Lucent Technologies DEFINITY Enterprise Communications Server Release 8.2 Upgrades And Additions Manual

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Upgrading R5si/R6si to R8r EPN and Adding Memory 
3-19 Release 5/6si to Release 8r 
3
Figure 3-3. TDM/LAN Connections for Release 5/6si EPN Figure Notes
1. AHF110 TDM LAN/Bus Terminator
2. Slot 17
3. TDM/LAN Cab le (WP91716 L3)
4. Slot 00
5. Slot 036. Slot 18
7.J58890H Port Cab inet (“ D”  
Po si t io n )
8. J58890H Port Cab inet (“ C”  
Po si t io n )  
9. J58890H Port Cab inet (“ B”  Position)
10. J58890NExp ansion Control Cab inet 
(“ A”  Position) 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Upgrading R5si/R6si to R8r EPN and Adding Memory 
3-20 Release 5/6si to Release 8r 
3
Connect TDM/LAN Cables and ICC Cables
1. Route and  c onnec t the TDM/LAN c ab les. If any of the Release 5/6si p ort 
c ab inets (b eing  up g rad ed  to Release 8r c ab inets) were orig inally R1V3 
p ort c ab inets, use the following  step s to route a c ab le b etween an R1V3 
up p er c ab inet and  c ab inet b eneath it. Do not run a new c ab le throug h the 
existing  slot in the rear shelf of the up p er c ab inet.
a. Loosen the 2 left c onnec tor p anel sc rews, then remove the other 2 
c onnec tor p anel sc rews.
b . Attac h the TDM/LAN c ab le to the b ac kp lane and  slid e the c ab le 
b etween the c onnec tor panel and the rear shelf (not throug h the 
existing  slot in the shelf). Route the c ab le along  the b ottom of the 
c ab inet.
c . Rep lac e and  tig hten the c onnec tor p anel sc rews.
2. For a c ritic al reliab ility system, c onnec t the ICC c ab les as shown in Table 
3-4, Figure 3-4, and  Figure 3-5.
NOTE:
For a d up lic ated  c ab inet, d o not use the ICC c ab les (H600-259 G1) 
removed  from the dup lic ated  Release 5/6si PPN. Use the new ICC 
c ab les (H600-248 G1) sup p lied  with the up g rad e.
3.On the “ A”  c arrier, verify the CFY1 c urrent limiter (CURL) c onnec ts to 
p infield  b loc k “ 00”  (see Figure 3-4
).
Table 3-4. Intercabinet Cable Connections
Connect ICC Cables
From To
Carrier Pin-Field Block Carrier Pin-Field Block
EPN J58890N ICCA J58890H ICCA
ICCB ICCB 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Upgrading R5si/R6si to R8r EPN and Adding Memory 
3-21 Release 5/6si to Release 8r 
3
Figure 3-4. ICC Pinfield Blocks on J58890N Expansion Control Cabinet
Figure 3-5. ICC Pinfield Blocks on J58890H Port Cabinet
114 25 12
24
00  00
20 19  20 19
0  3 2 1
2 1  2 1 ICCB ICCA  TERM
CURL
Pinfield
5.00 4.006.00
0  3 2 100
3.00
24
2.001.00 0.00
ICCB
ICCA 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Upgrading R5si/R6si to R8r EPN and Adding Memory 
3-22 Release 5/6si to Release 8r 
3
Interconnect Port Networks with Fiber Optic
Cabling — Standard Reliability Release 8r 
After all fib er op tic  eq uip ment is installed , refer to Chapter A, ‘‘Fiber Link 
Administration’’.
1. Keep  trac k of whic h fib er attac hes to whic h c onnec tor on eac h lig htwave 
transc eiver. Lab el every c ab le installed . This sec tion p rovid es fig ures 
showing  typ ic al examp les of these c onnec tions.
The c onnec tors on the lightwave transc eivers are lab eled  “ TX”  (transmit) or “ RX”  
(rec eive), while the fib ers attac hing  to eac h c onnec tor are numb ered  either “ 1”  or 
“2.” See Figure 3-7
.
Collocated Port Networks
For a stand ard reliab ility system with 1 c olloc ated  EPN, use 1 fib er op tic  c ab le 
and  2 lig htwave transc eivers to d irec tly c onnec t the networks.
