Lucent Technologies DEFINITY Enterprise Communications Server Release 8.2 Upgrades And Additions Manual

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Upgrading R5si/R6si to R8r EPN and Adding Memory 
3-29 Release 5/6si to Release 8r 
3
For 2 Collocated Expansion Port Networks
1. Behind  p ort c arrier D of the multic arrier PPN:
a. Install a lig htwave transc eiver on the c onnec tor at slot 1D02.
NOTE:
Attenuators may be required for single mode fiber using a 
300A Lightwave Transc eiver
b . Connec t 1 end  of the ap p rop riate fib er op tic  c ab le to the lig htwave 
transc eiver at slot 1D02.
c.Route the c ab le to the c ab inet’s c ab le tray and  d own, out of the 
c ab inet, to the EPN stac k.
d . Carefully attac h the fib er op tic  c ab le (with c ab le ties) to the wall of 
the c ab le tray at the b uilt-in c ab le tie p ositions.
2. Behind control cabinet A of EPN stack 3:
a. Install a lig htwave transc eiver on the c onnec tor at slot 3A01.
NOTE:
Attenuators may be required for single mode fiber using a 
300A Lightwave Transc eiver
b . Connec t the other end  of the fiber op tic  c able from the PPN to the 
lig htwave transc eiver at slot 3A01.
c . Carefully attac h the fib er op tic  c ab le (with c ab le ties) to the rear 
c overs of the EPN stac k.
d . Coil the surp lus fib er optic  c ab le and  p lac e it either in the c ab le 
manag er or on the b ottom shelf (hold ing  the p ower supp ly) of the 
PPN  c a b i n e t .
3. Behind control cabinet A of EPN stack 2:
a. Install a lig htwave transc eiver on the c onnec tor at slot 2A02.
NOTE:
Attenuators may be required for single mode fiber using a 
300A Lightwave Transc eiver
b . Connec t a fib er op tic  c ab le to the transc eiver just installed .
c . Route the c ab le d own the outsid e of the rear c overs to the other 
EPN stack.
d . Carefully attac h the fib er op tic  c ab le (with c ab le ties) to the rear 
c overs of the EPN stac k. 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Upgrading R5si/R6si to R8r EPN and Adding Memory 
3-30 Release 5/6si to Release 8r 
3
4. Behind control cabinet A of EPN stack 3:
a. Install a lig htwave transc eiver on the c onnec tor at slot 3A02.
NOTE:
Attenuators may be required for single mode fiber using a 
300A Lightwave Transc eiver
b . Connec t the other end  of the fiber op tic  c able from the PPN to the 
lig htwave transc eiver at slot 3A02.
c . Carefully attac h the fib er op tic  c ab le (with c ab le ties) to the rear 
c overs of the EPN stac k.
d . Coil the surplus fiber op tic  c ab le and  attac h it (with a c ab le tie) to a 
leg of an EPN c ab le c lamp .
Figure 3-9. High Reliability Release 8r with 2 or 3 Port NetworksFigure Notes
1. Cabinet 1 PPN
2. Cabinet Stac k 2 EPN 13. Cab inet Stac k 3 EPN 2 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Upgrading R5si/R6si to R8r EPN and Adding Memory 
3-31 Release 5/6si to Release 8r 
3
Figure 3-10. Fiber Optic Connections PPN to EPN1
For 1 or 2 Fiber-Remoted Expansion Port Networks
1. Behind  p ort c arrier C of the multic arrier PPN. See Figure 3-9 and Figure 
3-11:
a. Install a lig htwave transc eiver on the c onnec tor at slot 1C02.
