Lucent Technologies DEFINITY Enterprise Communications Server Release 8.2 Upgrades And Additions Manual

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Adding or Removing Cabinet Hardware 
6-89 Add a Control Carrier (Add Duplication) 
6
Figure 6-31. TDM/LAN Connections for High-Reliability PPN
9.Connec t the loose end of the TDM/LAN c ab le (b etween the “ A”  and  “ B”  
c arriers) to the p in-field  b loc k marked “ TDM/LAN”  on the left sid e of the 
“B” carrier (See Figure 6-31
 and Table 6-8). The other end  remained  
c onnec ted  to the “ A”  c arrier when the old  c arrier was removed .
CONTROL CARRIER
SLOT 21
B
A
D
PORT CARRIER
PORT CARRIER SLOT 21
CONTROL CARRIER
TDM/LAN BUS
TERMINATOR
SLOT 21
E
(ZAHF4)
SLOT 21
C
REAR VIEWPORT CARRIER (ZAHF4)
SLOT 21
J58890AP-1 J58890BB
J58890AP-1
J58890BB
J58890BB SEE NOTE SEE NOTESLOT 01 SEE NOTE
NOTE:
ON PORT CARRIER J58890BB-1, CONNECT THE TDM/LAN CABLE OR TDM/LAN TERMINATOR TO
SLOT 02.  ON PORT CARRIERS J58890BB-2 AND -3, CONNECT THE TDM/LAN CABLES TO SLOT 01.
SLOT 00 TDM/LAN BUS TERMINATOR
TDM/LAN CABLE
WP91716 L6
TDM/LAN CABLE
WP91716 L7
TDM/LAN CABLE
WP91716 L6 TDM/LAN CABLE
WP91716 L6 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Adding or Removing Cabinet Hardware 
6-90 Add a Control Carrier (Add Duplication) 
6
10.Connec t the loose end of the TDM/LAN c ab le (b etween the “ C”  and  “ B”  
c arriers) to the p in-field  b loc k marked “ TDM/LAN”  on the right sid e of the 
“B” carrier (See Figure 6-31
 and Table 6-8). The other end  remained  
c onnec ted  to the “ C”  c arrier when the old c arrier was removed .
11. Connec t the loose end of the TDM/LAN c ab le (b etween the “ A”  and  “ B”  
c arriers) to the p in-field  b loc k marked “ TDM/LAN”  on the left sid e of the 
“B” carrier (See Figure 6-31
 and Table 6-8). The other end  remained  
c onnec ted  to the “ A”  c arrier when the old  c arrier was removed .
12. Install the alarm d uplic ation c ab le (H600-198 G1) b etween c arriers “ B”  
and  “ A.”  Connec t the c ab le to the “ ICCA”  p in-field  b loc k (to the rig ht of the 
p in-field  b loc k for slot “ 00” ) of b oth c arriers. See Figure 6-32
. Connec t the 
“UAK”  (up p er) connec tor to carrier “ B,”  and  connec t the “LAK” (lower) 
c onnec tor to c arrier “ A.”
!CAUTION:
While installing  the ICC c ab le c onnec tors, be c areful not to b end  any 
b ac kp lane p ins. Doub le c hec k eac h c onnec tion to verify that the 
p ins are straig ht.
NOTE:
With a c onnec tor in eac h hand , flex the wires within the c ab le’s 
sheath to form a usab le C-shap ed  c ab le.
13. Install the ICCC c ab le (H600-182 G1) b etween c arriers “ B”  and  “ A.”  
Connec t the c ab le to the “ ICCC”  p in-field  b loc k (b ehind  slot “ 01” ) of b oth 
carriers. See Figure 6-32
.
14. Install the d up lic ation c ab le (WP91954 L1) b etween c arriers “ B”  and  “ A.”  
Connec t the c ab le to the “ ICCD”  p in-field  b loc k (b ehind  slot “ 02” ) of b oth 
carriers. See Figure 6-32
.
NOTE:
The d up lic ation c ab le’s c onnec tors are keyed  to ensure p rop er 
p ositioning on the p in-field  b loc k.
Table 6-8. TDM/LAN Connections
“J” Number Carrier Type LHS Slot RHS Slot
J58890BB L1 Port 21 02
J58890BB L2 Port 21 01
J58890BB L3 Port 21 01
J58890AP Control 21 02 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Adding or Removing Cabinet Hardware 
6-91 Add a Control Carrier (Add Duplication) 
6
Figure 6-32. ICC Connections for R8r Control Carrier
15.Install the front trim p late on the “ B”  c arrier.
16. Install the new p ower units into the “ B”  c arrier. The 631DA1 or 644A is 
installed  on the left sid e, while the 631DB1 or 645B and  the 649A are 
installed  on the rig ht side.
