Lucent Technologies DEFINITY Enterprise Communications Server Release 8.2 Upgrades And Additions Manual

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Upgrading G3rV2, V3, V4 to R8r and Adding Memory 
1-5 Task Tables 
1
Verify Interchange (H/C only)1-15
Upgrade other carrier (H/C only)1-15
Affix position label(s)1-15
Verify software version1-16
Save Translations1-16
Save Announcements (if necessary)1-16
Restore Disk1-16
Upgrade Software1-17
Reset SPE status (H/C only)1-17
List Configuration Control1-17
Set Daylight Savings Rules1-18
Set Date and Time1-19
Set Core Dump Vector1-20
Enable TTI1-20
Release MMI (H/C only)1-21
Resolve Alarms1-21
Check Link Status1-21
Enable Scheduled Maintenance1-21
Enable Customer Options and Alarm Origination to INADS1-21
Check SPE status (H/C only)1-22
Save Translations1-22
Save Announcements (if necessary)1-22
Back Up Disk1-23
Return Replaced Equipment1-23
Continued on next page
Table 1-2. Tasks to upgrade the software and hardware  — Continued
ÖTask Description Page 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Upgrading G3rV2, V3, V4 to R8r and Adding Memory 
1-6 Upgrade the software and hardware 
1
Upgrade the software and hardware
Check SPE
1. Type status spe
 and press En t e r to c hec k the health of the SPE. 
For hig h or c ritic al reliab ility systems:
nTh e  Standby Refreshed
 field  shows yes
nTh e  Standby Shadowing
 field  shows on
nTh e  Standby Handshake
 field  shows up
Save Translations
1. Type save translation
 and press En te r to write all translation information 
from memory to the d isk, whic h takes ab out 2 minutes.
Save Announcements (if necessary)
NOTE:
The TN750C Announc ement c irc uit p ac k stores announc ements in 
nonvolatile memory; saving  the announc ements is op tional.
1. If the PPN c ontains a TN750/B Announc ement c irc uit p ac k, typ e display 
announcements
 and  p ress 
En te r.
2. If administered  rec ord ed  announc ements are listed , typ e save 
announcements 
cabinet carrier slot and press En t e r. For example, 
01
D03. This takes ab out 30 minutes.
NOTE:
For some software load s, type save announcements from cabinet 
carrier slot
. Typ e help
 and  p ress En t e r for c omp lete c ommand 
usag e.
Back Up Disk
1. Type backup disk
 and  p ress En t e r to write all information from the d isk to 
the b ac kup  tap e. This takes 30 to 40 minutes.  
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Upgrading G3rV2, V3, V4 to R8r and Adding Memory 
1-7 Upgrade the software and hardware 
1
Disable Scheduled Maintenance and Alarm 
Origination to INADS
1. To p revent sc hed uled  d aily maintenanc e from interfering  with the up d ate 
or up g rad e, typ e change system-parameters maintenance
 and  p ress 
En t e r.
2. If sc heduled maintenanc e has b eg un, set the Stop Time
 field  to 1 minute 
after the c urrent time.
or
If sc hed uled  maintenanc e has not
 b eg un, set the Start Time
 field  to a 
time after the upgrade is completed. For example, if you start the upgrade 
at 8:00 p .m. and  the up g rad e takes 90 minutes, set the Start Time
 field  
to 21:30.
!CAUTION:
If you d o not d isab le Alarm Orig ination, the system may g enerate 
alarms, resulting  in unnec essary troub le tic kets.
3. Type neither 
in the Alarm Origination to OSS Numbers 
field and 
p ress 
En t e r .
NOTE:
For some software load s, set the Alarm Origination 
Activated
 field  to n 
and 
set the Cleared Alarm Notification 
and  Restart Notification
 fields to disable
 or n
 b efore 
pressing 
En t e r. 
Reconfigure the Tape (G3rV2, V3 R31.0 and 
Earlier)
NOTE:
Do not issue the list configuration software 
command before 
reconfiguring the removable media.
For some software load s, use 3-mem
 instead  of large
If stand ard  reliab ility:
1. Type configure tape large
 and press 
En te r to reconfigure the bac kup 
removab le med ia for the 2 TN1650B Memory c irc uit pac ks. This c ommand  
takes ab out 1 minute to c omp lete. 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Upgrading G3rV2, V3, V4 to R8r and Adding Memory 
1-8 Upgrade the software and hardware 
1
If hig h or c ritic al reliab ility:
1. Type configure tape spe-a large
 and press 
En t e r to rec onfig ure the 
removable media in c ontrol c arrier “ A”  for 2 TN1650B Memory c irc uit 
p ac ks. This c ommand  takes ab out 1 minute to c omp lete.
2. Type configure tape spe-b large
 and  p ress 
En te r to rec onfigure the 
removab le media in c ontrol c arrier “ B”  for 2 TN1650B Memory c irc uit 
p ac ks. This c ommand  takes ab out 1 minute to c omp lete.
Check Link Status
1. Type display communication-interface links
 and p ress En te r. Write d own 
all enab led  links.
2. Type status link
 
number and  p ress En t e r. Rep eat this step  for all links.