NOTE:
Attenuators may be required for single mode fiber using a 
300A Lightwave Transc eiver
b . Connec t a fib er op tic  c ab le to the transc eiver just installed .
c . Route the fib er c ab le to the c ab inet c ab le tray and  out of the 
c ab inet throug h the c ab le manag er to the PDS c ross-c onnec t 
fac ility.
d . Connec t the fib er c ab le to the lig htg uid e interfac e unit p rovided .
e. Carefully attac h the fib er op tic  c ab le (with c ab le ties) to the wall of 
the c ab le tray at the b uilt-in c ab le tie p ositions. Figure Notes
1. Lightwave Transc eiver
2. To PPN Carrier C Slot 1C02
3. To EPN 1 Carrier A Slot 2A01 
(Cab inet Stac k 2)4. Fiber Optic Cable
5. TX Connec tor
6. RX Connec tor
cydff05 CJL 103196
RX TX
2211 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Upgrading R5si/R6si to R8r EPN and Adding Memory 
3-32 Release 5/6si to Release 8r 
3
2. Behind control cabinet A of EPN stack 2:
a. Install a lig htwave transc eiver on the c onnec tor at slot 2A01.
NOTE:
Attenuators may be required for single mode fiber using a 
300A Lightwave Transc eiver
b . Connec t a fib er c able to the transc eiver just installed .
c . Route the fib er c ab le d own the outsid e of the rear c overs and  
throug h the c ab le manag er to the PDS c ross-c onnec t fac ility.
d . Connec t the fib er c ab le to the lig htg uid e interfac e unit p rovided .
e. Carefully attac h the fib er op tic  c ab le (with c ab le ties) to the rear 
c overs of the EPN stac k.
f. Coil the surplus fib er optic  c ab le and  plac e it in the c ab le manag er.
Figure 3-11. Fiber Optic Connections PPN to EPN1 Figure Notes
1. Lightwave Transc eiver
2. To PPN Carrier B Slot 1C02
3. To EPN 1 Carrier A Slot 2A01 
(Cab inet Stac k 2)
4. Fiber Optic Cable5. Fib er Op tic  Cross-Connec t Fac ility
6. Lig htg uid e Interfac e Unit (LIU)
7. TX Connec tor
8. RX Connec tor
cydf013 CJL102396
RX TX
2
22 1
11
22
11 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Upgrading R5si/R6si to R8r EPN and Adding Memory 
3-33 Release 5/6si to Release 8r 
3
Interconnect Port Networks with Fiber Cabling —
Critical Reliability Release 8r
1. Keep  trac k of whic h fib er attac hes to whic h c onnec tor on eac h lig htwave 
transc eiver. This sec tion p rovid es fig ures showing  typ ic al ways of making  
these connec tions.
The c onnec tors on the lightwave transc eivers are lab eled  “ TX”  (transmit) or “ RX”  
(rec eive), while the fib ers attac hing  to eac h c onnec tor are numb ered  “ 1”  or “ 2.” ’ 
See Figure 3-13
.
Collocated Port Networks
For a c ritic al reliab ility system with 1 c olloc ated  exp ansion p ort network, use 2 
fib er op tic  c ab les and 4 lig htwave transc eivers to d irec tly c onnec t the networks. 
For a c ritic al reliab ility system with 2 c olloc ated  exp ansion p ort networks, use 6 
fib er op tic  c ab les and  12 lig htwave transc eivers to d irec tly c onnec t the networks.
NOTE:
Based  on floor p lan c onsid erations, the leng th of these c ab les may vary. 
20-foot (6.1 m) c ab les are normally ad eq uate for a Release 8r with 2 p ort 
networks.
For c olloc ated  c ab inets, route the fib er op tic  c ab les d irec tly from the PPN to eac h 
EPN c ab inet. Sinc e a Release 8r PPN c ab inet is c olloc ated  with a Sing le-Carrier 
Cab inet stac k, the p referred  routing  is to run the c ab les 
down the c ab le tray and  
out the b ottom of the PPN c ab inet. The c ab les are then run to the EPN c ab inet 
and  up  the outsid e of the rear p anels to the d esired  c arrier level.
Fiber-Remoted Port Networks
For a c ritic al reliab ility system with 1 fib er-remoted  EPN, use 4 fib er op tic  c ab les, 
4 lig htwave transc eivers, and  4 lig htguid e interfac e units (p rovid ed  b y the PSC).
