Lucent Technologies DEFINITY Enterprise Communications Server Release 8.2 Upgrades And Additions Manual

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Multicarrier G2 Universal Module to R8r EPN 
5-73 High Reliability 
5
Resolve Alarms
Examine the alarm log . Resolve any alarms that may exist using  DEFINITY 
Enterp rise Communic ations Server Release 8 Maintenanc e for R8si
. 
Enable Customer Options and Alarm Origination 
to INADS
1. Get the DOSS order number of the upgrade from the project manager and 
ask the reg ional Customer Software Ad ministration to c omp lete the step s 
in the shad ed  b ox. See ‘‘Where to Call for Tec hnic al Sup p ort’’ on p ag e -xx
 
for telep hone numb ers.
NOTE:
As p art of the system reg istration p roc ess, the INADS Datab ase 
Ad ministrator enab les Alarm Orig ination.
2. When ad ministration is c omp leted , log  in as craft
 at the Login:
 prompt.
init login administration:
1. Log in as init
.
2. Type change system-parameters customer-options
 and press 
En te r 
to verify that the c ustomer op tions are p roperly set.
3. Go to sc reen 6, QSIG Op tional Features, and  set the Basic Call 
Setup 
field  to y
 if the customer was using Supplementary Services 
Protoc ol b  or d  on an ISDN-PRI trunk g roup  b efore the up g rad e.
4. Type change system-parameters offer-options
 and  p ress 
En te r.
5. If the Activate Offer
 field  is n
, set it to y 
and press 
Ta b. A warning  
messag e lets you know whether you need  to save translations and  
reb oot to make the c hang e p ermanent.
6. Press 
En t e r to effec t the c hang es or Canc el if there were no c hang es.
7. Contac t the req uester when d one. 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Multicarrier G2 Universal Module to R8r EPN 
5-74 High Reliability 
5
Save Translations
1. Type save translation
 and press En te r to g et up g rad ed  translations onto 
d isk. If the translations were c orrup ted  d uring  the up g rad e, the following  
error message displays when logging in:
!WARNING:
Translation c orrup tion d etec ted ; c all Luc ent Tec hnolog ies d istrib utor 
immed iately.
NOTE:
Th e  save translation
 c ommand c annot func tion if the translation 
c orruption messag e ap p ears.
Back Up Disk
1. Type backup disk
 and  p ress En t e r to backup all changed files.
2. Type test stored-data long
 and press 
En t e r. This instructs the system to 
verify the c onsistenc y of the MSS files (on the d isk and  removab le med ia).
Return Replaced Equipment
Return unused  G2 eq uip ment to Luc ent Tec hnolog ies ac c ord ing  to the 
req uirements outlined  in:
BCS/Material Log istic s, MSL/Attend ed  Stoc king  Loc ations
Method s and Proc ed ures for Basic  Material Returns 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Multicarrier G2 Universal Module to R8r EPN 
5-75 Critical Reliability 
5
Critical Reliability
Upgrade Cabinets
An existing  universal mod ule c ab inet is always up g rad ed  to an EPN. 
Required Hardware
The eq uip ment in Table 5-14 must be on-site before the upgrade begins. To 
plac e a claim for missing equipment, as part of the Streamlined Implementation 
p roc ess, c all “ 1-800-772-5409”  or the numb er p rovided  b y your Luc ent 
Tec hnolog ies rep resentative.
Table 5-14. Required Hardware 
Equipment Description Quantity
PEC 6300-05X Proc essor Port Network 1
J58890AF Exp ansion Control Carrier 1
J58890BB-3 Port Carrier 1
106647985 TN775B Maintenanc e 1
103557294
or
103281788TN776 Exp ansion Interfac e
TN570 Exp ansion Interfac e4 or 12 
1
4 or 12 1,2
1. Use 4 for a c ritic al reliability system with 2 p ort networks or 12 with 3 port networks.
Either 2 or 8 Exp ansion Interfac es (EIs) ship loose with the EPN eq uip ment. The factory
has installed  the other 2 or 4 EIs in the new PPN.