3. Write d own whic h links are in servic e.
Disable TTI
NOTE:
Do this step only if the Terminal Translation Initialization (TTI) is enab led .
!CAUTION:
If you d o not d isab le the TTI, the translations c an b e c orrup ted .
Make sure the ISDN is in servic e. If not, try to b usy out and  release the ISDN 
D-c hannel/link to b ring  the ISDN trunks b ac k into servic e.
1. Type change system-parameters features
 and press 
En t e r. 
2. On 
the sec ond  sc reen, set the TTI Enabled?
 field to n 
to d e-ac tivate the 
TTI feature.
Check Disk Drive
1. Type list configuration control
 and press En t e r to c hec k the vintag e of the 
d isk drive. If the d rive is V4 or later, g o to Check TTI Status
.
or
If the d rive is 
not V4 or later, g o to Install Disk Drive (if not TN1657 V4 or 
earlier). 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Upgrading G3rV2, V3, V4 to R8r and Adding Memory 
1-9 Upgrade the software and hardware 
1
Install Disk Drive (if not TN1657 V4 or earlier)
!CAUTION:
When rep lac ing  any hardware, b e sure to g round  yourself against 
elec trostatic  d isc harg e (ESD) b y wearing  a g round ed  wrist strap .
!CAUTION:
If a hig h or c ritic al reliab ility system, rep lac e and  restore the d isk d rives one 
a t  a  t i m e  s t a r t in g  w it h  t h e  s t a n d b y  SPE.  N e v e r  re p la c e  t h e  a c t iv e  a n d  
stand b y d isk drives at the same time.
1. Type busyout host-adapter
 [a 
| b
] 
and press En t e r  to p revent other 
ap p lic ations from ac c essing  the d isk or removab le med ia.
2. Remove the existing  TN1657 Disk Drive c irc uit p ac k and  p lac e it in 
antistatic  material.
3. Insert a new TN1657 c irc uit p ac k into the DISK DRIVE slot.
4. To p rop erly seat the c irc uit p ac k, p ush firmly on the front of the fac ep late 
until the latc h reac hes the b ottom rail of the c arrier. Then c lose the latc h 
until it is fully engaged.
5. Type release host-adapter 
[a 
| b
] and  p ress 
En te r  to release the d isk from 
the maintenanc e-b usyout c ond ition and  p ut it b ac k into servic e.
6. Type reset host-adapter 
[a 
| b
] 
and press 
En te r to allow the d isk to sp in 
up .
7. Type status spe
 and press 
En t e r to verify that the d isk is now in servic e.
NOTE:
If the disk fails to return to servic e, rep eat Step s 1, 3, 4, and  5.
For hig h or c ritic al reliab ility, rep eat step s 1 throug h 7 on the ac tive c arrier.
Restore Disk
NOTE:
Until this c ommand finishes, the system p rovid es no user feed b ac k on the 
manag ement terminal sc reen. Do not p ress 
En t e r while the c ommand  
exec utes. Doing  so c auses the terminal sc reen to c lear as the c ommand 
finishes; erasing any suc c ess or failure messag es the system may p rovid e.
If stand ard  reliab ility:
1. Type restore disk full 
and  p ress 
En te r to c op y the information on the 
removab le media to d isk, whic h takes ab out 30 minutes.
If hig h or c ritic al reliab ility:
1. Type restore disk full both
 and press 
En t e r.  
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Upgrading G3rV2, V3, V4 to R8r and Adding Memory 
1-10 Upgrade the software and hardware 
1
Check TTI Status 
1. Type status TTI
 and  p ress En te r. Wait until the Percent Complete
 field  
shows 100%
.
Busyout MMI Circuit Packs (H/C only)
!CAUTION:
Multimed ia-to-voic e station c alls are not p reserved  on an up g rade. Failure to b usy-out 
the TN787 Multimed ia Interfac e (MMI) c irc uit p ac ks results in unusab le TN787 and  
TN788 Multimed ia Voic e Cond itioner p orts.
1. Type display system-parameters customer-options
 and press En t e r. On 
sc reen 2 und er the Multimed ia Call Hand ling  (MMCH) op tions, c hec k the 
Basic
 and  Enhanced
 fields. 
2. If either the Basic
 or Enhanced
 field  is y
, typ e list configuration all
 and 
p ress 
En t e r  to loc ate all MMI (TN787) c irc uit p ac ks.
3. If there are MMI c irc uit p ac ks, typ e busyout board 
cabinet carrier slot 
and  p ress 
En t e r to remove the c irc uit p ac ks from servic e.
Lock the active SPE (H/C only)
1. Type status spe
 and press En t e r to d etermine whic h c ontrol c arrier is 
ac tive or ob serve the c ontrol c arrier LEDs.
NOTE:
For hig h or c ritic al reliab ility systems, we rec ommend  that you 
rep lac e the c irc uit pac ks in the stand b y c arrier first.
!CAUTION:
When rep lac ing  any hardware, b e sure to g round  yourself against 
elec trostatic  d isc harg e (ESD) b y wearing  a g round ed  wrist strap .