For a c ritic al reliab ility system with 2 fib er-remoted  EPN, use 12 fib er optic  
c ab les, 12 lig htwave transc eivers, and  12 lig htg uid e interfac e units (p rovided  b y 
the PSC). 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Upgrading R5si/R6si to R8r EPN and Adding Memory 
3-34 Release 5/6si to Release 8r 
3
DS1 CONV-Remoted Port Networks
For a c ritic al reliab ility system with 1 DS1 CONV-remoted  EPN, this arrang ement 
req uires:
nFour DS1 CONV c irc uit p ac ks (TN1654)
nFour DS1 CONV-to-EI c ab les (847245750 and/or 847245768)
nFour H-600-348 c ab les
nTwo, 4, 6, or 8 p airs of c hannel servic e units (CSUs)
nTwo, 4, 6, or 8 p airs of wall-field  c ab les (p rovid ed  with the CSUs)
n5, 10, or 15 d B attenuators (sing le-mod e fib er only). 
For a c ritic al reliab ility system with 2 DS1 CONV-remoted  EPNs, this arrangement 
req uires:
n12 DS1 CONV c irc uit p ac ks (TN1654)
n12 DS1 CONV-to-EI c ab les (847245750 and/or 847245768)
n12 H-600-348 c ab les
n6, 12, 18, or 24 pairs of CSUs
n6, 12, 18, or 24 p airs of wall-field  c ab les (provid ed  with CSUs)
n5, 10, or 15 d B attenuators (sing le-mod e fib er only). 5d B Attenuator 106060718
10d B Attenuator 106060734
15d B Attenuator  106061021
5d B Attenuator 106060718
10d B Attenuator 106060734
15d B Attenuator  106061021 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Upgrading R5si/R6si to R8r EPN and Adding Memory 
3-35 Release 5/6si to Release 8r 
3
For 1 or 2 Collocated Expansion Port Networks
1. Behind  p ort c arrier C of the multic arrier PPN. See Figure 3-12 and  Figure 
3-13:
a. Install a lig htwave transc eiver on the c onnec tor at slot 1C02.
NOTE:
Attenuators may be required for single mode fiber using a 
300A Lightwave Transc eiver
b . Connec t 1 end  of the ap p rop riate fib er op tic  c ab le to the lig htwave 
transc eiver just installed .
c . Route the fib er optic  c ab le from the lig htwave transc eiver to the 
c ab inet’s c ab le tray and  d own, out of the c ab inet, to the EPN stac k.
d . Carefully attac h the fib er op tic  c ab le (with c ab le ties) to the wall of 
the c ab le tray at the b uilt-in c ab le tie p ositions.
2. Behind  p ort c ab inet B of EPN stac k 2:
a. Install a lig htwave transc eiver on the c onnec tor at slot 2B02.
NOTE:
Attenuators may be required for single mode fiber using a 
300A Lightwave Transc eiver
b . Connec t the other end  of the fib er op tic  c ab le c oming  from the PPN 
to the lig htwave transc eiver just installed .
c . Carefully attac h the fib er op tic  c ab le (with c ab le ties) to the rear 
c overs of the EPN stac k.
d . Coil the surp lus fib er c ab le and  plac e it either in the c able manag er 
or on the b ottom shelf (hold ing  the p ower sup p ly) of the PPN 
c ab inet.
3. Behind  p ort c arrier D of the multic arrier PPN:
a. Install a lig htwave transc eiver on the c onnec tor at slot 1D02.
NOTE:
Attenuators may be required for single mode fiber using a 
300A Lightwave Transc eiver
b . Connec t a fib er op tic  c ab le to the transc eiver just installed .
c . Route the fib er c ab le to the c ab inet’s c ab le tray and  d own, out of 
the c ab inet, to the EPN stac k.
d . Carefully attac h the fib er op tic  c ab le (with c ab le ties) to the wall of 
the c ab le tray at the b uilt-in c ab le tie p ositions. 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Upgrading R5si/R6si to R8r EPN and Adding Memory 
3-36 Release 5/6si to Release 8r 
3
4. Behind control cabinet A of EPN stack 2:
a. Install a lig htwave transc eiver on the c onnec tor at slot 2A01.
