Lucent Technologies DEFINITY Enterprise Communications Server Release 8.2 Upgrades And Additions Manual

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
G3vs with Intel 386 or Risc Processor to R8r 
4-3 Read This First 
4
Usable Circuit Packs
Every circuit pac k used in the Release 8 system must conform to the minimum 
usab le vintag e req uirements for that system. At a p resale site insp ec tion, the 
remed iation p roc ess c hec ks the vintag es of existing c irc uit p ac ks to b e reused  in 
the Release 8 system. Circ uit p ac ks with unusab le vintag es must b e rep lac ed .
Refer to 
Technical Quarterly, Referenc e Guid e for Circ uit Pac k Vintag es, Chang e 
Notic es, 
and  to the Software Release Letter, for information ab out usab le c irc uit 
p ac k vintages. For information ab out usab le vintages of non-United  States c irc uit 
p ac ks, refer to the ITAC’s Tec h Alert from your reg ional d istrib utor.
Contact Network Technicians
Contac t the tec hnic ian for eac h p ub lic  and  p rivate network ac c essed  b y the 
system b efore the up g rad e b eg ins. Otherwise, it is p ossib le that network-ac c ess 
trunk fac ilities will b e b usied  out at the far end .
Required Tools
The following tools and  items may b e req uired  d uring  the up g rad e:
n1/4-inc h flat b lad e sc rewd river
n1/4-inc h soc ket with ratc het (op tional)
nLong -nose p liers to straig hten b ac kp lane p ins
nStatic -p roof or orig inal c irc uit p ac k p ac kag ing  for transp orting  c irc uit 
packs
nLab els for id entifying  the p ort c irc uit p ac ks and  c ab les attac hed  to the 
rear of c ab inets
nOne d ozen #8 self-tapp ing  sc rews
nRep air kit for b ac kp lane p ins (KS-22876 L2 or eq uivalent)
nOne c op y of eac h of the following  manuals:
— DEFINITY Enterp rise Communic ations Server Release 8 
Maintenanc e for R8r
— DEFINITY Enterp rise Communic ations Server Release 8 
Ad ministrator’s Guid e 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
G3vs with Intel 386 or Risc Processor to R8r 
4-4 Task Tables 
4
Ta s k  Ta b l e s
Table 4-1 p rovid es the hig h-level tasks to perform the up g rad e in this c hap ter.
Table 4-1. Tasks to Upgrade to Release 8r 
ÖTask Description Page
Software Upgrade
4-6
Save Translations and Announcements4-7
Check Link Status4-7
Disable TTI4-8
Disable Alarm Origination to INADS4-8
Shut Down DEFINITY LAN Gateway System 4-8
Shut Down DEFINITY AUDIX System4-9
Power Down Present System4-9
Install Emergency Transfer Ground Wire4-9
Remove the Present System4-10
Unpack and Install the Release 8r Cabinet4-11
Remove Emergency Transfer Ground Wire4-11
Power-Up the Release 8r4-11
List Configuration Software Long4-11
Restore Disk Full4-12
Set Daylight Savings Rules4-12
Set Date and Time4-13
Re-Record Announcements (TN750/B)4-15
Copy Announcements (TN750/B)4-15
Install Remaining Hardware and Administer the System4-16
Enable TTI4-16
Check Link Status4-16
Enable Scheduled Maintenance4-16
Continued on next page 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
G3vs with Intel 386 or Risc Processor to R8r 
4-5 Task Tables 
4
Resolve Alarms4-16
Enable Customer Options and Alarm Origination to INADS4-17
Save Translations4-18
Back Up Disk4-18
Return Replaced Equipment 4-18
Table 4-1. Tasks to Upgrade to Release 8r  — Continued
ÖTask Description Page 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
G3vs with Intel 386 or Risc Processor to R8r 
4-6 Preliminary Procedures 
4
Preliminary Procedures
Software Upgrade
For this up g rad e, a Translation Up g rad e Tool (TUT) is req uired . The translations 
on the translation c ard  must b e c op ied  to tap e. This p roc ed ure must b e 
performed before the upgrade begins.
