Lucent Technologies DEFINITY Enterprise Communications Server Release 8.2 Upgrades And Additions Manual

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Multicarrier G2 Universal Module to R8r EPN 
5-43 Standard Reliability 
5
Back Up Disk
1. Type backup disk
 and  p ress En t e r to backup all changed files.
2. Type test stored-data long
 and press 
En t e r. This instructs the system to 
verify the c onsistenc y of the MSS files (on the d isk and  removab le med ia).
Return Replaced Equipment
Return unused  G2 eq uip ment to Luc ent Tec hnolog ies ac c ord ing  to the 
req uirements outlined  in:
BCS/Material Log istic s, MSL/Attend ed  Stoc king  Loc ations
Method s and Proc ed ures for Basic  Material Returns 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Multicarrier G2 Universal Module to R8r EPN 
5-44 High Reliability 
5
High Reliability
Required Hardware
The eq uip ment in Table 5-10 must be on-site before the upgrade begins. To 
plac e a claim for missing equipment, as part of the Streamlined Implementation 
p roc ess, c all 1-800-772-5409, or the numb er p rovid ed  b y your Luc ent 
Tec hnolog ies rep resentative.
Table 5-10. Required Hardware
Equipment Description Quantity
J58890A
(PEC 6300-05X)Pro c e s s o r  Po r t  N e t w o r k 1
J58890AF Exp ansion Control Carrier 1
106647985 TN775B Maintenanc e 1
103557294
or
103281788TN776 Exp ansion Interfac e
TN570 Exp ansion Interfac e2 or 6 
1
2 or 6 1,2
1. Use 2 for a hig h reliab ility system with 2 p ort networks; 6 with 3 port networks. Either 1
or 4 Exp ansion Interfac es (EIs) ship loose with the EPN eq uip ment. The factory has
installed  either 1 or 2 EIs in the new PPN.
2. Req uired  port network interfaces in a Release 8 system with the op tional p ac ket bus.
J58890TO-1 L1 Removab le Med ia 4
407439975 20-Foot Multi-mod e Fib er Op tic  Cab le 1 or 3 
3
3. Use 2 or 6 if the PPN and EPN(s) are remotely loc ated . The fib er that p reviously
connec ted  an up g raded  G2 universal module (not a trad itional mod ule) to the G2 TMS
has the c orrec t transc eiver connectors and , therefore, c an b e reused.
106455348
or
1064553639823-A Lig htwave Transc eiver
9823-B Lig htwave Transc eiver2 or 6 4
2 or 6 5
4. One p air for eac h fiber c onnec tion. For eac h c onnec tion, install one 9823-typ e
lig htwave transc eiver in an EPN and  1 in the PPN. A 9823-typ e transceiver c an b e
reused  from eac h upg raded  G2 universal mod ule. Add itional transceivers also ship
loose with the EPN equipment. 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Multicarrier G2 Universal Module to R8r EPN 
5-45 High Reliability 
5
Required Tools
The following tools and  items may b e req uired  d uring  the up g rad e:
nHig h-intensity flashlig ht or AC d rop  lig ht
n3/8-inc h flat-b lad e sc rewd river with a 10-inc h shank (minimum)
n5/16-inc h and  1/4-inc h soc kets with a ratc het and  10-inc h extension
nLong -nose p liers to d isc onnec t ground  straps and  straig hten b ac kplane 
pins
nStatic -p roof or orig inal c irc uit p ac k p ac kag ing  for transp orting  c irc uit 
packs
nLab els for id entifying  the p ort c irc uit p ac ks and  c ab les attac hed  to the 
rear of c ab inets
nTwelve sp are #12 and  #10 self-tap p ing  sc rews
nFour sp are c arrier g round  strap s
nWrist ground strap
nRep air kit for b ac kp lane p ins (KS-22876 L2 or eq uivalent)
nOne c op y of eac h of the following  manuals:
— DEFINITY Enterp rise Communic ations Server Release 8 
Maintenanc e for R8r
— DEFINITY Enterp rise Communic ations Server Release 8 
Ad ministrator’s Guid e
Follow Routine Preventive Maintenance
Follow routine p reventive maintenanc e p roc ed ures on the system to b e 
up g rad ed . For information ab out the p roc ed ures and  nec essary eq uip ment, refer 
to the “ Preventive Maintenanc e”  sec tion in 
DEFINITY Enterp rise Communic ations 
Server Release 8 Maintenanc e for R8r
.
Label Cables
To make rec onnec ting  the c ab les simp ler and  more reliable, lab el b oth end s of 
the c onnec tor c ables assoc iated with the c arrier to b e removed . 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Multicarrier G2 Universal Module to R8r EPN 
5-46 High Reliability 
5
Check Link Status
1. Type display communication-interface links
 and p ress En te r. Write d own 
all enab led  links.
2. Type status link
 
number and  p ress En t e r. Rep eat this step  for all links.
3. Write d own whic h links are in servic e.
Disable TTI
!CAUTION:
If you d o not d isab le the TTI, the translations c an b e c orrup ted .
