Lucent Technologies DEFINITY Enterprise Communications Server Release 8.2 Upgrades And Additions Manual

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Adding or Removing Cabinet Hardware 
6-39 Remove an EPN Cabinet from an Existing System 
6
All Installations
1. When the system reset is finished, type status port-network 2
 and press 
En t e r. The Port Network Status sc reen ap p ears. Verify that PNC Ac tive is 
“ up ”  and that the Servic e State is “ in.”  
2. A Span LED, on the front of the DS1 Converter circuit pack, must be off for 
eac h inac tive fac ility administered . For examp le, if Fac ility A and  Fac ility B 
are unad ministered , then the top  2 Sp an LEDs on the c irc uit p ac k must b e 
off. If the yellow LEDs are on, then p rob lems were enc ountered d uring the 
unad ministration of hard ware. Sp an LEDs assoc iated  with ad ministered  
fac ilities (C and  D, in this examp le) should  b e on.
Removing the Hardware
1. Be sure that you have unad ministered  the trunks, attend ant c onsoles, 
voic e terminals, and  d ata mod ules assoc iated  with the p ort c irc uit pac ks 
in the EPN c ab inet. 
2. Remove the fib er op tic  c ab les from the fib er transc eivers at b oth end s of 
the fib er sp an. Carefully c oil the fib er op tic  c ables. Avoid  b end ing  c ab les 
to a rad ius smaller than 1.5 inc hes (3.8 c m).
3. Remove the fib er transc eivers from the DS1 and /or DS1 c onverter c irc uit 
p ac ks at b oth end s of eac h fib er sp an.
4. Remove the 25-p air c ab les from the c onnec tor p anel on eac h c arrier of 
the EPN. 
5. Type remove cabinet 
  and  p ress 
En t e r. This removes the EPN 
c ab inet ad ministration.
6. Remove the p ower c ord s from the p ower units in eac h c arrier in the EPN 
and  remove the AC power c ord  or DC p ower wires.
7. Chec k the ground ing  sc heme for the c ab inets. Perform the following :
a. If any c ab inet ground  wires c onnec t in 
series b etween the EPN 
c ab inet and  any other c ab inet, remove the wires from the EPN 
c ab inet and  c onnec t them to the next c abinet in the g round  p lane. 
!CAUTION:
Never leave c ab inets ungrounded . When a ground  wire is 
removed  from a series-c onnec ted  c abinet, the g round  p lane 
b ec omes op en with respec t to all sub seq uent c ab inets.
b . If any c abinet g round  wires c onnec t in parallel to other c ab inets, or 
c onnec t d irec tly to the AC p ower panel g round  or other ap proved  
g round , remove the wire from eac h end  of the g round sp an.
8. Carefully remove the EPN c ab inet. The c ab inet may weig h as muc h as 
800 p ound s. Use c aution. 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Adding or Removing Cabinet Hardware 
6-40 Remove an EPN Cabinet from an Existing System 
6
9. Type change system-parameters features
 and  p ress En t e r. Use this 
sc reen to c hang e the TTI field b ac k to its p revious value b efore the 
up g rad e.
10. When finished , p lac e d ust c overs over all exp osed  fib er c oup ling s that 
remain after the fib er op tic  c ab les are removed .
11. If any fib er op tic  c ab les were removed  from Lightg uide Interc onnec t Units 
(LIUs) or Fib er Patc h Panels, remove the assoc iated  c able lab eling . This 
will prevent c onfusion if existing  fib er is later moved.
12. Return all unused equipment (not owned by the customer) to Lucent 
Tec hnolog ies ac c ord ing  to the req uirements outlined in:
BCS/Material Log istic s, MSL/Attend ed  Stoc king  Loc ations
Method s and Proc ed ures for Basic  Material Returns
Troubleshooting 
Message Waiting Lamps On
This usually means that all affec ted  p ort-related  translations were not 
unad ministered .
1. Type clear amw all 
  and  press 
En te r. This c lears the messag e 
waiting  lamp  for the sp ec ified  extension.
2. Rep eat the c ommand  for eac h extension with a lit messag e waiting  lamp. 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Adding or Removing Cabinet Hardware 
6-41 Add External Modem to EPN 
6
Add External Modem to EPN
U.S. Robotics Model USR 33.6 EXT External 
Modem
Figure 6-18. Connect External Modem to EPN
1. Connec t an RS-232 c ab le to the modem. See Figure 6-18
.