2. Req uired  port network interfaces in a Release 8 system with the op tional p ac ket bus.J58890TO-1 L1 Removab le Med ia 4
H-600-204 G1 ICC 2 
3
3. Req uired  for an EPN in a c ritical reliab ility system.407439975 20-Foot Multi-mod e Fiber Op tic  Cab le 2 or 6 
4
4. Use 4 or 12 if the EPNs and the PPN are remotely loc ated . Assuming  ac cep tab le
lengths, the fib ers previously connecting  an upg raded  G2 universal mod ule (not a
trad itional module) to the G2 TMS have the c orrect transceiver connec tors and  can b e
reused .
106455348
or
1064553639823-A Lightwave Transc eiver
9823-B Lightwave Transc eiver4 or 12 (See Note 1)
4 or 12 (See Note 1)
106689516 TN771D Maintenanc e Test 1 or 2  
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Multicarrier G2 Universal Module to R8r EPN 
5-76 Critical Reliability 
5
Required Tools
The following tools and  items may b e req uired  d uring  the up g rad e:
nHig h-intensity flashlig ht or AC d rop  lig ht
n3/8-inc h flat-b lad e sc rewd river with a 10-inc h shank (minimum)
n5/16-inc h and  1/4-inc h soc kets with a ratc het and  10-inc h extension
nLong -nose p liers to d isc onnec t ground ing  strap s and straig hten 
backplane pins
nStatic -p roof or orig inal c irc uit p ac k p ac kag ing  for transp orting  c irc uit 
packs
nLab els for id entifying  the p ort c irc uit p ac ks and  c ab les attac hed  to the 
rear of c ab inets
nTwelve #12 and  #10 self-tap p ing  sc rews
nFour sp are c arrier g round ing  straps
nWrist ground strap
nRep air kit for b ac kp lane p ins (KS-22876 L2 or eq uivalent)
nOne c op y of eac h of the following  manuals:
— DEFINITY Enterp rise Communic ations Server Release 8 
Maintenanc e for R8r
— DEFINITY Enterp rise Communic ations Server Release 8 
Ad ministrator’s Guid e
Follow Routine Preventive Maintenance
During  the up g rad e, follow routine p reventive maintenanc e p roc ed ures on the 
system to b e up g rad ed . For information ab out the p roc ed ures and  nec essary 
eq uip ment, refer to the “ Preventive Maintenanc e”  sec tion in 
DEFINITY Enterp rise 
Communic ations Server Release 8 Maintenanc e for R8r
.
Label Cables
To make rec onnec ting  the c ab les simp ler and  more reliable, lab el b oth end s of 
the c onnec tor c ables assoc iated with the c arrier to b e removed . 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Multicarrier G2 Universal Module to R8r EPN 
5-77 Critical Reliability 
5
Check Link Status
1. Type display communication-interface links
 and p ress En te r. Write d own 
all enab led  links.
2. Type status link
 
number and  p ress En t e r. Rep eat this step  for all links.
3. Write d own whic h links are in servic e.
Disable TTI
!CAUTION:
If you d o not d isab le the TTI, the translations c an b e c orrup ted .
1. Make sure the ISDN is in servic e. If not, attempt to b usy out and release 
the ISDN D-c hannel/link. This will b ring  the ISDN trunks b ac k into servic e.
2. Type change system-parameters features
 and press 
En t e r. 
3. On the sec ond  sc reen, set the Enabled?
 field  to n
 to p revent the TTI 
feature from ac tivating .
Power Down G2 System
At the power d istribution unit, set the main c irc uit b reaker to OFF.
Install Power-Failure Transfer Ground Wire
!CAUTION:
To avoid  c ontaminating  sing le-p oint g round , d o not c onnec t the g round  wire 
while the system is p owered  up .
