Lucent Technologies DEFINITY Enterprise Communications Server Release 8.2 Upgrades And Additions Manual

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Adding or Removing Cabinet Hardware 
6-129 Add MCC Port Carriers 
6
Save Translations
1. Log  in at the manag ement terminal.
2. If the system is hig h- or c ritic al-reliab ility, typ e status spe
 and press 
En te r  
to verify that the stand b y SPE is refreshed  and  that the stand b y d isk is in 
servic e.
3. Type save translation [spe-a 
or both] disk
 and press 
En t e r. This 
c ommand  instruc ts the system to take all translation information in 
memory and  write it to the d isk(s).
4. If the MCC p ort network c ontains a TN750 Announc ement c irc uit p ac k, 
type display announcements
 and press 
En t e r.
If administered  rec ord ed  announc ements are listed , typ e list 
configuration software-version
 and  p ress 
En t e r. Chec k sc reen 2 to find  
out when the announc ements were last saved .
Save the c urrent announc ements b y typ ing  save announcements
 and 
p ressing  
En t e r.
5. Type backup disk [spe-a 
or both]
 and  p ress 
En te r. This c ommand  
instruc ts the system to b ac kup  the c urrent information on disk to the 
system tap e(s).
6. Up d ate b ac kup  tape(s), if required .
Shut Down DEFINITY LAN Gateway System
If a DEFINITY LAN Gateway system resid es in the c ontrol c ab inet to b e 
up g rad ed , p rep are to shut d own the DEFINITY LAN Gateway assemb ly and  
allow the disk to c omp letely sp in d own. 
!CAUTION:
Make sure that you save the system p arameters if you p lan to reuse the 
c urrent system.
!WARNING:
Neg lec ting  to shut d own a DEFINITY LAN Gateway assemb ly b efore 
p owering  d own the system c ab inet where it resides c an d amage the LAN 
Gateway d isk.
1. Unseat the LAN Gateway assemb ly from its b ac kp lane c onnec tors in the 
carrier.
2. Log  onto the DEFINITY LAN Gateway. See the
 DEFINITY Communic ations 
System Generic  3 Installation, Ad ministration and  Maintenanc e of 
CallVisor ASAI over the DEFINITY LAN Gateway
.
3. When the main menu ap p ears, selec t 
Maintenanc e.
4. Select 
Reset System from the Maintenanc e menu.
5. Select 
Sh u t d o w n from the Res et Sy ste m menu. 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Adding or Removing Cabinet Hardware 
6-130 Add MCC Port Carriers 
6
Shut Down DEFINITY AUDIX System
1. If a DEFINITY AUDIX resides in the MCC p ort network to b e up g rad ed , 
shut d own the AUDIX assemb ly and  allow the d isk to c ompletely sp in 
d own. Refer to ‘‘DEFINITY AUDIX Power Procedures’’ on page 6-141
.
!WARNING:
Neg lec ting  to shut d own an AUDIX assembly b efore p owering  d own 
the system c ab inet where it resides c an damag e the AUDIX d isk.
2. Unseat the AUDIX assemb ly from its b ac kp lane c onnec tors.
Power Down MCC Port Network
1. At the MCC p ort network, set the main c irc uit b reaker to OFF.
Install Port Carrier
1. Open the rear d oors.
2. Remove the b lank p ort c arrier p anel by pushing  outward  on panel from the 
rear of the c ab inet until the p anel c lears the 4 retaining p ins on the c ab inet 
frame. See Figure 6-49
.
3. Use a sc rewd river to loosen and  remove the 4 retaining  p ins from the 
c ab inet frame.
4. Alig n the c arrier throug h the front of the system c ab inet with the 4 p ilot 
holes on c ab inet frame.
NOTE:
Support the carrier by the molded-in support pins above the top 
mounting  holes.
5. Insert self-tapp ing  sc rews in the p ilot holes and  tighten.
6. Attac h the mag netic ally-held nomenc lature panel to front of c arrier.
7. At the rear, install 8 g round ing  jump ers from the adjac ent b ac kp lane to the 
new c arrier b ac kp lane wiring  (Figure 6-50
 and  Figure 6-51).
8. Connec t a 9-p in D sub miniature p lug  on rig ht sid e of c ab inet to P1 
c onnec tor on c arrier. If nec essary, c ut the tie wrap  holding  the interc ab inet 
c ab le to the up rig ht in the area of the c arrier b eing  installed.
9. Connec t the TDM/LAN c ab le to the newly installed  p ort c arrier. See Figure 
6-52, Figure 6-53, Figure 6-54, or Figure 6-55 and Table 6-11. 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Adding or Removing Cabinet Hardware 
6-131 Add MCC Port Carriers 
6
10. Install a 631AR, 631WA1, 631DA1, or 644A p ower unit in the leftmost slot 
and  a 631BR, 631WB1, 631DB1, 645B, or 649A p ower unit in the 
rig ht-most slot of installed  p ort c arrier as follows:
a. Set the c irc uit b reaker on the p ower unit to be ad d ed  to OFF.
b. Move locking slide on power unit to its leftmost position and open 
the lever.
c . Alig n and  slid e the p ower unit into slot in the c arrier until some 
resistance is felt.
d . Lift the loc king lever upward  until it latc hes.
e. Move the loc king  slid e on p ower unit to its rig htmost p osition.
f. Connec t a p ower c ord  insid e the c ab inet to the outlet on the p ower 
unit.
g . Set the c irc uit b reaker on the p ower unit to ON.