17. Connec t the white p ower c ord s to the p ower units. The p ower c ord s are 
eq uip p ed  with p lug s that are run throug h the slots in the front of eac h 
carrier.
Install Circuit Packs
1. Install a new UN330B Dup lic ation Interfac e c irc uit p ac k into c arrier “ A.”  
Use the d ec al as a g uid e.
2. Install the new R8r c ontrol c irc uit p ac ks into c arrier “ B.”  Use the new d ec al 
(provid ed  with the eq uipment) as a g uid e.
3. Install the new TN570B Exp ansion Interfac e c irc uit p ac ks into eac h p ort 
network, and  (if not d up lic ating  a switc h nod e c arrier) interc onnec t the 
p ort networks with the fib er op tic  c ab les.
4. For a c ritic al reliab ility R8r system, install a new TN771D Maintenanc e/Test 
c irc uit p ac k into an availab le p ort slot of eac h EPN (if not alread y p resent).
5. Install c irc uit p ac k b lanks in slots not eq uip p ed  with c irc uit p ac ks.
ROW 49
ROW 35
ROW 25
SLOT #
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
..
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
..
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
..
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
..
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
..
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
05.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
..
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
..
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
..
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
PX
04.
.
.
..
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
..
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
..
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
..
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
..
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
..
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
..
.
.
.
ICCD
02.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
..
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
ICCC
01.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
..
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
..
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
..
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
TDM/LAN
00.
.
.
.
.
.
.
.
.
..
.
.
.
.
.
.
.
.
.
ICCB
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
..
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
ICCA
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
..
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
..
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
..
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
CURL 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Adding or Removing Cabinet Hardware 
6-92 Add a Control Carrier (Add Duplication) 
6
Relocate Port Carrier B
Refer to Add a Switch Node Carrier (High or Critical Reliability) to reloc ate the 
removed port carrier.
Connect Management Terminal or PC
1.Behind  c ontrol c arrier “ A,”  disc onnec t the manag ement terminal or PC 
c ab le from the “ TERM”  c onnec tor, and  rec onnec t the c ab le to the “ DOT”  
(dup lic ation op tion terminal) c onnec tor.
Reseat DEFINITY LAN Gateway System
1. Reseat the LAN Gateway assemb ly into its b ac kp lane c onnec tors. 
Reseat DEFINITY AUDIX System
1 . I f  a  D EFI N I TY AU D I X Sys t e m  re si d e s  in  t h e  PPN  o r  a n  EPN  (w h e re  PPN  
p ort c arrier “ B”  was reloc ated ), reseat the AUDIX assemb ly to its 
b ac kp lane c onnec tors.
Power Up System
1. At an EPN (where PPN p ort c arrier “ B”  was reloc ated ), set the main c irc uit 
breaker to ON.
2. At the PPN, set the main c irc uit b reaker to ON.
3. The system p erforms a level 4 reb ooting  proc ess, load ing  the system 
p rog ram and  d efault or c urrent translations from the disk. Reb ooting  takes 
5 to 11 minutes.
NOTE:
Ig nore alarms for now.
4. Typ e the reset system 4 
and press 
En t e r to c op y the translations from 
removab le media to memory.
5. Clear any alarms.
6. Type save translation [both] 
and press 
En te r  if translation c hang es were 
mad e in Step  8.
7. Type restore disk [both] full
 and  press 
En t e r to c op y the translations from 
removab le media to d isk.
8. Verify that the EMERGENCY TRANSFER CONTROL switc h is set to AUTO. 
This restores the system to the normal operating  mode. 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Adding or Removing Cabinet Hardware 
6-93 Add a Control Carrier (Add Duplication) 
6
Restart DEFINITY LAN Gateway System
1. Log  onto the DEFINITY LAN Gateway.
2. When the main menu ap p ears, selec t 
Maintenanc e.
3. Select 
Reset System from the Maintenanc e menu.
4. Select 
Restart System from the Reset System menu.
Enable SPE Duplication
1. If not also d up lic ating  switc h node c arriers, refer to Duplic ation-Related  
Sys t e m  Pa r a m e t e r s  in  
DEFINITY Enterp rise Communic ations Server 
Release 8 Ad ministrator’s Guid e
, to enab le Switc h Proc essing  Element 
(SPE) duplication.
Enable PNC Duplication
1. For a c ritic al-reliab ility R8r system, type change system-parameters 
customer-options
 and press 
En te r. Use this sc reen to enable the Port 
Network Connec tivity (PNC) dup lic ation op tion. 
Resolve Alarms and Enable Alarm Origination
1. Examine the alarm log . Resolve any alarms using  DEFINITY Enterp rise 
Communic ations Server Release 8 Maintenanc e for R8r
. 
2. If the Alarm Origination Activated
 field  ad ministration is alread y 
set to y
, b e sure to enab le Alarm Orig ination. Otherwise you d o not need  to 
enab le Alarm Orig ination (p roc eed  to the next sec tion).