1. Connec t 1 end  of a 10 AWG (#25) (2.6 mm2) wire either to pin 49 of the 
c onnec ting b loc k or to p in 49 of the CAP (c ab le ac c ess p anel) assoc iated 
with the p ower-failure transfer p anel.
2. Route the op p osite end  of the wire to an ap p roved  g round  sourc e and  
c onnec t. 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Multicarrier G2 Universal Module to R8r EPN 
5-78 Critical Reliability 
5
Disconnect Cables
1. With the c ab le retainer in front of you and  the p art numb er visib le (4B or 
4C), loc ate the slot that is almost vertic al. This slot is ad jac ent to the p art 
numb er. Insert a flat b lad e sc rewd river with a 1/4-inc h b lad e into the slot 
and  twist. The retainer will snap  op en easily. Remove the c ab le.
2. Disconnect previously labeled c ables assoc iated with the carrier to be 
removed .
3.Behind  a “ DEFINITY style”  c ab inet, remove the b ac k d oors from the 
c ab inet.
4. Behind  a p reviously up graded  c ab inet, remove all of the b ac k panels. 
(Two d ifferent typ es of sc rews hold  the b ac k p anels to the c ab inet. The 
#10 sc rews c an b e removed  with a sc rewd river or a 1/4-inc h soc ket. The 
#12 screws c an be removed with a sc rewdriver or a 5/16-inch soc ket.)
Remove Circuit Packs from Module Control
Carriers A and B
1. To ensure that p ower units in the “ A”  and  “ B”  c arriers are p rop erly 
replaced, label each power unit with its slot number.
2. Disc onnec t the p ower c ords from the p ower units in the “ A”  and  “ B”  
carriers.
3. Remove all c irc uit p ac ks and  p ower units from c arrier “ A.”  Store the c irc uit 
p ac ks in the static -p roof p ac kag ing .
4. Remove all c irc uit p ac ks from c arrier “ B.”  Store the c irc uit p ac ks in the 
static -proof p ac kag ing .
5. Remove the c irc uit p ac k b lanks from slots that d o not c ontain c irc uit 
p acks.
6. Remove the front trim p late from the “ B”  c arrier b y p ulling  it straig ht off. 
Then remove the front trim p late from the “ A”  c arrier.
Remove CURL from Module Control Carrier A
Remove the CFY1 c urrent limiter (CURL) from the p in-field  b loc k marked  “ CURL”  
on the “ A”  c arrier. The CURL will b e reused  in the DEFINITY ECS Release 8 EPN.
NOTE:
Note the p osition of the c omp onents on the left side of the CURL.
NOTE:
Verify that the CURL meets the minimum usab le vintag e req uirements. 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Multicarrier G2 Universal Module to R8r EPN 
5-79 Critical Reliability 
5
Remove Module Control Carriers A and B
1.Remove the TDM/LAN c ab le from b etween the “ A”  and  “ B”  c arriers. See 
Figure 5-23
. This c ab le will b e reused .
2. Disc onnec t 1 end  of the TDM/LAN c ab le (b etween the “ A”  and  “ D”  
c arriers) from the “ A”  c arrier. Leave the other end  c onnec ted  to the “ D”  
c arrier, and  move the c ab le into a p osition so that it will not interfere with 
removing  the “ A”  c arrier.
NOTE:
Note the p osition of the TDM/LAN c ab le b efore d isc onnec ting .
3. Disc onnec t 1 end  of the TDM/LAN c ab le (b etween the “ B”  and  “ C”  
c arriers) from the “ B”  c arrier. Leave the other end  c onnec ted  to the “ C”  
c arrier, and  move the c ab le into a p osition so that it will not interfere with 
removing  the “ B”  c arrier.
!CAUTION:
When removing the TDM/LAN c ab les from a previously up g rad ed  
c arrier, b e c areful that none of the short p iec es of shrink tub ing c ome 
off the 4 c orner p ins of the p in-field  b loc k. Otherwise, when the new 
eq uip ment is c onnec ted, -48 volts c ould  short to g round .