NOTE:
In the following  step s, a PC with Wind ows 95 or Wind ows NT 4.0 may 
b e sub stituted for the d umb  terminal. Use the Hyp erterminal 
(terminal emulation) ap p lic ation. 
2. Connec t the op p osite end  of the RS-232 c ab le to a d umb  terminal. 
3. Set the d umb  terminal to full d up lex mod e.
4. Type AT&N6
 to set the baud  rate to 9600. 
NOTE:
The mod em c onnec ts at 9600 b aud  b ut throug hp ut is at 1200 b aud .
5. Type AT & W 0
 to save the setting  into non-volatile RAM.
6. Set Switc h 5 to the OFF (up ) p osition to disab le auto answer.
7. Disc onnec t the RS-232 c ab le from the terminal and c onnec t it to the 
TERMINAL c onnec tor on the rear of the system c ab inet. Figure Notes:
1. U.S. Rob otic s External Mod em
2. RS-232 Cab le
3. Exp ansion Port Network
cydfepnm KLC 100397
TERM INAL
1
2
3 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Adding or Removing Cabinet Hardware 
6-42 Add DCS Interface 
6
Add DCS Interface
Systems in a Distrib uted  Communic ations System (DCS) network are 
interc onnec ted b y b oth tie trunks (for voic e c ommunic ations) and  d ata links (for 
c ontrol and  transp arent feature information). These d ata links, also c alled  DCS 
sig naling  links, supp ort the feature transp arenc y. 
Various sub sets (dep end ing  on the sp ec ific  c onfig uration) of DS1 Interfac e 
c irc uit p ac ks (inc lud ing TN464F, TN767E, and  TN760E) p rovide the 
voic e-c ommunic ations interfac e.
Meanwhile, the d ata link interfac e (b etween the p roc essor and  the p hysic al 
sig naling  link) is p rovid ed  b y (or throug h) a TN799 Control-LAN c irc uit p ac k. In 
some c onfig urations, the TN799 passes the sig naling  information over a sep arate 
10BaseT TCP/IP network (usually via a hub ). For use with 10BaseT, c onnec t the 
ap p rop riate p ins of the I/O field  to the hub . For p inouts and  d iagrams, refer to the 
installation manual for your c ab inet typ e. In other c onfigurations, the TN799 
c irc uit p ac k c arries sig naling  over p oint-to-p oint p rotoc ol (PPP) for subseq uent 
inc lusion (via the switc hing  fab ric ) in the same DS1 b it stream as the DCS voic e 
transmissions.
A TN780 Tone-Cloc k c irc uit p ac k (installed  in the PPN) c an interfac e external 
Stratum 3 sync hronization for DS1 c onnec tions.
For further information about DCS, refer to the following  d oc uments:
nAT&T System 75/85 Network and Data Servic es Reference Manual
nSystem 75 Ap p lic ation Notes Network Servic es
nDEFINITY ECS Release 8 Ad ministration for Network Connec tivity
Add Circuit Packs
A TN 4 6 4 F,  TN 7 6 7 E,  o r  TN 7 6 0 E D S1  c irc u i t  p a c k  i s re q u ire d  f o r  PPP c onnec tions. 
A TN799 Control-LAN c irc uit p ac k is also req uired.
1. Determine the p ort assig nments of the c irc uit p ac ks to b e ad d ed . If there 
are no availab le p ort slots in the p roc essor c ab inet for the Control-LAN 
c irc uit p ac k, p lac e it in a R8 EPN c ab inet p ort slot. You d o not need  to 
p ower d own the c ab inet to install the c irc uit p ac k.  
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Adding or Removing Cabinet Hardware 
6-43 Add DCS Interface 
6
Install Cables
1. Install c ab le from the c ab inet to a hub  or 110 (p urp le) wall field  as 
req uired. Connec t the 259A c onnec tor to the p ort slot c ontaining the 
Control-LAN circuit pac k. See Figure 6-19
. For a p inout of TN799, see 
Table 6-3
. 
Figure 6-19. Cable Connection for Control-LAN Figure Notes
1. 259A Connec tor
2. DW8A Cable3. Hub  or 110 (Purp le) Wall Field
1
2
3cydflan2  EWS 101398 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Adding or Removing Cabinet Hardware 
6-44 Add DCS Interface 
6
Enter Added Translations
1. Get the DOSS order numb er of the upg rad e. Call the reg ional CSA to 
p erform the step s in this sec tion.