For a stand ard  reliab ility system with 2 c olloc ated  EPNs, use 3 fiber optic  c ab les 
and  6 lig htwave transc eivers to d irec tly c onnec t the networks.
NOTE:
Based  on floor p lan c onsid erations, the leng th of these c ab les may vary. 
20-foot (6.1 m) c ab les are normally ad eq uate for a Release 8r with 2 PNs.
For c olloc ated  c ab inets, route the fib er op tic  c ab les d irec tly from the PPN to eac h 
EPN c ab inet. Sinc e a Release 8r PPN c ab inet is c olloc ated  with a Sing le-Carrier 
Cab inet stac k, the p referred  routing  is to run the c ab les 
down the c ab le tray and  
out the b ottom of the PPN c ab inet. The c ab les are then run to the EPN c ab inet 
and  up  the outsid e of the rear p anels to the d esired  c arrier level.
Fiber Remoted Port Networks
For a stand ard reliab ility system with 1 fib er-remoted  EPN, use 2 fib er op tic  
cables,2 lightwave transceivers, and 2 lightguide interface units (provided by the 
PSC ).
For a stand ard reliab ility system with 2 fib er-remoted  EPNs, use 6 fib er op tic  
c ab les, 6 lig htwave transc eivers, and  6 lig htg uid e interfac e units (p rovid ed  b y 
the PSC). 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Upgrading R5si/R6si to R8r EPN and Adding Memory 
3-23 Release 5/6si to Release 8r 
3
DS1 CONV-Remoted Port Networks
For a stand ard reliab ility system with 1 DS1 CONV-remoted  EPN, use 2 DS1 
CONV c irc uit p ac ks (TN1654), 2 DS1 Conv-to-EI c ab les (846448637 and /or 
846448645), two H-600-348 c ables, from 1 to 4 p airs of Channel Servic e Units 
(CSUs), and  from 1 to 4 p airs of MDF c ab les (p rovid ed  with the CSUs).
NOTE:
The TN1654 requires the use of a TN573B Switc hed  Nod e Interfac e c irc uit 
pack
For a stand ard reliab ility system with 2 DS1 CONV-remoted  EPNs, this 
arrang ement req uires:
n6 DS1 CONV c irc uit p ac ks (TN1654)
n6 DS1 CONV-to-EI c ab les (846448637 and /or 846448645)
n6 H-600-348 c ab les
n3, 6, 9, or 12 p airs of CSUs
n3, 6, 9, or 12 p airs of wall-field  c ab les (p rovided  with CSUs)
n5, 10, or 15 d B attenuators (sing le-mod e fib er only)
For 1 or 2 Collocated Expansion Port Networks
1. Behind  p ort c arrier B of the multic arrier PPN. See Figure 3-6 and  Figure 
3-7:
a. Install a lig htwave transc eiver on the c onnec tor at slot 1B02.
NOTE:
Attenuators may be required for single mode fiber using a 
300A Lightwave Transc eiver
b . Connec t 1 end  of the ap p rop riate fib er op tic  c ab le to the lig htwave 
transc eiver at slot 1B02.
c . Route the fib er optic  c ab le from the lig htwave transc eiver to the 
c ab inet’s c ab le tray and  d own out of the c ab inet to the EPN stac k.
d . Carefully attac h the fib er op tic  c ab le (with c ab le ties) to the wall of 
the c ab le tray at the b uilt-in c ab le tie p ositions. 5d B Attenuator 106060718
10d B Attenuator 106060734
15d B Attenuator  106061021 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Upgrading R5si/R6si to R8r EPN and Adding Memory 
3-24 Release 5/6si to Release 8r 
3
2. Behind control cabinet A of EPN stack 2:
a. Install a lig htwave transc eiver on the c onnec tor at slot 2A01.
b . Connec t the other end  of the fiber op tic  c able from the PPN to the 
lig htwave transc eiver at slot 2A01.
c . Carefully attac h the fib er op tic  c ab le (with c ab le ties) to the rear 
c overs of the EPN stac k.
d . Coil up  the surp lus leng th of fib er op tic  c ab le, and  p lac e the c oil 
either in the c ab le manag er or on the b ottom shelf (hold ing  the 
p ower sup p ly) of the PPN c ab inet.