4. Remove and  retain the 8 g round strap s from b etween the “ A”  and  “ B”  
carriers. See Figure 5-24
.
5. Disconnect 1 end of the 8 ground straps from between the “A” and “D”  
c arriers. These strap s will rec onnec t to the new “ A”  c arrier.
6. Disconnect 1 end of the 8 ground straps from between the “B” and “C”  
c arriers. These strap s will rec onnec t to the new “ B”  c arrier.
7. Disc onnec t the “ P1”  (small 9-pin) c onnec tor and  the “ P2”  (larg e 38-p in) 
c onnec tor from the “ A”  c arrier. See Figure 5-25
. Move the c ab les into a 
p osition where they will not interfere with removing  the c arrier.
8. Slid e the latc h up , and  d isc onnec t the “ P1”  (small 9-p in) c onnec tor from 
the “ B”  c arrier. Move the c ab le into a p osition where it will not interfere with 
removing  the c arrier.
9. Disc onnec t and  remove the ICC c ab les. See Figure 5-23
. They will not b e 
reused.
10. Remove the fan trim p late by p ulling  it straig ht off.
11. Clean or rep lac e the air filter (403326820) if nec essary.
12. In front of c arrier, remove the 4 sc rews (top  2 first) hold ing  the “ B”  c arrier 
to the c ab inet frame. Use a long -hand le sc rewd river or 5/16-inc h soc ket 
with a 10-inc h extension.
13. Behind  the c arrier, remove the 2 sc rews hold ing  the “ B”  c arrier’s rear 
c onnec tor p anel to the c ab inet frame. 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Multicarrier G2 Universal Module to R8r EPN 
5-80 Critical Reliability 
5
14. Slid e the c arrier forward  1 to 2 inc hes; then, from the b ac k, b e sure that no 
c ab les or wiring  harnesses are c aug ht on the c ab inet/c arrier framework.
!CAUTION:
Cab les and  wiring harnesses c an be d amag ed  if they c atc h on the 
framework and  if too muc h pressure is ap p lied  in removing  the 
carrier.
15. Remove the c arrier b y slid ing  it out the front of the c ab inet.
16.Rep eat Step s 12 through 15 for the “ A”  c arrier.
17. On p ort c arrier J58890BB-1, c onnec t the TDM c ab le or the TDM 
terminator to Slot 02. On p ort c arriers J58890BB-2 and  J58890BB-3, 
c onnec t the TDM c ab les or the TDM terminator to Slot 01. If the port 
c arrier has J58890BB-1 
and J58890BB-2 p rinted on it, treat it as a 
J58890BB-1. 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Multicarrier G2 Universal Module to R8r EPN 
5-81 Critical Reliability 
5
Figure 5-22. TDM/LAN Connections for Duplicated G2 Universal Module Figure Notes
1.Port Carrier (“ C” Position)
2. ZAHF4 TDM/LAN Terminator
3. TDM/LAN Cab le (WP91716 L6)
4. Mod ule Control Carrier (“ A”  
Po s it io n )
5. Port Carrier (“ D” Position)
6. Port Carrier (“ E”  Position)7. Slot 21
8. Slot 01
9. TDM/LAN Cab le (WP91716 L7)
10. Dup lic ated  Mod ule Control Carrier 
(“ B”  Position)
11. ICCA Cab le (Slot 03)
12. ICCB Cab le 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Multicarrier G2 Universal Module to R8r EPN 
5-82 Critical Reliability 
5
Figure 5-23. Locations of Ground Jumpers Figure Notes
1. Rear of Cab inet
2.Mod ule Control Carrier (“ A”  Position)
3. Exp ansion Mod ule Control Carrier
(“ B”  Position)4. Ground  Jump ers
5. Port Carrier (“ C”  Position)
6. Port Carrier (“ D”  Position)