1. Cop y the translations in the p resent system to a sp are translation c ard . 
Ty p e  save translation
 and press 
En te r. This instruc ts the system to write all 
translation information from memory to the translation c ard .
NOTE:
The off-site STS translation up g rad e d oes not p reserve the c ontent of 
rec orded  announc ements. Therefore, d uring  the up g rad e, any 
announc ements stored  on a TN750/B c irc uit p ac k must b e 
re-rec ord ed . The TN750C Announc ement c irc uit p ac k stores 
announc ements in non-volatile memory; saving the announc ements 
is not need ed .
2. Mail the translation c ard  to Software Tec hnic al Sup p ort (STS) (with 
next-d ay d elivery) to b e c onverted  and  written to a Release 8r removab le 
med ia. This p roc ess takes several d ays. The new Release 8r software 
removab le med ia (inc lud ing  1 with translations) must be on-site b efore the 
up g rad e b eg ins. For eac h Release 8r p roc essor, 2 removab le med ia (1 
system and  1 b ac kup ) must always b e retained  on site with the system.
3. Insert the orig inal translation c ard  b ac k into the p resent system. 
4. If p ossib le, the c ustomer should  p ut a freeze on any new translations while 
the sp are tap e is b eing  c onverted . If not, b e sure the c ustomer’s switc h 
ad ministrator keep s d etailed  rec ord s of any translation c hanges mad e 
d uring that interval. These rec ord s will fac ilitate the reassig nment of any 
c hang es on the Release 8r removab le med ia after the up grad e. 
Follow Routine Preventive Maintenance
During  the up g rad e, follow routine p reventive maintenanc e p roc ed ures on the 
system to b e up g rad ed . For information ab out the p roc ed ures and  nec essary 
eq uip ment, refer to the “ Preventive Maintenanc e”  sec tion in 
DEFINITY Enterp rise 
Communic ations Server Release 8 Maintenanc e for R8r
. 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
G3vs with Intel 386 or Risc Processor to R8r 
4-7 Remove the Present System 
4
Remove the Present System
nIf the eq uip ment room is large enoug h to allow the Release 8r c ab inet to 
b e installed  while the p resent system is in servic e, skip  to ‘‘Install the 
Release 8r Cabinets’’ on page 4-11. Return to this sec tion when finished .
nIf the p resent system must b e removed  to make room for the Release 8r 
c ab inet, p erform the following .
Save Translations and Announcements
1. Log  in at the manag ement terminal on the p resent system.
2. Type save translation
 and press 
En t e r. This c ommand  instructs the system 
to write all translation information from memory to the translation c ard .
3. Chec k for translation errors before p roc eed ing  with the up g rad e. If errors 
are d etec ted , refer to ‘‘No Translations After Upgrade’’
 in Appendix B, 
‘‘Troubleshooting  an Upgrade’’ to c orrec t the p rob lem. Do not c ontinue 
with the up g rad e until the errors are c orrec ted . 
4. If the system c ontains a TN750/B Announc ement c irc uit p ac k, type 
display announcements
 and  p ress 
En t e r. 
NOTE:
The TN750C Announc ement c irc uit p ac k c ontains non-volatile 
memory and  d oes not req uire b ac kup .
5. If administered  rec ord ed  announc ements are listed , typ e save 
announcements
 and  p ress 
En te r.
6. Remove the translation c ard and  install the b ac kup  translation c ard .
Check Link Status
1. Type display communication-interface links
 and p ress En te r. Write d own 
all enab led  links.
2. Type status link
 
number and  p ress En t e r. Rep eat this step  for all links.
3. Write d own whic h links are in servic e. 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
G3vs with Intel 386 or Risc Processor to R8r 
4-8 Remove the Present System 
4
Disable TTI
!CAUTION:
If you d o not d isab le the TTI, the translations c an b e c orrup ted .
1. Make sure the ISDN is in servic e. If not, attempt to b usy out and release 
the ISDN D-c hannel/link. This will b ring  the ISDN trunks b ac k into servic e.
