Lucent Technologies DEFINITY Enterprise Communications Server Release 8.2 Upgrades And Additions Manual

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Adding or Removing Cabinet Hardware 
6-59 Add IP Interface Assembly 
6
Connect the Modem
NOTE:
These instruc tions are for c onnec ting  the U.S. Rob otic s modem sup p lied  to 
U.S. c ustomers only. If using  a d ifferent mod em, follow the manufac turer’s 
instruc tions on c onnec ting  the mod em.
1. Connec t the RS232 p ort of the mod em to the MODEM c onnec tor of the 
TN802B external c ab le assembly. 
NOTE:
Chec k the lab els near the c onnec tors; the MODEM and  COM2 
c onnec tors look the same.
2. Connec t an analog  telephone line to the leftmost analog -line p ort on the 
mod em as shown in Figure 6-25
. 
3. Make sure that the mod em’s DIP switc hes are set as shown in 
Figure 6-25
 and  Table 6-7. 
4. Plug  the mod em into an AC p ower outlet.
5. Turn on the mod em using  the switc h on the front of the mod em.
Figure 6-25. External Modem Connections for U.S. Robotics Sporster Figure Notes
1. Connec t analog  line here.
2. DIP switc h 5 must b e up .3. Connec t MODEM c onnec tor here.
4. Connec t p ower c onnec tor here.
12345678
modfrobo KLC 030499
234
1 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Adding or Removing Cabinet Hardware 
6-60 Add IP Interface Assembly 
6
Connect the Monitor, Keyboard, and Mouse
NOTE:
Only make these c onnec tions if ad ministered  loc ally. Not nec essary if 
ad ministered  remotely.
You must c onnec t these b efore inserting  the TN802B IP Interfac e.
1. Attac h a VGA monitor to the VGA c onnec tor of the TN802B IP Interfac e 
external c ab le assemb ly.
2. Attac h the keyb oard  to the KEYBOARD c onnec tor of the external c ab le 
assemb ly.
3. Attach the mouse to the MOUSE connector of the external c able 
assemb ly.
4. Plug  the monitor into an AC p ower rec ep tac le and  turn it on.
Table 6-7. U.S. Robotics Modem Dip Switch Settings
Dip 
Switch Setting Description
1UP
DOWNData Terminal Read y normal
Data Terminal Read y overrid e
2UP
DOWNVe r b a l  r e s u lt  c o d e s
Numeric  result c od es
3UP
DOWNSuppress result codes
Disp lay result cod es
4UP
DOWNEc ho offline c ommand s
No ec ho, offline c ommand s
5UP
DOWNAuto answer on first ring or higher if specified in NVRAM
Auto answer off
6UP
DOWNCarrier d etec t normal
Carrier d etec t overrid e
7UP
DOWNLoad  NVRAM d efaults
Load  fac tory d efaults
8UP
DOWNDumb  mod e
Sm a rt  m o d e 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Adding or Removing Cabinet Hardware 
6-61 Add IP Interface Assembly 
6
Connect the Ethernet
1. Connec t the network c ab le to the ETHERNET c onnec tor on the TN802B 
external c ab le assemb ly.
NOTE:
You need  a CAT5 or better c ab le for 100-Mb yte operation.
Install the Circuit Pack
!CAUTION:
When add ing  or rep lac ing  any hard ware, b e sure to g round  yourself against 
elec trostatic  d isc harg e (ESD) b y wearing  a g round ed  wrist strap .
NOTE:
The TN802B IP Interfac e is hot-swap p ab le, so you d o not need  to p ower 
d own the c arrier to install it.
If you need  to remove the TN802B IP Interfac e from the c arrier at a later 
time, shut down Wind ows NT first b y p ressing the rec essed reset button on 
the fac ep late (see Figure 6-26
) of the TN802B IP Interfac e until the LCD 
shows a flashing MSHUT *
. When the flashing  stop s and  the asterisk 
d isap p ears (ab out 2 min), it is safe to remove the c irc uit p ac k. 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Adding or Removing Cabinet Hardware 
6-62 Add IP Interface Assembly 
6
Figure 6-26. TN802B IP Interface faceplate
NOTE:
To p rop erly seat the c irc uit p ac k, p ush firmly on the front of the fac ep late 
until the latc h reac hes the b ottom rail of the c arrier. Then c lose the latc h 
until it is fully eng ag ed .
