Lucent Technologies DEFINITY Enterprise Communications Server Release 8.2 Upgrades And Additions Manual

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Adding or Removing Cabinet Hardware 
6-69 Add IP Interface Assembly 
6
11. Typ e d omain name in the Domain
 field .
12. If using  DNS, c lic k 
Add  under the DNS Service Search Order
 field  and 
type its IP ad d ress.
13. Clic k on the WINS Ad dress tab . 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Adding or Removing Cabinet Hardware 
6-70 Add IP Interface Assembly 
6
14. Make sure the [ 2]  DEC shows in the Adapter
 field.
15. If WINS server is availab le, typ e its IP ad d ress in the Primary WINS 
Server
 field .
16. If DNS is availab le, selec t Enable DNS for Windows Resolution
.
17. If the network uses an imp orted LMHOSTS file, selec t Enable LMHOSTS 
Lookup 
and Import LMHOSTS
 and c lic k OK
.
18. If the following  d ialog  b ox op ens, c lic k Ye s
:
At least one of the adapter cards has an empty primary 
WINS address. Do you want to continue?
19. Clic k the Bindings
 tab  to effec t the c hang es.
NetBIOS Interface, Server, and Workstation should now be enabled. If any 
are d isab led  (a red  c irc le with a line throug h it), review the p revious 
network-c onfig uration step s for omissions or errors.
20. Clic k Close
. 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Adding or Removing Cabinet Hardware 
6-71 Add IP Interface Assembly 
6
If administered  remotely throug h p c ANYWHERE:
21. Clic k on the p c ANYWHERE Restart Host Comp uter b utton on the toolb ar 
to restart the c omputer.
If administered  loc ally on a monitor, keyb oard, and  mouse:
21. Clic k Ye s
 in the d ialog  b ox to restart the c omp uter. 
!WARNING:
When c onnec ted  remotely via p c ANYWHERE, only use the p c ANYWHERE 
Restart Host Computer b utton on the toolb ar to restart Wind ows NT.
Check Network Services
When the server restarts, make sure that the req uired  network servic es have 
started c orrec tly. If you see an error d ialog  b ox, then the network servic es d id  not 
start c orrec tly. Also, c hec k the NT Event Log.
1. Click on My Computer > Control Panel > Network > Services. 
Make 
sure that the following  servic es are listed:
nComp uter Browser
nMic rosoft Internet Information Server 2.0
nNetBIOS Interfac e
nRPC Config uration
nSe r ve r
nWorkstation
2. Click the Protocols 
tab , and examine the Network Protoc ols. TCP/IP 
p rotoc ol should  b e the only one listed .
3. Click OK
.
Test the External Connection to the LAN
To test the external IP c onnec tions, p ing  the IP Interfac e server and  p ing  a known 
c omp uter c onnec ted  to your network.
1. Click Start > Programs > Command Prompt
.
2. Type ping 
nnn.nnn.nnn.nnn (whic h is your IP ad d ress).
nIf everything  is c onfigured  c orrec tly, the system respond s with the 
following message:
Reply from nnn.nnn.nnn.nnn: bytes=32 time
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Adding or Removing Cabinet Hardware 
6-72 Add IP Interface Assembly 
6
3. At the c ommand p romp t, type ping nnn.nnn.nnn.nnn (whic h is the IP 
ad d ress of your g ateway). 
nIf everything  is c onfigured  c orrec tly, the system respond s with the 
following message:
Reply from nnn.nnn.nnn.nnn: bytes=32 time Settings > Control Panel > 
Network
. Selec t the Adapters
 tab  and  hig hlight the [ 2]  DEC 
ad ap ter.
nClic k Properties > Change
. 
nFrom the Duplex Mod e d ropd own menu, selec t a setting  that 
matc hes the switc h/hub  that the TN802B c onnec ts to. For examp le, 
10BaseT Full Dup lex or 10BaseT No Link Test
4. At the c ommand p romp t, type ping 
nnn.nnn.nnn.nnn (whic h is the IP 
ad d ress of another external c omp uter beyond  the g ateway). 
nIf you have c onnec tivity, the system respond s with the following  
messag e:
Reply from nnn.nnn.nnn.nnn: bytes=32 time Programs > Command Prompt
.
2. Type ping 
192.11.13.9 (whic h is the IP ad d ress of the internal IP Interfac e 
server). 
nIf everything  is c onfigured  c orrec tly, the system respond s with the 
following message:
Reply from 192.11.13.9: bytes=32 time
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Adding or Removing Cabinet Hardware 
6-73 Add IP Interface Assembly 
6
3. At the c ommand  p romp t, typ e ping 192.11.13.8 (whic h is the IP ad d ress of 
the internal p roc essor). 
nIf you have c onnec tivity, the system respond s with the following  
messag e:
Reply from 192.11.13.8: bytes=32 time
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Adding or Removing Cabinet Hardware 
6-74 Add IP Interface Assembly 
6
Connect the Monitor, Keyboard, and Mouse
1. Attac h a VGA monitor to the VGA c onnec tor of the TN802 IP Interfac e 
external c ab le assemb ly.
2. Attac h the keyb oard  to the KEYBOARD c onnec tor of the external c ab le 
assemb ly.
3. Attach the mouse to the MOUSE connector of the external c able 
assemb ly.
4. Plug  the monitor into an AC p ower rec ep tac le and  turn it on.
5. If upg rad ing  loc ally, reb oot Wind ows NT b y p ressing  the rec essed  reset 
b utton on the fac ep late (see Figure 6-26
) of the TN802B IP Interfac e until 
the LCD shows a flashing  MSHUT *
. When the flashing stops and the 
asterisk d isap p ears (ab out 2 min), it is safe to remove the c irc uit p ac k.