2. Type change system-parameters features
 and press 
En t e r. 
3. On the sec ond  sc reen, set the Enabled?
 field  to n
 to d e-ac tivate the TTI 
feature.
Disable Alarm Origination to INADS
1. Type change system-parameters maintenance
 and press En t e r. 
2. Type neither 
in the Alarm Origination to OSS Numbers 
field .
3. For some releases of software, d isab le Cleared Alarm Notification 
and  Restart Notification
 field before sub mitting  the form.
!CAUTION:
If Alarm Orig ination is not disab led , the system may g enerate alarms, 
resulting  in unnec essary troub le tic kets.
Shut Down DEFINITY LAN Gateway System
!WARNING:
Neg lec ting  to shut d own a DEFINITY LAN Gateway assemb ly b efore 
p owering  d own the system c ab inet c an d amage the LAN Gateway d isk.
1. Log  onto the DEFINITY LAN Gateway. See DEFINITY Communic ations 
System Generic  3 Installation, Ad ministration and  Maintenanc e of 
CallVisor ASAI over the DEFINITY LAN Gateway
 for the p roc ed ure to log  
on.
2. When the main menu ap p ears, selec t 
Maintenanc e.
3. Select 
Reset System from the Maintenanc e menu.
4. Select 
Sh u t d o w n from the Res et Sy ste m menu.
5. Unseat the LAN Gateway assemb ly from its b ac kp lane c onnec tors. 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
G3vs with Intel 386 or Risc Processor to R8r 
4-9 Remove the Present System 
4
Shut Down DEFINITY AUDIX System
!WARNING:
Neg lec ting  to shut d own an AUDIX assemb ly b efore p owering  d own the 
system c ab inet where it resides c an d amage the AUDIX d isk.
1. If a DEFINITY AUDIX System resid es in the system to b e up g rad ed , shut 
d own the AUDIX assemb ly and  allow the d isk to c omp letely sp in d own. 
Refer to ‘‘DEFINITY AUDIX Power Procedures’’ on page 4-19
.
2. Unseat the AUDIX assemb ly from its b ac kp lane c onnec tors.
Power Down Present System
!CAUTION:
Powering  d own the PPN will c ause imp ortant system d ata, suc h as BCMS 
d ata, rec ord s of q ueued ACD c alls, Automatic  Wakeup  req uests, and  Do 
Not Disturb  requests to b e lost. Refer to DEFINITY Enterp rise 
Communic ations Server Release 8 Maintenanc e for R8r, for information 
ab out p rep aring  the system for a p ower d own.
1. At the PPN c ab inet power sup p ly, set the main c irc uit b reaker to OFF.
Install Emergency Transfer Ground Wire
!CAUTION:
To avoid  c ontaminating  single-p oint g round , do not c onnec t the g round  
strap  while the system is p owered  up .
1. Connect a 10 AWG (#25) (2.6 mm2) wire either to pin 49 of the c onnec ting  
b loc k or to p in 49 of the CAP (c ab le ac c ess p anel) assoc iated  with the 
emergenc y transfer p anel.
2. Route the other end  of the wire to an ap p roved  g round  and  c onnec t. 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
G3vs with Intel 386 or Risc Processor to R8r 
4-10 Remove the Present System 
4
Disconnect Power and Ground
1. Disc onnec t the c ab inet p ower c ord s from the rear of the c ab inet.
2. Disconnect the 10 AWG (#25) (2.6 mm
2) c oup led b ond ing  c ond uc tor wire.
3. Disc onnec t the 6 AWG (#40) (4.1 mm
2) CABINET GROUND wire from the 
g round  b ar in the c ab inet.
Remove the Present System
1. Disc onnec t the manag ement terminal from the TERM c onnec tor.
2. Remove all of the 25-pair c ables from the rear of the system. Retain any 
c ab les that c an b e reused  with the Release 8r c ab inet.