1. Make sure the ISDN is in servic e. If not, attempt to b usy out and release 
the ISDN D-c hannel/link. This will b ring  the ISDN trunks b ac k into servic e.
2. Type change system-parameters features
 and press 
En t e r. 
3. On the sec ond  sc reen, set the Enabled?
 field  to n
 to p revent the TTI 
feature from ac tivating .
Power Down G2 System
At the power d istribution unit, set the main c irc uit b reaker to OFF.
Install Power-Failure Transfer Ground Wire
!CAUTION:
To avoid  c ontaminating  sing le-p oint g round , d o not c onnec t the g round  wire 
while the system is p owered  up .
1. Connec t a 10 AWG (#25) (2.6 mm2) wire to p in 49 of the c onnec ting  b loc k 
or to pin 49 of the CAP (c ab le ac c ess p anel) on the p ower-failure transfer 
p anel.
2. Route the op p osite end  of the wire to an ap p roved  g round  and  c onnec t. 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Multicarrier G2 Universal Module to R8r EPN 
5-47 High Reliability 
5
Disconnect Cables
1. With the c ab le retainer in front of you and  the p art numb er visib le (4B or 
4C), loc ate the slot that is almost vertic al. This slot is ad jac ent to the p art 
numb er. Insert a #2 flat b lad e sc rewd river into the slot and  twist. The 
retainer will snap  op en easily. Remove the c able.
2. Disc onnec t the c ab les assoc iated  with the c arrier to b e removed .
3. Remove the rear d oors from the c ab inet.
4. Remove all of the rear p anels. Two d ifferent typ es of sc rews hold  the 
p anels to the c ab inet. Remove the #10 sc rews with a sc rewd river or a 
1/4-inc h soc ket. Remove the #12 sc rews with a sc rewd river or a 5/16-inc h 
soc ket.)
Remove Circuit Packs from Module Control 
Carrier A
1.To ensure that p ower units in the “ A”  c arrier are p rop erly rep lac ed , lab el 
eac h p ower unit with its slot number.
2. Disc onnec t the p ower c ords from the p ower units in the “ A”  c arrier.
3. Remove all c irc uit p ac ks and  p ower units from c arrier “ A.”  Store the c irc uit 
p ac ks in the static -p roof p ac kag ing .
4. Remove the c irc uit p ac k b lanks from the emp ty slots.
5. Remove the front trim p late from the “ A”  c arrier b y p ulling  it straig ht off.
Remove CURL from Module Control Carrier A
Remove the CFY1 c urrent limiter (CURL) from the p in-field  b loc k marked  “ CURL”  
on the “ A”  c arrier. The CURL will b e reused  in the Release 8 EPN.
NOTE:
Verify that the CURL meets the minimum usab le vintag e req uirements.
Remove Module Control Carrier A
NOTE:
Note the p osition of eac h TDM/LAN c ab les b efore disc onnec ting .
1. Disc onnec t b oth TDM/LAN c ab les from the “ A”  c arrier. See Figure 5-10
. 
Leave the other end  c onnec ted  to the “ C”  c arrier. 
!CAUTION:
When removing the TDM/LAN c ab les from a previously up g rad ed  
c arrier, b e c areful that none of the short p iec es of shrink tub ing c ome 
off the 4 c orner p ins of the p in-field  b loc k. Otherwise, when the new 
eq uip ment is c onnec ted, -48 volts c ould  short to g round . 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Multicarrier G2 Universal Module to R8r EPN 
5-48 High Reliability 
5
2. On p ort c arrier J58890BB-1, c onnec t the TDM c ab le or TDM terminator to 
Slot 02. On p ort c arriers J58890BB-2 and  J58890BB-3, c onnec t the TDM 
c ab les to Slot 01.
Figure 5-10. TDM/LAN Connections for High Reliability System Figure Notes
1.Port Carrier (“ C” Position)
2. ZAHF4 TDM/LAN Terminator
3. TDM/LAN Cab le (WP91716 L6)
4. Mod ule Control Carrier (“ A”  Position)
5. Port Carrier (“ D” Position)6 . Po r t  C a rr i e r  ( “ E”  Po si t io n )
7. Slot 21
8. Slot 01
9. TDM/LAN Cable (WP91716 L7) 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Multicarrier G2 Universal Module to R8r EPN 
5-49 High Reliability 
5
3.Disc onnec t the 16 g round  strap s from the top  and  b ottom of the “ A”  
c arrier. See Figure 5-11
. These strap s rec onnec t to the new “ A”  c arrier.
Figure 5-11. Locations of Ground Jumpers Figure Notes
1. Rear of Cab inet
2. Port Carrier (“ C” Position)
3. Ground  Jump ers4. Mod ule Control Carrier (“ A”  Position)
5. Port Carrier (“ D”  Position) 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Multicarrier G2 Universal Module to R8r EPN 
5-50 High Reliability 
5
4.Disc onnec t the “ P1”  and  “ P2”  c ab les from the “ A”  c arrier. See Figure 5-12. 