3. Type change system-parameters maintenance
 and press 
En t e r.
Th e  Alarm Origination Activated
 field  was c hang ed to Alarm 
Origination to OSS Numbers
 to sup p ort more than 1 OSS.
4. Type first-only
 in this field  to enab le Alarm Orig ination (to the first OSS, 
whic h should be INADS). 
Be sure to enter y
 in b oth Cleared Alarm Notification
 and  
Restart Notification
 fields. Press 
En t e r.
5. Type save translation spe-a disk
 and p ress 
En t e r.
NOTE:
The INADS Datab ase Ad ministrator enab les Alarm Orig ination as p art of 
the registration p roc ess.
!WARNING:
If you d o not enab le Alarm Orig ination when the c ustomer has p urc hased  a 
servic es c ontrac t, the switc h will not rep ort any alarm to the TSC 
automatic ally, c ausing the TSC to b e unab le to fulfill the servic es c ontrac t. 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Adding or Removing Cabinet Hardware 
6-94 Add a Switch Node Carrier (Standard Reliability) 
6
Add a Switch Node Carrier (Standard 
Reliability)
To upgrade to a standard reliability R8r with Center Stage Switch (CSS), a switch 
nod e c arrier is ad d ed  either to an emp ty “ E”  c arrier p osition of an existing  
multic arrier p ort network or to the “ D”  c arrier position.
NOTE:
To avoid  moving a p ort c arrier, the p referred  p rac tic e is to plac e the new 
switch nod e c arrier in an emp ty c arrier p osition.
Service Interruption
1. Sinc e the ad d ition of the switc h node c arrier req uires a servic e 
interrup tion, notify the c ustomer in ad vanc e as to when the ad d ition will 
take p lac e.
Verify System Status
1. Before p roc eed ing , examine the system for alarms and  c orrec t all 
p rob lems. The system must b e alarm-free.
Disable Alarm Origination
1. Type change system-parameters maintenance
 and press En t e r.
2. Make a note of the Alarm Origination Activated
 field  
ad ministration. If the feature is enab led , typ e n
 in this field  to disab le 
Alarm Orig ination. 
!WARNING:
If you d o not d isab le Alarm Orig ination b efore making  c hang es to the 
switc h, the switc h may g enerate alarms, resulting  in unnec essary 
troub le tic kets. Reduc ing  red und ant and  unnec essary troub le 
tic kets.
NOTE:
For some releases of the software, d isab le Cleared Alarm 
Notification
 and Restart Notification
 field s b efore 
sub mitting  the form. 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Adding or Removing Cabinet Hardware 
6-95 Add a Switch Node Carrier (Standard Reliability) 
6
Save Translations
1. Log  in at the manag ement terminal.
2. Type save translation disk
 and press 
En te r. This instruc ts the system to 
take all translation information in memory and  write it to the d isk.
3. If the system c ontains a TN750/B Announc ement c irc uit p ac k, type 
display announcements
 and  p ress 
En t e r.
4. If administered  rec ord ed  announc ements are listed , typ e list 
configuration software-version
 and  p ress 
En t e r. Chec k sc reen 2 to find  
out when the announc ements were last saved . Save the c urrent 
announc ements b y typ ing  save announcements disk
 and pressing 
En t e r.
5. Type backup disk
 and  p ress 
En t e r. This instruc ts the system to b ac kup  the 
c urrent information on d isk to the system tap e(s).
6. Up d ate b ac kup  tape(s), if required .
Shut Down DEFINITY LAN Gateway System
If a DEFINITY LAN Gateway system resid es in the c ontrol c ab inet to b e 
up g rad ed , p rep are to shut d own the DEFINITY LAN Gateway assemb ly and  
allow the disk to c omp letely sp in d own. 
!CAUTION:
Make sure that you save the system p arameters if you p lan to reuse the 
c urrent system.
!WARNING:
Neg lec ting  to shut d own a DEFINITY LAN Gateway assemb ly b efore 
p owering  d own the system c ab inet where it resides c an d amage the LAN 
Gateway d isk.
1. Log  onto the DEFINITY LAN Gateway. See the DEFINITY Communic ations 
System Generic  3 Installation, Ad ministration and  Maintenanc e of 
CallVisor ASAI over the DEFINITY LAN Gateway
.
2. When the main menu ap p ears, selec t 
Maintenanc e.
3. Select 
Reset System from the Maintenanc e menu.
4. Select 
Sh u t d o w n from the Res et Sy ste m menu.
5. Unseat the LAN Gateway assemb ly from its b ac kp lane c onnec tors. 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Adding or Removing Cabinet Hardware 
6-96 Add a Switch Node Carrier (Standard Reliability) 
6
Shut Down DEFINITY AUDIX System
1. Shut down the AUDIX assemb ly and  allow the d isk to c omp letely sp in 
d own. Refer to ‘‘DEFINITY AUDIX Power Procedures’’ on page 6-141
.
