Home > Vodavi > Communications System > Vodavi Starplus Triad S Description Manual

Vodavi Starplus Triad S Description Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Vodavi Starplus Triad S Description Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 60 Vodavi manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    Page
    of 710
    							System Parameters Programming
    Programmable Flash Rates2-49
    system configuration to desired flash rates. By default, Line Queue Button flash rate is set for a Red 480 ipm
    Flutter (08).
    .-i
    e”$,$ Do Not Disturb Button
    Programming Steps
    1Press the DND BTN flexible button (FLASH 07, button #18). The following message
    displays:
    I
    DND.BTN00-28
    RED STEADY ON
    I
    2Enter a 2-digit value on the dial pad to correspond to one of the 29 available options.
    Refer to flash rate table.
    3Press HOLD to save the entry. A confirmation tone is heard and the display updates.
    Description
    The Do Not Disturb Button flash rate is the rate at which your Do Not Disturb button flashes when you place
    your station in a Do Not Disturb mode. This flash rate can be programmed to 
    29 different options identified
    in the flash rate table. This enables the programmer to customize the key system configuration to desired
    flash rates. By default, Do Not Disturb Button flash rate is set for Red Steady On 
    (01).
    Intercom Hold Button
    Programming Steps
    1Press the ICM HOLD BTN flexible button (FLASH 07, button #19). The following
    message displays:
    ICM HOLD BTN00-28
    RED 15 IPM FLASH
    2Enter a 2-digit value on the dial pad to correspond to one of the 29 available options.
    Refer to flash rate table.
    3Press HOLD to save the entry. A confirmation tone is heard and the display updates.
    STARPLUS Triad-S System Programming Manual
    Issue I - December 1998 
    						
    							System Parameters Programming
    System Parameters Programming
    Description
    The Intercom Hold Button flash rate is the rate at which your Hold button flashes when you receive an
    intercom call and your station’s intercom mode selector switch is in the Tposition. This flash rate can be
    programmed to 
    29 different options identified in the flash rate table. This enables the programmer to
    customize the key system configuration to desired flash rates. By default, Intercom Hold Button flash rate is
    set for a Red 
    15 ipm Flash (09).
    System Parameters Programming
    Programming Steps
    If the system is in the programming mode, continue using the program codes. If starting to program here,
    enter the programming mode.
    1Press FLASH and dial [09]. The following message displays:
    SYSTEM PARAMETERS
    ENTER BUTTON NUMBERIssue I- December 1998
    STARPLUS Triad-S System Programming Manual 
    						
    							. . .._
    System Parameters Programming
    System Parameters Programming
    Description
    This section describes the procedures and steps necessary to program System Parameters in the System
    Parameters programming area. The buttons on the digital terminal are illustrated below:
    LEADING DIGIT 1LEADING DIGIT 2 LEADING DIGIT 3 LEADING DIGIT 4
    9kn 012*13#mLEADING DIGIT 5 LEADING DIGIT 6 LEADING DIGIT 7
    LEA;FA;LplT
    %n%1_6%m *!xzil
    CENTREX
    DIGITS4 DIGIT VM ID
    s- *Llirizl*- *EizxzlMUSIC CH 
    #3MUSIC CH #4MUSIC CH #5MUSIC CH #6
    +#knIllQ %sm*nMUSIC CH 
    #7MUSIC CH #8
    *m88118 *a#130
    STARPLUS Triad-S System Programming ManualIssue I- December 1998 
    						
    							2-52System Parameters Programming
    System Parameters Programming
    Program
    CodeFLASH 09T-Flex
    Button
    1
    2
    3
    4
    5
    6
    7
    8
    9
    10
    11
    12
    13
    14
    15
    16
    17
    18
    Feature
    Leading Digit 1Leading Digit
    Leading Digit 2None
    Leading Digit 3None
    Leading Digit 4None
    Leading Digit 5None
    Leading Digit 6None
    Leading Digit 7None
    Leading Digit OptionDisabled
    Centrex Digits4 digits
    Four Digit Voice Mail ID3 digits
    Music Channel 
    #3*##Music Channel 
    #4*##Music Channel 
    #5*##Music Channel 
    #6*##Music Channel 
    #7*##Music Channel 
    #8*##
    Default
    (after initialization)
    * Music Channels 3-8 can only be used for Music-On-Hold functions
    Table 2-7: System Parameters Programming
    Leading Digit Translation
    Programming Steps
    IPress FLASH and dial [09]. The following message displays:
    .
    LEADING DIGIT 1D-8
    LEADING DIGIT
    2The top left button in the flexible button field is lit for programming Leading Digit 1. To
    change Leading Digits or enter a different Leading Digit, press the appropriate flexible
    button 1-8 and perform the following procedures.
    sEnter a l-digit value on the dial pad that corresponds to the leading digit translation.
    [0] = NONE
    [I] = Trunk Group 1 (81)
    Issue I- December 1998
    STARPLUS Triad-S System Programming Manual 
    						