2. To enab le DCS, set the DCS
 field  on the System Parameters-Customer 
Options sc reen to y
.
3. Ad minister the other req uired  translation data using  the forms listed  und er 
Distrib uted  Communic ations System (DCS) in 
DEFINITY Communic ations 
System Administration for Network Connec tivity
.
Save Translations
1. If the system is hig h- or c ritic al-reliab ility, typ e status spe
 and press En te r  
to verify that the stand b y SPE is refreshed  and  that the stand b y d isk is in 
servic e.
2. Enter save translation [spe-a or both] disk
 and  p ress 
En t e r. This 
c ommand  instruc ts the system to take all translation information in 
memory and  write it to the d isk(s).
Table 6-3. TN799 Pinout
Backplane Pin 25-Pair Wire Color Lead NamePeripheral 
Connector Pin
103 White/Orang e TD+ 27
003 Orange/White TD- 2
104 White/Green RD+ 28
004 Green/White RD- 3 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Adding or Removing Cabinet Hardware 
6-45 Add IP Interface Assembly 
6
Add IP Interface Assembly
DEFINITY ECS IP Solutions allows you to send  voic e and  fax from the DEFINITY 
ECS throug h an Internet p rotoc ol (IP) network to other DEFINITY ECSs having  
this feature or to other H.323 V2 c omp liant end p oints. It is imp lemented  using  the 
TN802/B IP Interfac e, whic h is a Wind ows NT server resid ing  on the IP Interfac e 
Assemb ly insid e the DEFINITY ECS.
The IP Interfac e is an assemb ly c omp osed  of a TN802B c irc uit b oard, a 
p roc essor c ard , and DSP resourc e c ard . For ord ering  p urp oses, the assemb ly is 
id entified  as a J58890MA-1 L30, b ut for simp lic ity, we refer to it in this b ook as the 
TN802B IP Interfac e.
The TN802B IP Interfac e op erates in two mod es: IP Trunk, availab le with Release 
7 or later, and  Med ia Proc essor (Med Pro), availab le with Release 8. The IP Trunk 
mod e is Internet Telep hone Server—Enterp rise (ITS-E) c omp atib le, and  the 
Med Pro mod e is H.323 V2 c omp atib le. The TN802B IP Interfac e is b ac kward s 
c omp atib le and  d efaults to IP Trunk mod e.You must ad minister it to use it in 
Med Pro mod e.
For more information on the IP Interfac e c ap ab ilities and  limitations, refer to the 
DEFINITY Enterp rise Communic ations Server Release 8 Overview.
The following sec tions d esc rib e the proc ess for
nInstalling in Media Processor Mode
nInstalling in IP Trunk Mode
nUpgrading a TN802 V3 (or later) to a TN802B (MedPro mode)
!WARNING:
When c onnec ted  remotely via p c ANYWHERE, only use the p c ANYWHERE 
Restart Host Computer b utton on the toolb ar to restart Wind ows NT.
Installing in Media Processor Mode
To operate in Med Pro mod e, you must install the TN802B IP Interfac e and , if the 
system d oes not have one, you must also install and  administer a TN799B
 C-LAN 
c irc uit p ac k. For C-LAN administration, refer to 
DEFINITY Enterprise 
Communic ations Server Ad ministration for Network Connec tivity.
If you have existing  TN802 IP Interfac e c irc uit p ac ks, you c an up g rad e them 
either b y rep lac ing  the c irc uit p ac k with a TN802B or b y d ownload ing  the 
TN802B firmware onto the c irc uit p ac ks (see ‘‘Upgrade to TN802B (R8)’’ on page 
6-76).  
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Adding or Removing Cabinet Hardware 
6-46 Add IP Interface Assembly 
6
Prepare for Installation
Have the following  eq uip ment on site b efore your ship ment arrives:
nAC p ower outlets for the mod em and  monitor.
nThree unoc c up ied  and  ad joining  p ort slots in the DEFINITY ECS for the 
TN802B IP Interfac e, if need ed.