!WARNING:
Neg lec ting  to shut d own an AUDIX assembly b efore p owering  d own 
the system c ab inet where it resides c an damag e the AUDIX d isk.
2. Unseat the AUDIX assemb ly from its b ac kp lane c onnec tors.
Power Down Cabinet
1. At the c ab inet that is rec eiving  the new switc h nod e c arrier, set the main 
c irc uit b reaker to OFF.
Remove Doors 
1. Remove the front and  rear d oors from the c ab inet where the switc h nod e 
c arrier will b e installed .
Disconnect Ground Cables
Skip these steps if a switch node carrier is being added to an empty carrier 
p osition.
1. Lab el the g round  c ab les assoc iated  with the p ort c arrier to b e removed .
2. Disc onnec t the g round  c ab les from the top  of the port c arrier to b e 
removed . Allow the c ab les to hang  d own for now.
Remove Circuit Packs from Port Carrier D
Skip these steps if a switch node carrier is being added to an empty carrier 
p osition.
1.To ensure that circuit packs and power units in the “D”  carrier are properly 
rep lac ed , lab el eac h c omp onent with its slot numb er.
2. Disc onnec t the p ower c ords from the p ower units in the “ D”  c arrier.
3. Remove all c irc uit p ac ks and p ower units from c arrier “ D.”  Store the c irc uit 
p ac ks in static -p roof p ac kag ing .
4. Remove the c irc uit p ac k b lanks from slots that d o not c ontain c irc uit 
p acks.
5. Remove the front trim p late from the “ D”  c arrier b y p ulling  it straig ht off. 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Adding or Removing Cabinet Hardware 
6-97 Add a Switch Node Carrier (Standard Reliability) 
6
Remove Port Carrier D
Skip these steps if a switch node carrier is being added to an empty carrier 
p osition.
NOTE:
Note the p osition of the TDM/LAN c ab les b efore d isc onnec ting .
1.If a switc h node c arrier is b eing  installed  in the “ D”  p osition of an EPN, 
remove the TDM/LAN c ab le from b etween the “ D”  and  “ A”  c arriers.
For other EPNs or the PPN, d isc onnec t 1 end  of the TDM/LAN c ab le 
(between the “D” and “A” carriers) from the “D” carrier.
2. Remove the ZAHF4 TDM/LAN b us terminator from slot “ 21”  of the “ D”  
carrier.
3. Disc onnec t 1 end  of the 8 g round  strap s (b etween the “ D”  and  “ E”  
carriers) from the “ D” c arrier (See Figure 6-33
). These strap s will b e 
rec onnec ted  to the new “ D”  c arrier.
4. Disc onnec t the 8 g round  straps from the D c arrier (between the “ D”  and  
“ A”  c arriers or the D c arrier and  the enhanc ed  fan unit—see Figure 6-33
). 
Rec onnec t the 8 g round  strap s to the D c arrier.
5. Disc onnec t the “ P1”  (small 9-p in) c onnec tor from the “ D”  c arrier. Move the 
c ab le into a p osition where it will not interfere with removing  the c arrier.
6. Remove the 4 sc rews (top  2 first) hold ing  the “ D”  c arrier to the c ab inet 
frame. Use a long -hand le sc rewd river or 5/16-inc h soc ket with a 10-inc h 
extension.
7. Behind  the “ D”  c arrier in a “ DEFINITY style”  c ab inet, remove the 2 sc rews 
hold ing the “ D”  c arrier to the c abinet frame.
8. Slid e the c arrier forward  1 to 2 inc hes; then, from the b ac k, b e sure that no 
c ab les or wiring  harnesses are c aug ht on the c ab inet/c arrier framework.
!CAUTION:
Cab les and  wiring harnesses c an be d amag ed  if they c atc h on the 
framework and  if too muc h pressure is ap p lied  in removing  the 
carrier.
9. Remove the c arrier b y slid ing  it out the front of the c ab inet. 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Adding or Removing Cabinet Hardware 
6-98 Add a Switch Node Carrier (Standard Reliability) 
6
Figure 6-33. Locations of Ground JumpersFigure Notes
1.Port Carrier (“ C” Position)
2. Ground  Jump ers
3. Control Carrier (“ A”  Position)4. Switc h Nod e Carrier (“ D”  Position)
5. Switc h Nod e Carrier (“ E”  Position)
6. Cabinet with standard  fan unit and  c arrier
7. Cabinet with enhanc ed  fan unit and  
enhanc ed  c arrier
P1 P2
P1
P1
P1
lcdf003 LJK 021800
P1
P2
P1
P1
P1
11
22
22
33
44
55
67