5. Slid e the latc h up , and  d isc onnec t the “ P1”  c ab le from the “ B”  c arrier. 
Figure 5-12. Location of P1 and P2 Connectors
6. Remove the fan trim p late by p ulling  it straig ht off.
7. Clean or rep lac e the air filter (403326820) if nec essary.
8. In the front of the c arrier, remove the 4 sc rews (top 2 first) hold ing  the “ A”  
c arrier to the c ab inet frame. Use a long  hand le sc rewdriver or 5/16-inc h 
soc ket with a 10-inc h (25 c m) extension.
9. Behind  the c arrier, remove the 2 sc rews hold ing  the “ A”  c arrier’s rear 
c onnec tor p anel to the c ab inet frame.
10. Slid e the c arrier forward  1 to 2 inc hes (2.5 to 5 c m). Be sure that no c ab les 
or wiring  harnesses are c aug ht on the c ab inet/c arrier framework.
!CAUTION:
Cab les and  wiring harnesses c an be d amag ed  if they c atc h on the 
framework and  if too muc h pressure is ap p lied  in removing  the 
carrier.
11. Remove the c arrier b y slid ing  it out the front of the c ab inet. Figure Notes
1. Rear of Control Carrier
2. P2 Connec tor3. P1 Connec tor 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Multicarrier G2 Universal Module to R8r EPN 
5-51 High Reliability 
5
Unpack and Inspect Expansion Control Carrier
1. Insp ec t the new J58890AF Exp ansion Control Carrier for any d amag e. 
Also verify that the b ac kp lane p ins are not b ent.
2. Plac e the exp ansion c ontrol c arrier on the floor so that the rear of the 
carrier faces up.
3.Install the CFY1 c urrent limiter (CURL) on the “ A”  c arrier to the p in-field  
b loc k marked  “ CURL.”  Install the CURL with the c omp onents on the left.
4. At the rear c onnec tor p anel, d etermine whic h c onnec tors will have a c ab le 
attac hed , and  install a 4B c ab le retainer on eac h of these c onnec tors.
Install New Expansion Control Carrier A
1. Install the c arrier in p osition “ A”  b y alig ning  the p lastic  alig nment tip s on 
the top  rear of the c arrier with the sc rew holes in the c ab inet. These 
alig nment tip s sup p ort the c arrier while installing  the sc rews. Ensure that 
the p ower c ord s are prop erly p lac ed  in the slots at the sid es of the c arrier.
2. Fasten the c arrier into p osition with the 4 self-tap p ing  sc rews saved  from 
the removal of the old  c arrier.
!CAUTION:
Carefully realig n the thread s on the self-tap ping  sc rews b y turning  
them c ounterc loc kwise 1 turn b efore tig htening  them to avoid  
stripping the threads out of the framework.
3. Behind  the c arrier, rep lac e the 2 sc rews saved  from the removal of the old  
carrier.
4. Connec t the “ P2”  and  “ P1”  c ab les to the “ A”  c arrier. See Figure 5-12
. 
Snap  the c onnec tor loc k into p lac e to ensure the c onnec tion is p rop erly 
mad e.
5. Connec t the “ P1”  c ab le to the “ C”  c arrier. Snap  the c onnec tor loc k into 
p lac e to ensure the c onnec tion is p rop erly mad e.
6. Connec t the 8 g round  strap s from the “ D”  c arrier to the new “ A”  c arrier 
See Figure 5-11
. These straps were left c onnec ted  to the “ D”  c arrier.
7. Connec t the 8 g round  strap s from the “ C”  c arrier to the new “ A”  c arrier. 
These strap s were left c onnec ted  to the “ C”  c arrier.
8. For an AC-powered system, install the 2 new carrier ground straps. One 
strap  c onnec ts g round  point “ 1”  to the A-c arrier frame (rig ht sid e), and the 
other c onnec ts ground  p oint “ 8”  to the A-c arrier frame (left sid e).
NOTE:
DC-p owered  c arriers d o not use these c arrier g round  strap s. 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Multicarrier G2 Universal Module to R8r EPN 
5-52 High Reliability 
5
9.Connec t the remaining end  of the TDM/LAN c able (b etween the “ A”  and  
“ D”  c arriers) to the pin-field  bloc k marked  “ TDM”  on the rig ht sid e of the 
“A” carrier. See Figure 5-13
 and Table 5-11. The other end  remained  
c onnec ted  to the “ D”  c arrier when the old c arrier was removed .
10. Connec t the remaining end  of the TDM/LAN c able (b etween the “ A”  and  
“ C”  c arriers) to the p in-field  b loc k marked  “ TDM”  on the left sid e of the “ A”  
c arrier. The other end remained  c onnec ted  to the “ C”  c arrier when the old  
carrier was removed .
11. On p ort c arrier J58890BB-1, c onnec t the TDM c ab le or TDM terminator to 
Slot 02. On p ort c arriers J58890BB-2 and  J58890BB-3, c onnec t the TDM 
c ab les to Slot 01.