Figure 3-6. Standard Reliability Release 8r with 2 or 3 Port NetworksFigure Notes
1. Cabinet 1 PPN
2. Cabinet Stac k 2 EPN 1
3. Cabinet Stac k 3 EPN 24. From Cab inet 3 A1 to Cab inet 1 C2
5. From Cab inet 2 A2 to Cab inet 3 A2
6. From Cab inet 1 B2 to Cab inet 2 A1  
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Upgrading R5si/R6si to R8r EPN and Adding Memory 
3-25 Release 5/6si to Release 8r 
3
Figure 3-7. Typical Fiber Optic Connections
For 1 or 2 Fiber-Remoted Expansion Port 
Networks
1. Behind  p ort c arrier B of the multic arrier PPN. See Figure 3-6 and  Figure 
3-8:
a. Install a lig htwave transc eiver on the c onnec tor at slot 1B02.
NOTE:
Attenuators may be required for single mode fiber using a 
300A Lightwave Transc eiver
b . Connec t a fib er op tic  c ab le to the transc eiver just installed .
c . Route the c ab le to the c ab inet c ab le tray and out of the c ab inet 
throug h the c ab le manag er to the PDS c ross-c onnec t fac ility.
d . Connec t the fib er c ab le to the lig htg uid e interfac e unit p rovided .
e. Carefully attac h the fib er op tic  c ab le (with c ab le ties) to the wall of 
the c ab le tray at the b uilt-in c ab le tie p ositions. Figure Notes
1. Lightwave Transc eiver
2. To PPN Carrier B Slot 1B02
3. To EPN 1 Carrier A Slot 2A01 
(Cab inet Stac k 2)4. Fiber Optic Cable
5. TX Connec tor
6. RX Connec tor
cydff05 CJL 103196
RX TX
2211 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Upgrading R5si/R6si to R8r EPN and Adding Memory 
3-26 Release 5/6si to Release 8r 
3
2. Behind control cabinet A of EPN stack 2:
a. Install a lig htwave transc eiver on the c onnec tor at slot 2A01.
b . Connec t a fib er op tic  c ab le to the transc eiver just installed .
c . Route the c ab le d own the outsid e of the rear c overs and  throug h 
the c ab le manag er to the PDS c ross-c onnec t fac ility.
d . Connec t the fib er op tic  c ab le to the lig htg uid e interfac e unit.
e. Carefully attac h the fib er op tic  c ab le (with c ab le ties) to the rear 
c overs of the EPN stac k.
f. Coil up  the surp lus fib er op tic  c able and  p lac e the c oil in the c ab le 
manag er.
Figure 3-8. Fiber Optic Connections PPN to EPN1 Figure Notes
1. Lightwave Transc eiver
2. PPN Carrier B Slot 1B02
3. EPN 1 Carrier A Slot 2A01 (Cabinet 
Stac k 2)
4. Fiber Optic Cable5. Fib er Op tic  Cross-Connec t Fac ility
6. Lig htg uid e Interfac e Unit (LIU)
7. TX Connec tor
8. RX Connec tor
cydf013 CJL102396
RX TX
2
22 1
11
22
11 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Upgrading R5si/R6si to R8r EPN and Adding Memory 
3-27 Release 5/6si to Release 8r 
3
Interconnect Port Networks with Fiber Optic
Cabling — High Reliability Release 8r 
1. Keep  trac k of whic h fib er attac hes to whic h c onnec tor on eac h lig htwave 
transc eiver. 
This sec tion p rovid es fig ures showing  typ ic al ways of making  these c onnec tions. 
The c onnec tors on the lightwave transc eivers are lab eled  “ TX”  (transmit) or “ RX”  
(rec eive), while the fib ers attac hing  to eac h c onnec tor are numb ered  “ 1”  or “ 2.”  
See Figure 3-10
.
Collocated Port Networks
For a high reliab ility system with 1 c olloc ated  EPN, use 1 fiber op tic  c able and  2 
lig htwave transc eivers, or 1 sing le-mod e fib er op tic  c ab le and  2 sing le-mod e 
lig htwave transc eivers to d irec tly c onnec t the networks.