6. After the TN802B is shut d own, reseat the c irc uit p ac k to restart the 
system.
7. Log in using ctrl alt del
Upgrading IP trunks (R7) to H.323 trunks
If there are existing  IP trunk c onnec tions that you want to up g rad e to H.323 trunk 
c onnec tions, d o the following  step s. Otherwise, g o to ‘‘Upgrade to TN802B (R8)’’ 
on page 6-76
To upg rad e an existing  IP trunk (R7) to an H.323 trunk (R8) req uires first g etting  
IP information from the existing  TN802 b efore up g rad ing the TN802 to TN802B.
1. Click on My Computer > Control Panel > Network
.
2. Click the Protocols
 tab .
3. Select TCP/IP Protocol 
from the list.
4. Click the Properties
 op tion in the Network wind ow. Write d own the IP 
ad d ress, sub net ad d ress, and  g ateway ad d ress shown for ad ap tor [2] 
(see example b elow).
NOTE:
Do not use the ad d resses for ad ap ter [ 1] . 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Adding or Removing Cabinet Hardware 
6-75 Add IP Interface Assembly 
6
5. When d one, c lic k OK, OK
. 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Adding or Removing Cabinet Hardware 
6-76 Add IP Interface Assembly 
6
Upgrade to TN802B (R8)
NOTE:
The upg rad e takes ab out 20 minutes.
1. Insert the flash d isk into the rig ht most slot on the TN802 IP trunk. On the 
monitor, a d ialog  b ox assig ns a d rive letter with the removab le med ia 
d esig nation; the d efault is D:. 
2. Rig ht c lic k on Start > Explore
 to op en the Wind ows NT Exploring  p ane 
and  selec t the d rive letter ind ic ated in step  1.
3. Double-clic k on Medpro 
and  selec t the Setup  ic on.
4. Follow the Install Shield  p roc ed ure to transfer all the nec essary files to the 
TN802 IP Interfac e. 
NOTE:
In the Finish d ialog  b ox, selec t I will restart later
. Do not 
select Restart computer
.
This would  b e a g ood  time to read  the Read me.txt file.
5. Click on Start > Settings > Control Panel > Services
.
6. Select IP Trunk 
and click on Startup
.
NOTE:
Do not c lic k on Start.
7. Under Startup Type, select Disabled
 and  c lic k OK
 to d isab le IP Trunk 
mod e.
NOTE:
If IP trunk and  Med Pro servic es are b oth set to automatic , the 
TN802B d efaults to IP Trunk and  MedPro features c annot be used .
8. Select MedPro 
and c lic k on Startup
.
NOTE:
Do not c lic k on Start.
9. Under Startup Type, select Automatic
 and  c lic k OK
 to enab le Med Pro 
mod e. 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Adding or Removing Cabinet Hardware 
6-77 Add IP Interface Assembly 
6
10. Clic k Start > Shut Down
 and  selec t Restart the computer?
or on the TN802:
Press the rec essed  reset b utton on the fac ep late (see Figure 6-26
) until 
the LCD shows a flashing  MSHUT *
. When the flashing stops and the 
asterisk d isap p ears (ab out 2 min), reseat the c irc uit p ac k to restart the 
system.
or on the SAT:
a. Type busyout board 
UUCSS 
and press En te r .
b. Type reset board
 
UUCSS and  p ress En te r. 
c . Typ e release b oard  
UUCSS and  p ress En te r. 
Onc e the system is c omp letely initialized , the LCD read s MEDPRO *
.
!WARNING:
When c onnec ted  remotely via p c ANYWHERE, only use the 
p c ANYWHERE Restart Host Comp uter button on the toolb ar to 
restart Wind ows NT.
11. Affix the new TN802B lab el to the c irc uit p ac k.
12. Disc onnec t the monitor, keyb oard , and  mouse. 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Adding or Removing Cabinet Hardware 
6-78 Add IP Interface Assembly 
6
Circuit Pack Verification
1. Type change circuit-pack
 and  p ress En te r.
2. Chec k the Cod e c olumn to see if it says DSMAPD or Med Pro.
.
3. To c orrec t it, g o to the entry just above the TN802B that says DSMAPD.
4. Type MEDPRO, and press 
En t e r. Changing  the one entry automatic ally 
c hang es the entry ab ove it. If it is in IP Trunk mode, you g et the following 
error message:
MedPro type requires TN802 with application. Type 
MEDPRO on circuit-packs form.
5. To c omp lete the ad ministration, refer to the 
DEFINITY ECS Release 8 
Network Connec tivity
 b ook.
change circuit-packs                                            Page   1 of   5 
                              CIRCUIT PACKS                                     
        Cabinet: 1                            Carrier: A
                                         Carrier Type: processor        
 Slot Code  Sf Mode   Name               Slot Code  Sf Mode   Name
11: MEDPRO RESERVED-IP
01: TN754  DIGITAL LINE  12: MEDPRO  RESERVED-IP
02: TN758  POOLED MODEM  13: TN802  B  MAPD BOARD
03: TN2144  ANALOG LINE  14: 
04: TN746  B  ANALOG LINE  15: 
05 16:         
06: TN771  C  MAINTENANCE/TEST  
07: TN464  F  DS1 INTERFACE     
08: TN2140  E&M TIE TRUNK     
09: TN767  E  DS1 INTERFACE     
10: TN799  B  CONTROL-LAN       
  # indicates circuit pack conflict.