NOTE:
Attenuators may be required for single mode fiber using a 
300A Lightwave Transc eiver
b . Connec t the other end  of the fib er op tic  c ab le c oming  from the PPN 
to the lig htwave transc eiver at slot 2A01.
c . Carefully attac h the fib er op tic  c ab le (with c ab le ties) to the rear 
c overs of the EPN stac k.
d . Coil the surp lus fib er c ab le and  plac e it in the c able manag er or on 
the b ottom shelf (hold ing  the p ower sup p ly) of the PPN c ab inet.
Figure 3-12. Critical Reliability Release 8r with 2 or 3 Port Networks Figure Notes
1. Cabinet 1 PPN
2. Cabinet Stac k 2 EPN 13. Cab inet Stac k 3 EPN 2 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Upgrading R5si/R6si to R8r EPN and Adding Memory 
3-37 Release 5/6si to Release 8r 
3
Figure 3-13. Fiber Optic Connections PPN to EPN1 Figure Notes
1. Lightwave Transc eiver
2. To PPN Carrier D Slot 1D02
3. To EPN 1 Carrier A Slot 2A01 
(Cab inet Stac k 2)
4. PPN Carrier C Slot 1C025. EPN1 Cab inet B Slot 2B02
6. Fiber Optic Cable
7. TX Connec tor
8. RX Connec tor
cydff06 CJL 103196
RX
RXTX
TX
4
24
2 3
13
1 
						

							DEFINITY Enterprise Communications Server Release 8.2
Upgrades and Additions for R8r  555-233-115  Issue 1
April 2000
Upgrading R5si/R6si to R8r EPN and Adding Memory 
3-38 Release 5/6si to Release 8r 
3
Switch-Connected Port Networks
For 1 to 15 Standard Reliability EPNs. 
1. Behind  the PPN c ab inet. See Figure 3-14
:
a. Install a lig htwave transc eiver on c ab le c onnec tor at slot 1E02.
b . Install a lig htwave transc eiver on c ab le c onnec tor at slot 1B02.
c . Connec t 1 end  of the metallic  interc arrier c ab le to the lig htwave 
transc eiver at slot 1E02.
d . Route the interc arrier c ab le from the lig htwave transc eiver to the 
c ab inet c ab le tray and  up ward  to c arrier ‘‘B.
e. Connec t the other end  of the interc arrier c ab le to the lig htwave 
transc eiver at slot 1B02.
f. Attac h the interc arrier c able (with c ab le ties) to the wall of the c ab le 
tray at the b uilt-in c ab le tie p ositions.
2. Behind switc h node carrier E of PPN c abinet 1. See Figure 3-14
:
a. For eac h EPN, install 1 lig htwave transc eiver on a c ab le c onnec tor 
with the following  ord er of slots: 1E20, 1E03, 1E19, 1E04, 1E18, 
1E05, and so forth.
b . Connec t 1 end  of eac h fiber op tic  c able to eac h lig htwave 
transc eiver, just installed .
c . Carefully attac h the fib er optic  c ab les (with c ab le ties) to the wall of 
the c ab le tray at the b uilt-in c ab le tie p ositions.
3. Behind  c ontrol c ab inet A of eac h sing le-c arrier EPN:
a. Install a lig htwave transc eiver on c ab le c onnec tor at slot A01.
b . Connec t the other end  of the fiber op tic  c able to the lig htwave 
transc eiver, just installed , at slot A01.
c . Carefully attac h the fib er op tic  c ab le (with c ab le ties) to the rear 
c overs of the EPN stac k.
d . Coil up  the surp lus leng th of fib er op tic  c ab le, and  p lac e the c oil 
either in the c ab le manag er or on the b ottom shelf (hold ing  the 
p ower sup p ly) of the PPN c ab inet.