For a hig h reliab ility system with 2 c olloc ated  EPN, use 3 fib er op tic  c ab les and  6 
lig htwave transc eivers, or 3 sing le-mod e fib er op tic  c ab les and  6 sing le-mod e 
lig htwave transc eivers to d irec tly c onnec t the networks.
NOTE:
Based  on floor p lan c onsid erations, the leng th of these c ab les may vary. 
20-foot (6.1 m) c ab les are normally ad eq uate for a Release 8r with 2 p ort 
networks.
For c olloc ated  c ab inets, route the fib er op tic  c ab les d irec tly from the PPN to eac h 
EPN c ab inet. Sinc e a Release 8r PPN c ab inet is c olloc ated  with a Sing le-Carrier 
Cab inet stac k, the p referred  routing  is to run the c ab les 
down the c ab le tray and  
out the b ottom of the PPN c ab inet. The c ab les are then run to the EPN c ab inet 
and  up  the outsid e of the rear p anels to the d esired  c arrier.
Fiber-Remoted Port Networks
For a hig h reliability system with 1 fib er-remoted  EPN, use 2 fib er op tic  c ab les, 2 
lig htwave transc eivers, and  2 lig htg uid e interfac e units (p rovid ed  b y the PSC).
For a hig h reliab ility system with 2 fiber-remoted  EPNs, use 6 fib er op tic  c ab les, 6 
lig htwave transc eivers, and  6 lig htwave-interfac e units (p rovid ed  by the PSC).
DS1 CONV-Remoted Port Networks
For a high reliab ility system with 1 DS1 CONV-remoted expansion p ort network, 
use 2 DS1 CONV c irc uit p ac ks (TN1654), 2 DS1 CONV-to-EI c ab les (846448637 
and /or 846448645), 2 H-600-348 c ab les, from 1 to 4 pairs of c hannel servic e 
units (CSUs), and  from 1 to 4 p airs of wall-field  c ab les (p rovid ed  with the CSUs).
NOTE:
The TN1654 requires a TN573B Switc h Nod e Interfac e c irc uit p ac k 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Upgrading R5si/R6si to R8r EPN and Adding Memory 
3-28 Release 5/6si to Release 8r 
3
For a high reliab ility system with 2 DS1 Conv-remoted  exp ansion p ort networks, 
this arrang ement req uires:
n6 DS1 Converter c irc uit p ac ks (TN1654)
n6 DS1 Converter-to-EI c ab les (846448637 and /or 846448645)
n6 H-600-348 c ab les
n3, 6, 9, or 12 p airs of CSUs
n3, 6, 9, or 12 p airs of wall-field  c ab les (p rovided  with CSUs)
For 1 or 2 Collocated Expansion Port Networks
1. Behind  p ort c arrier C of the multic arrier PPN. See Figure 3-9 and Figure 
3-10:
a. Install a lig htwave transc eiver on the c onnec tor at slot 1C02.
NOTE:
Attenuators may be required for single mode fiber using a 
300A Lightwave Transc eiver
b . Connec t 1 end  of the ap p rop riate fib er op tic  c ab le to the lig htwave 
transc eiver at slot 1C02.
c . Route the fib er optic  c ab le from the lig htwave transc eiver to the 
c ab inet’s c ab le tray and  d own, out of the c ab inet, to the EPN stac k.
d . Carefully attac h the fib er op tic  c ab le (with c ab le ties) to the wall of 
the c ab le tray at the b uilt-in c ab le tie p ositions.
2. Behind  c ontrol c ab inet A EPN stac k 2:
a. Install a lig htwave transc eiver on the c onnec tor at slot 2A01.
NOTE:
Attenuators may be required for single mode fiber using a 
300A Lightwave Transc eiver
b . Connec t the other end  of the fiber op tic  c able from the PPN to the 
lig htwave transc eiver at slot 2A01.
c . Carefully attac h the fib er op tic  c ab le (with c ab le ties) to the rear 
c overs of the EPN stac k.
d . Coil up  the surp lus fib er op tic  c ab le, and  p lac e the c oil either in the 
c ab le manager or on the b ottom shelf (holding  the p ower supp ly) of 
the PPN c ab inet.