3. Remove the AC p ower c ord  from the system.
4. Remove the g round  wires from the system. If the wires c an reac h the 
Release 8r c ab inet, retain them for c onnec tion to the Release 8r system. 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
G3vs with Intel 386 or Risc Processor to R8r 
4-11 Install the Release 8r Cabinets 
4
Install the Release 8r Cabinets
Unpack and Install the Release 8r Cabinet
1. Refer to the installation instruc tions in DEFINITY Enterp rise 
Communic ations Server Release 8 Installation and  Test for Multic arrier 
Cab inets
.
!CAUTION:
Do not p ower up  the Release 8r system.
2. Return to this sec tion when the installation of the Release 8r is c omp leted .
Remove Emergency Transfer Ground Wire
1. If the Release 8r is b eing  installed  while the p resent system is in servic e:
a. Connec t a 10 AWG (#25) (2.6 mm
2) wire either to p in 49 of the 
c onnec ting b loc k or to p in 49 of the CAP (c able ac c ess p anel) 
assoc iated  with the emerg enc y transfer p anel.
b . Route the other end  of the wire to an ap p roved  g round  and  
c onnec t.
2. If the p resent system was removed to make room for the Release 8r 
c ab inet:
a. Disc onnec t the 10 AWG (#25) (2.6 mm
2) wire (installed earlier) from 
the c onnec ting bloc k or pin 49 of the CAP (c ab le ac c ess p anel).
Power-Up the Release 8r
1. Insert the new Release 8r removab le media into the op tic al d rive.
2. Power up  the Release 8r c abinet and  allow the system to b oot up  
c omp letely.
List Configuration Software Long
1. Type list configuration software long 
and  p ress En te r  to verify the 
removab le media c ontains the req uired  Release 8 software.
2. Make note of the entire alp hanumeric  string  of the software version. This 
information is used  later. 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
G3vs with Intel 386 or Risc Processor to R8r 
4-12 Install the Release 8r Cabinets 
4
Restore Disk Full
1. Type restore disk full
 and  p ress En te r. This instruc ts the system to c op y 
the entire removab le med ia to d isk and  takes ab out 30 minutes to 
c omp lete. Release 8 system software with translations are now resid ent on 
the d isk.
NOTE:
Until this c ommand  finishes, the system p rovid es no user feed b ac k 
on the manag ement terminal. Do not p ress 
En te r while the c ommand 
exec utes. Doing  so c auses the terminal sc reen to c lear as the 
c ommand  finishes, erasing  any suc c ess/failure messag es the 
system may provid e.
2. Type upgrade software G3V8r.xx.x.xxx.x 
 and press 
En t e r. This takes 
ab out 15 minutes to c omp lete. For Release 5, this is c all preserving .
3. Login as craft
 at the login:
 prompt.
Set Daylight Savings Rules
You c an set up  to 15 c ustomized d aylig ht saving s time rules. If you have switc hes 
in several d ifferent time zones, you c an set up  rules for eac h. A d aylig ht saving s 
time rule sp ec ifies the exac t time when you want to transition to and  from daylig ht 
saving s time. It also spec ifies the inc rement at whic h to transition. 
NOTE:
The d efault d aylig ht saving s rule is 0
, no d aylig ht saving s.
1. Type change daylight-savings-rules
 and press 
En t e r.
 
DAYLIGHT SAVINGS RULES
Rule Change Day Month___Date Time____Increment
0: No Daylight Savings
1: Start: first Sunday
___ on or after April___ 1  at _2:00 01:00Stop:  first Sunday___ on or after October_ 25 at _2:002: Start: first _________ on or after ____ __ at __:__
Stop:  first _________ on or after ____ __ at __:__
3: Start: first _________ on or after ____ __ at __:__
Stop:  first _________ on or after ____ __ at __:__
4: Start: first _________ on or after ____ __ at __:__
Stop:  first _________ on or after ____ __ at __:__
5: Start: first _________ on or after ____ __ at __:__
Stop:  first _________ on or after ____ __ at __:__
6: Start: first _________ on or after ____ __ at __:__
Stop:  first _________ on or after ____ __ at __:__
7: Start: first _________ on or after ____ __ at __:__
Stop:  first _________ on or after ____ __ at __:__