The TN802B oc c up ies only one slot, b ut it need s the two slots to its left for 
c learanc e.
nAn ad d itional unoc c up ied  p ort slot for the TN799B, if need ed . If you have 
an existing TN799 c irc uit p ac k, rep lac e it with the TN799B.
nA 10 BaseT or 10/100 BaseT Ethernet c onnec tion into your loc al area 
network for the TN802B.
nA 10 BaseT Ethernet c onnec tion into your loc al area network for the 
TN799B.
nTwo or more valid , unused  IP ad d resses on your network (one for MedPro 
and  one for C-LAN) that c an b e assig ned  to the IP Interfac e server. You 
also need  the subnet mask and  d efault g ateway. 
nAn analog telep hone line reserved  (DID is okay) for the IP Interfac e 
diagnostic modem 
nA valid  telep hone numb er reserved  for the IP Interfac e d iag nostic  mod em 
In ad dition if non-U.S. c ustomer:
nMod em c omp arab le to a U.S. Rob otic s Sportster Mod el USR 33.6 EXT.
nCable from modem to TN802B external c able assembly.
We rec ommend  that you p rotec t your c ab inet with an uninterrup tib le power 
system (UPS).
Check your Shipment
When your DEFINITY ECS ord er arrives at your site, c hec k the c ontents (see 
Table 6-4
).
1. Insp ec t the ship p ing  c arton for d amag e b efore op ening  it. If the b ox is 
damaged, 
do not open it. Inform the ship p ing  c omp any, and  ask for 
instruc tions on filing a c laim.
2. If the b ox is und amag ed , c hec k the c ontents ag ainst the p ac king  slip . 
Chec k the c ondition of eac h c omp onent, and note any d amag e or 
shortag es on the p ac king  slip . The c arton should  c ontain the following  for 
eac h IP Interfac e ord ered : 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Adding or Removing Cabinet Hardware 
6-47 Add IP Interface Assembly 
6
3. Read  and  follow any d irec tions inserted  into the p ac kag e b y the fac tory.
The TN802B external c ab le assemb ly is a bund le of c ab les with an amp henol 
c onnec tor at the end  of the b und le and  various PC-typ e c onnec tors (VGA, 
Universal Serial Bus [ USB] , mouse, keyb oard , Ethernet, mod em, and  COM2) at 
the end s of the ind ivid ual c ab les. See Fig ure 6-20
. Look for the lab el where the 
b und le enters the amp henol c onnec tor. 
Table 6-4. Required Hardware
Comcode/Code Description Quantity
108525528 TN799B C-LAN c irc uit p ac k. One 
TN799B sup p orts more than one 
TN802B.1
J58890MA-1 L30 TN802B IP Interfac e Assemb ly
1 or more
601939804 H600-512,G1 external c ab le assemb ly 1 or more
259A c onnec tor 1
CAT5 or b etter c able 1
407633999 U.S. Robotic s Sp ortster external 
modem, Model USR 33.6 EXT (U.S. 
customers only). Non-U.S. customers 
must p rovid e a mod em c omp arab le to 
this mod el.1
601087091 20-ft DB-25 serial c ab le from mod em 
to TN802B external c ab le assembly 
(U.S. c ustomers only). Non-U.S. 
c ustomers must p rovid e a serial c ab le.1 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Adding or Removing Cabinet Hardware 
6-48 Add IP Interface Assembly 
6
Figure 6-20. TN802B IP Interface External Cable Assembly
Connect the Cables
1. Determine into whic h p ort slots you are p utting the TN799B C-LAN and  
TN802B IP Interfac e c irc uit p ac ks.
NOTE:
Make sure that at least 3 ad jac ent slots are free for the TN802B.
From the rear of the c ab inet:
2. If add ing  a new TN799B, c onnec t the 259A c onnec tor to the b ac kp lane 
c onnec tor c orrespond ing  to the TN799B slot.
3. If add ing  a new TN799B, c onnec t one end  of the DW8 c able to the 259A 
c onnec tor. Connec t the other end  to the c ustomer’s network.
4. Connec t the amp henol c onnec tor on the external c ab le assemb ly to the 
b ac kp lane c onnec tor c orresp ond ing  to the TN802B slot (the hig hest 
numb ered c onnec tor of the 3 slots req uired ) Figure Notes
1. Amp henol c onnec tor to c onnec tor 
c orresp ond ing  to TN802B slot
2. To VGA monitor
3. To USB (not used )
4. To keyb oard5. To mouse
6. To ethernet
7. 25-p in male c onnec tor to mod em
8. 25-p in male c onnec tor to COM2 
cbdfocto AWF 122398
2
1
345678