  g round  p oints G9 through 
G16 from the bottom of the B-c arrier b ac kp lane to the B-c arrier c onnec tor 
p anel . Use the 8 sc rews to c onnec t the g round  strap s to the c onnec tor 
p anel  (see Figure 6-30
).
NOTE:
An enhanc ed  c arrier is used  only in an R8r PPN c ab inet that uses 
either AC p ower (U.S.) or Glob al power.
NOTE:
DC-p owered  c ab inets DO NOT use any of the ab ove c arrier-g round  
strap s. 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Adding or Removing Cabinet Hardware 
6-88 Add a Control Carrier (Add Duplication) 
6
Figure 6-30. Locations of Top and Bottom Ground Straps on Standard and 
Enhanced Carriers
8.Connec t the loose end of the TDM/LAN c ab le (b etween the “ C”  and  “ B”  
c arriers) to the p in-field  b loc k marked “ TDM/LAN”  on the right sid e of the 
“B” carrier (See Figure 6-31
 and Table 6-8). The other end  remained  
c onnec ted  to the “ C”  c arrier when the old c arrier was removed . Figure Notes
1. Stand ard  AC-p owered  Carrier
2. Enhanc ed  Carrier (in R8r PPNs using  
either AC p ower [ U.S.]  or Glob al 
power)3. Top  Ground  Strap s
4. Bottom Ground  Strap s
P1P1
12
lcdfgrn2 KLC 022100
G
9G
9
G
1
0
0
00
1
TDM/
LAN
ICCA
ICCB
0
20304
G
1
G
2
7
8 10
11
1
3
2 4 5
6
3
4
3
4