11. Install a TN736 p ower c onverter in the slot next to the 631AR p ower 
c onverter or a TN752 p ower c onverter in the slot next to the 631WA1 
p ower c onverter on the left sid e of the c arrier.
NOTE:
The TN736 is not required  when the 631DB1 p ower unit is used in 
the J58890B-2 or J58890B-3 p ort c arriers. It is req uired  in the 
J58890B-1 p ort c arrier reg ardless of whic h 631 p ower unit is 
p rovid ed . Use the TN752 or TN755B if the system is eq uip p ed  with 
neon messag e waiting .
12. Install the p ort c irc uit p ac ks in the c arrier.
13. Connec t the AC/DC p ower c ord s loc ated  insid e the c ab inet to the p ower 
units.
14. Install the rear p anels around  the p ort c arrier.
15. Install c ab les from the p ort c arrier to the MDF.
16. Install the c ab le ac c ess panel, as req uired .
Reseat DEFINITY LAN Gateway System
1. Reseat the LAN Gateway assemb ly into its b ac kp lane c onnec tors in the 
carrier.
Reseat DEFINITY AUDIX System
1. Reseat the AUDIX assemb ly into its bac kp lane c onnec tors. 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Adding or Removing Cabinet Hardware 
6-132 Add MCC Port Carriers 
6
Power Up MCC Port Network
1. At the MCC p ort network, set the main c irc uit b reaker to ON.
2. The system p erforms a level 4 reb ooting  proc ess, load ing  the system 
p rog ram and  d efault translations from the d isk. Reb ooting  takes 5 to 11 
minutes.
3.Refer to “ Initialization and  Rec overy”  and  “ LED Interp retation”  c hap ters in 
DEFINITY Enterp rise Communic ations Server Release 8 Maintenanc e for 
R8 r
, for c irc uit pac k LED ind ic ations and  manag ement terminal d isplays 
that occ ur during system reboot.
4. After the system reb oot is finished  and  all troub le c leared , verify that the 
EMERGENCY TRANSFER CONTROL switc h is set to AUTO. This restores 
the system to the normal op erating  mod e.
Restart DEFINITY LAN Gateway System
1. Log  onto the DEFINITY LAN Gateway. 
2. When the main menu ap p ears, selec t 
Maintenanc e.
3. Select 
Reset System from the Maintenanc e menu.
4. Select 
Restart System from the Reset System menu.
Enter Added Translations
1. Enter ad ded  translation d ata as ap p lic ab le using  D EFINITY En terp ris e 
Communic ations Server Release 8 Ad ministrator’s Guid e
.
Resolve Alarms and Enable Alarm Origination
1. Examine the alarm log . Resolve any alarms using  DEFINITY Enterp rise 
Communic ations Server Release 8 Maintenanc e for R8r
.
2. If the Alarm Origination Activated
 field  ad ministration is alread y 
set to y
, b e sure to enab le Alarm Orig ination. Otherwise you d o not need  to 
enab le Alarm Orig ination (p roc eed  to the next sec tion).
3. Type change system-parameters maintenance
 and press 
En t e r.
Th e  Alarm Origination Activated
 field  was c hang ed to Alarm 
Origination to OSS Numbers
 to sup p ort more than 1 OSS. 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Adding or Removing Cabinet Hardware 
6-133 Add MCC Port Carriers 
6
4. Type first-only 
in this field  to enab le Alarm Orig ination (to the first OSS, 
which should be INADS).
Be sure to typ e y
 in both Cleared Alarm Notification
 and Restart 
Notification
 field s. Press 
En te r.
NOTE:
The INADS Datab ase Ad ministrator enab les Alarm Orig ination as 
p art of the reg istration proc ess.
!CAUTION:
If you d o not enab le Alarm Orig ination when the c ustomer has 
purc hased a services contract, the switc h will not report any alarm to 
the TSC automatic ally, c ausing  the TSC to b e unab le to fulfill the 
servic es c ontrac t.
Save Translations
1. If the system is hig h- or c ritic al-reliab ility, typ e status spe
 and press En te r  
to verify that the stand b y SPE is refreshed  and  that the stand b y d isk is in 
servic e.
2. Type save translation [spe-a 
or both] disk
 and press 
En t e r. This 
c ommand  instruc ts the system to take all translation information in 
memory and  write it to the d isk(s).
3. If the MCC p ort network c ontains a TN750 Announc ement c irc uit p ac k, 
type list configuration software-version
 and press 
En te r.