1. Insert the TN802B IP Interfac e into the rig htmost of the three slots you 
reserved  for it (see Figure 6-27
).
When you p lug  in the TN802B IP Interfac e, the c irc uit p ac k starts to b oot 
and  the LCD read s PC Boot 
then after ab out 3 to 4 minutes it c hang es to 
IP TRK *
, the default mod e. Figure Notes
1. LCD d isp lay
2. Reset b utton (rec essed )
3. Red  b oard  status LED4. PCMCIA c ard slot
5. Yellow PCMCIA d isk-in-use LED
1
2
3
4
5
fpdfmapd KLC 030899 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Adding or Removing Cabinet Hardware 
6-63 Add IP Interface Assembly 
6
Figure 6-27. J58890MA-1 L30 IP Interface Assembly
Test the Modem
1. Check for dial tone.
2. Contac t Luc ent Tec hnolog ies Customer Sup p ort and  ask a rep resentative 
to d ial into your IP Interfac e server. 
Administer the IP Interface
Ad minstration is d one either loc ally or remotely. If ad ministered  loc ally, p roc eed  
with the following  ad minstration step s on the attac hed  keyb oard , mouse, and  
monitor. If administered  remotely, c all your servic e rep resentative to start the 
p roc ess.
456
789
1
0
1
11
21
3
1
41
51
6
ndfmapd KLC 031299
456
789
1
0
1
11
21
3
1
41
51
6
indfmapd KLC 031299 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Adding or Removing Cabinet Hardware 
6-64 Add IP Interface Assembly 
6
Administration Steps
1. Log in as craft
.
2. Type change circuit-pack
 and  p ress 
En te r.
3. Chec k the Cod e c olumn to see if the slots ab ove the TN802B say 
DSMAPD or MEDPRO.
.
4. If MEDPRO, g o to the entry just ab ove the TN802B that says MEDPRO.
5. Type DSMAPD, and press 
En te r. Chang ing the one entry automatic ally 
c hang es the entry ab ove it. If it is in IP Trunk mode, you g et the following 
error message:
MedPro type requires TN802 with application. Type 
MEDPRO on circuit-packs form.
Log onto the TN802B Interface Server 
If administered  remotely throug h p c ANYWHERE:
1. Dial in to the server through pcANYWHERE using the dialup number 
supplied. 
2. Clic k on the p c ANYWHERE Remote Host Computer b utton on the toolb ar 
to send  
CTRL ALT DEL to the host.
3. Type administrator
 in the User Name
 field .
4. Type iptrunk
 in the Password
 field  and  c lic k OK
. 
5. After log g ing  on for the first time, c hang e the ad ministrator p assword and , 
if d esired , the user name, to ensure sec urity. See your Wind ows NT server 
d oc umentation for d etails.
change circuit-packs                                            Page   1 of   5 
                              CIRCUIT PACKS                                     
        Cabinet: 1                            Carrier: A
                                         Carrier Type: processor        
 Slot Code  Sf Mode   Name               Slot Code  Sf Mode   Name
11: DSMAPD RESERVED-IP
01: TN754  DIGITAL LINE  12: DSMAPD  RESERVED-IP
02: TN758  POOLED MODEM  13: TN802  B  MAPD BOARD
03: TN2144  ANALOG LINE  14: 
04: TN746  B  ANALOG LINE  15: 
05 16:         
06: TN771  C  MAINTENANCE/TEST  
07: TN464  F  DS1 INTERFACE     
08: TN2140  E&M TIE TRUNK     
09: TN767  E  DS1 INTERFACE     
10: TN799  B  CONTROL-LAN       
  # indicates circuit pack conflict. 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Adding or Removing Cabinet Hardware 
6-65 Add IP Interface Assembly 
6
If administered  loc ally on a monitor, keyb oard, and  mouse:
1. Press 
CTRL, ALT, and  DEL simultaneously.