2. Move the SPE-SELECT switc hes on b oth Dup lic ation Interfac e (DUPINT) 
circuit packs, 
one at a time, to the ac tive c arrier.  
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Upgrading G3rV2, V3, V4 to R8r and Adding Memory 
1-11 Upgrade the software and hardware 
1
Check the active tone-clock (H/C only)
1. Type status port-network 1
 and  verify that the Tone-Cloc k is in the same 
c a r r ie r a s  t h e  a c t i v e  SPE a n d  t h a t  t h e  Service State
 field  shows in
.
NOTE:
This takes 1 minute to c omp lete. If the servic e state is inc orrec t, 
rep eat the c ommand  until this c ond ition is met.
If the ac tive Tone-Cloc k has not migrated  to the ac tive c arrier after 
1 minute, then a Tone-Cloc k p rob lem exists. Refer to the TDM-CLK 
Maintenanc e Ob jec ts sec tion of the 
DEFINITY Enterp rise Communic ations 
Server Release 8 Maintenanc e for R8r
 b ook to resolve any p rob lems.
Power Down the Processor Carrier
!CAUTION:
Do not p ower d own the whole c ab inet; it is not nec essary.
For stand ard  reliab ility, p ower d own the p roc essor c arrier. This c auses a servic e 
interrup tion.
For high or critical reliability, power down the standby carrier.
1. To power down the processor carrier, remove the power plug from the 
left 
sid e
 of the c arrier then remove the p ower p lug  from the right side of the 
carrier. 
Remove the Circuit Packs
NOTE:
More detailed  information on removing and  add ing  c irc uit p ac ks is in 
Chapter 6, ‘‘Adding or Removing Cabinet Hardware’’
.
1. Remove the b lank fac ep late next to the MSSNET slot in the c arrier.
2. Remove the UN332B circuit pack from the carrier and place it in antistatic  
packing material.
3. Remove the tap e from the tap e d rive.
4. Remove the TN1656 tap e d rive and  p lac e it in antistatic  p ac king  material.  
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Upgrading G3rV2, V3, V4 to R8r and Adding Memory 
1-12 Upgrade the software and hardware 
1
Install the Circuit Packs
NOTE:
To p rop erly seat a c irc uit p ac k, p ush firmly on the front of the fac eplate until 
the latc h reac hes the b ottom rail of the c arrier. Then c lose the latc h until it is 
fully engaged.
1. Insert the TN1650B memory c irc uit p ac k in memory slot 3.
NOTE:
If a hig h or c ritic al reliab ility system, install the TN1650B at the same 
time as the op tic al d rive. Note that add ing  memory to the stand by 
SPE c a u s e s a n  e rro r  b e c a u s e  t h e  m e m o r y n u m b e r b e t w e e n  t h e  
standb y and  ac tive c arriers does not matc h.
2. Insert the UN332C c irc uit p ac k into the MSSNET slot.
3. Rep lac e the b lank fac ep late next to the MSSNET c irc uit p ac k.
4. Insert the TN2211 optical drive (Figure 1-1
) into the rig ht most TAPE DRIVE 
slot. It only takes up 2 slots.
5. Plac e a b lank fac eplate over the left most TAPE DRIVE slot.
Figure 1-1. TN2211 Optical Drive
Red
Green
Yellow
fpdf2211 KLC 010600TN2211 OPTICAL DRIVE 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Upgrading G3rV2, V3, V4 to R8r and Adding Memory 
1-13 Upgrade the software and hardware 
1
6. Plac e the formatted  removab le med ia, lab el fac ing  left, into the op tic al 
drive.
NOTE:
Make sure the formatted removab le med ia is not write-p rotec ted 
b efore p lac ing  it into the op tic al drive 
(see Figure 1-2).
Figure 1-2. Make sure the disk is not write-protected.
!CAUTION:
The removab le media has a slid ing , metal c over to p rotec t the 
surfac e of the d isk. DO NOT TOUCH THE DISK (
Figure 1-3).
Figure Notes
1. Not Write-p rotec ted 2. Write-p rotec ted
h1dfdsk KLC 112499
12 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Upgrading G3rV2, V3, V4 to R8r and Adding Memory 
1-14 Upgrade the software and hardware 
1
Figure 1-3. Do not touch the disk inside the cartridge.
Power Up the Processor Carrier
1. To restore p ower to the p roc essor c arrier, insert the p ower p lug  on the 
right side of the c arrier then insert the p ower p lug  on the left sid e of the 
carrier.
If hig h or c ritic al reliab ility:
2 . M o n it o r t h e  SPE a s  it  re b o o t s b y  o b se r vi n g  t h e  L ED s  a n d  t h e  t e r m in a l.  I t  is  
p owered  up  when the YELLOW LED on the Proc essor c irc uit p ac k b links 
in a stead y state, whic h takes ab out 10 minutes.
Unlock the Active SPE (H/C only)
1. Move the SPE SELECT switc hes to the AUTO position one at a time.
2. Wait 10 minutes.
!CAUTION:
Allow 10 minutes after unlocking to make sure the standby SPE has 
fully returned  to servic e.
640MB
2048BYTES
/S
EC
TO
R
h1dfdsk1 KLC 091799