If sc reen 2 shows that rec ord ed  announc ements were saved , these 
announc ements c an b e restored  using  the restore announc ements 
command. Type restore announcements 
and  p ress 
En te r.
4. Type backup disk [spe-a 
or both]
 and  p ress 
En te r. This c ommand  
instruc ts the system to b ac kup  the c urrent information on disk to the 
removab le med ia. 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Adding or Removing Cabinet Hardware 
6-134 Add MCC Port Carriers 
6
Update Port-Assignment Records
1.Up d ate the c ustomer’s p ort-assig nment rec ord s.
Figure 6-49. Blank Carrier Panel (Rear View)
Figure 6-50. Locations of Grounding Jumpers (Small Cabinet)
CABINET
FRAME
RETAINING
PINS
PORT CARRIER B
CONTROL CARRIER A
CABINET
REAR VIEW (COVERS REMOVED)FANS
GROUNDING
JUMPER 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Adding or Removing Cabinet Hardware 
6-135 Add MCC Port Carriers 
6
Figure 6-51. Locations of Grounding Jumpers
PORT CARRIER C
PORT CARRIER B
CONTROL CARRIER A
FANS
PORT CARRIER D
PORT CARRIER E
REAR VIEW (COVERS REMOVED)
GROUNDING
JUMPERS
GROUNDING
JUMPERS
CABINET 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Adding or Removing Cabinet Hardware 
6-136 Add MCC Port Carriers 
6
Figure 6-52. TDM/LAN Bus Connections for Standard Reliability R8r PPN
NOTE:
On p ort c arrier J58890BB-1, c onnec t the TDM c ab le or TDM terminator to 
slot 02. On p ort c arriers J58890BB-2 and  J58890BB-3, c onnec t the TMD 
c ab les or TDM terminator to slot 01. If the p ort c arrier has J58890BB-1 and  
J58890BB-2 stenc illed  on it, treat it as a J58890BB-1. Figure Notes
1.Port Carrier (“C” Position)
2. ZAHF4 TDM/LAN Terminator
3. TDM/LAN Cab le (WP91716L6)
4.Process Carrier (“A” Position)
5. Port Carrier (“ D” Position)
6. Port Carrier (“ E”  Position)7. Slot 21
8. Slot 00
9. TDM/LAN Cab le (WP91716L7)
10. Port Carrier (“ B”  Position)
11. Slot TDM/LAN2 (20)
cadf052 KLC 102297
12
2
3
3
4
5
6
7
7
7
7
7
8
9
103 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Adding or Removing Cabinet Hardware 
6-137 Add MCC Port Carriers 
6
Figure 6-53. TDM/LAN Bus Connections for Critical-Reliability PPN
NOTE:
On p ort c arrier J58890BB-1, c onnec t the TDM c ab le or TDM terminator to 
slot 02. On p ort c arriers J58890BB-2 and  J58890BB-3, c onnec t the TMD 
c ab les or TDM terminator to slot 01. If the p ort c arrier has J58890BB-1 and  
J58890BB-2 stenc illed  on it, treat it as a J58890BB-1. Figure Notes
1.Port Carrier (“C” Position)
2. ZAHF4 TDM/LAN Terminator
3. TDM/LAN Cab le (WP91716L6)
4.Process Carrier (“A” Position)
5. Port Carrier (“ D” Position)
6. Port Carrier (“ E”  Position)
7. Slot 218. Slot 00
9. TDM/LAN Cab le (WP91716L7)
10. Process Carrier (“B” Position)
11. ICCD Connec tor
12. ICCC Connec tor
13. Interc arrier Cable D (WP-91954)
14. Interc arrier Cable C (H600-182) 
cadf051 KLC 102297
12
2
3
3
3
4
5
6
7
7
7
7
7
8
8
9
1011
12
13
14 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Adding or Removing Cabinet Hardware 
6-138 Add MCC Port Carriers 
6
Figure 6-54. TDM/LAN Bus Connections for Standard- or High-Reliability 
EPN
CONTROL CARRIER
SLOT 21
B
A
D
PORT CARRIER
PORT CARRIER SLOT 21
PORT CARRIER
TERMINATOR TDM BUS
SLOT 21
E
(ZAHF4)
SLOT 21
C
REAR VIEWPORT CARRIER (ZAHF4)
SLOT 21
EXPANSIONJ58890AF J58890BB
J58890BB
J58890BB
J58890BB SEE NOTE SEE NOTE SEE NOTE SEE NOTE
NOTE:
ON PORT CARRIER J58890BB-1, CONNECT THE TDM CABLE OR TDM TERMINATOR TO SLOT 02.
ON PORT CARRIERS J58890BB-2 AND -3, CONNECT THE TDM CABLES TO SLOT 01.
SLOT 02
TDM/LAN BUS TERMINATOR
TDM/LAN CABLE
WP91716 L6
WP91716 L7 TDM/LAN CABLE
WP91716 L6 TDM/LAN CABLE TDM/LAN CABLE
WP91716 L6