2. Type administrator
 in the User Name
 field .
3. Type iptrunk
 in the Password
 field  and  c lic k OK
. 
4. After log g ing  on for the first time, c hang e the ad ministrator p assword and , 
if d esired , the user name, to ensure sec urity. See your Wind ows NT server 
d oc umentation for d etails.
A-Law versus Mu-Law
For systems using  A-Law c omp and ing , an ad d itional p roc ed ure is nec essary. 
On the SAT:
1. Busyout the trunk g roup  assoc iated  with the IP trunk b y typing  busyout 
board 
UUCSS and  p ressing  En t e r.
In the Wind ows interfac e to TN802B:
1. Click on Control Panel > Services.
2. Highlight IP Trunk Service
, then c lic k on Stop
.
3. In the lower left-hand  c orner, rig ht-c lic k Start >  Exp lore.
4. Go to the c : d rive and  c lic k on its, then b in.
5. Double-c lic k on the its.ini file to op en it in Notep ad .
6. Und er the [ Med iaLib ]  sec tion, g o to COMPANDING= MLAW. Chang e 
MLAW
 to ALAW
.
7. Click on File > Save
 to save the file.
8. Click on File > Exit
 to exit Notep ad .
9. Click on Control Panel > Services.
10. Highlight IP Trunk Service
, then c lic k on Start
.
NOTE:
Do not selec t Startup .
After servic e has started , g o to the SAT:
1. Release the trunk g roup  assoc iated  with the IP trunk b y typing  release 
board
 
UUCSS and  p ressing  En t e r. 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Adding or Removing Cabinet Hardware 
6-66 Add IP Interface Assembly 
6
Assign Server and Domain Names
The Windows NT server identifies servers using a server name plus a domain 
name that loc ates the named  server in a p artic ular p art of the network. The 
TN802B IP Interfac e is ship p ed  with generic  server and  d omain names. Assig n 
rep lac ement names that are meaning ful within your network. 
1. Click on My Computer > Control Panel > Network
.
2. Selec t the Identification
 tab , then c lic k Change
.
3. Typ e the new server name in the Computer Name 
field .
4. Typ e the new d omain name in the Domain
 field and  c lic k OK > OK > 
Close
.
5. When p romp ted  to reb oot the c omp uter, selec t one of the following  
op tions:
nNo
 if you have not assig ned  IP ad dresses then g o to ‘‘Assign an IP 
Address’’
nYe s
 if you have assigned  IP ad dresses. 
Assign an IP Address
1. Click on My Computer > Control Panel > Network
.
2. Click the Protocols
 tab .
3. Select TCP/IP Protocol 
from the list.
4. Click the Properties
 op tion in the Network wind ow.  
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Adding or Removing Cabinet Hardware 
6-67 Add IP Interface Assembly 
6
5. Verify that the Adapter
 drop  d own menu lists 2 DEC Ethernet ad ap ters.
!CAUTION:
Do not c hange any setting s on the ad ap ter lab eled  [ 1]  for any 
reason.
6. Selec t the DEC Ethernet ad ap ter lab eled  [ 2] . 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Adding or Removing Cabinet Hardware 
6-68 Add IP Interface Assembly 
6
7. Typ e a valid  IP ad d ress for the IP Interfac e server in the IP Address:
 
field .
8. Typ e the ap p rop riate sub net mask in the Subnet Mask:
 field. 
NOTE:
Not all networks req uire step s 9 throug h 18. Chec k with the loc al 
network ad ministrator to determine whic h are req uired .
9. If you use g ateways, type the IP ad d ress of the d efault g ateway for the IP 
Interfac e server in the Default Gateway:
 field.
10. Clic k on the DNS tab  and  verify that the d omain DNS server is c orrec t.