    							System Parameters Programming
    System Parameters Programming2-53
    [2] = Trunk Group 2 (82)
    [3] = Trunk Group 3 (83)
    [4] = Trunk Group 4 (84)
    [5] = Trunk Group 5 (85)
    [6] = Trunk Group 6 (86)
    [7] = Trunk Group 7 (87)
    [8] = Leading Digit*
    * 8 is unavailable on button 7 (digit 
    7), only O-7 are available.
    4Press HOLD to save the entry. A confirmation tone is heard and the LCD indicates the
    change.
    Description
    This feature lets the system have the dialing plan modified to accommodate multiple systems connected
    together via CO lines. The dialing plan is changed to a four digit access with a programmable leading digit. 
    All
    feature access codes and station numbers are dialed by dialing the programmable leading digit first followed
    by the standard dialing plan. There is no default for this feature.
    _’Conditions:
    +The leading digit does not apply to feature access codes starting with 8,9, or 0.
    -+The remaining digits selected for the Triad-S system may be used as CO line group access for Centrex
    dialing applications.
    Leading Digit EnableProgramming Steps
    1Press the LEADING DIGIT ENABLE flexible button (FLASH 09, button #8). The
    following message displays:
    .
    LEADING DIGIT OPTIONO-lDISABLED2Enter a l-digit value (O-l) that corresponds with the following entries:
    [0] = Disabled
    [I] = Enabled
    3Press HOLD to save the entry. A confirmation tone is heard.
    STARPLUS Triad-S System Programming ManualIssue I- December 1998 
    						
    							2-54System Parameters Programming
    System Parameters Programming
    Description
    This feature enables/disables the Leading digit Integration feature option on a system-wide basis. By
    default, this feature is disabled.
    Centrex Digit Length
    Programming Steps
    1Press the CENTREX DIGITS flexible button (FLASH 09. button #9). The following
    message displays:
    CENT;EX DIGITS4-5
    2Enter a l-digit value (4-5) that corresponds with the following entries:
    [4] = Centrex Digit length
    [5] = Centrex Digit length
    3Press HOLD to save the entry. A confirmation tone is heard.
    Description
    This feature determines the number of Centrex digits in the system.
    Four-Digit Voicemail ID
    Programming Steps
    1Press the FOUR DIGIT VM ID flexible button (FLASH 09, button #lo). The following
    message displays:
    VM ID DIGITS3-43
    2Enter a l-digit entry (3-4) that corresponds to the number of digits to be dialed.
    JPress HOLD to save the entry. A confirmation tone is heard.
    Issue I- December 7998STARPLUS Triad-S System Programming Manual
    ,,c .*,. ,. _:. .’I.y:
    						
    							System Parameters Programming2-55
    System Parameters Programming
    Description
    This feature modifies the station and CO voice mail identification fields such that the maximum length of
    these fields is increased from three digits to four digits. When using leading digit for voice mail 
    IDS, the new
    number must be entered individually... 
    2100,2101,2103, etc. This is performed in Flash 50, Page B, Button
    13.
    MOH Assignments
    Programming Steps
    1Press the MUSIC CH # flexible button (FLASH 09, button #I3 through #18). Thefollowing message displays:
    MUSIC CHANNEL XW,OOl-012
    YYYl
    Where:
    X= 3-8YYY = CO Line number
    T!Enter a 2-digit entry (001-012) that corresponds to the CO line number desired.
    3Press HOLD to save the entry. A confirmation tone is heard.
    Description
    This feature enables the system to assign CO line circuits as additional 6 music-on-hold inputs. This
    increases the capacity of music channels beyond the 2 available on the MISU board for use by MOH sources.
    A total of 8 channels are available for use on the system. By default, no channels are assigned.
    Attendant Station Assignment
    Programming Steps
    iPress FLASH and dial [IO]. The following message displays:
    ATNDl;;A&SI$MENT, 
    9
    zEnter up to 3-digit station number(s) on the dial pad.
    3100-l 31 for Triad-S.
    STARPLUS Triad-S System Programming Manualissue I- December 1998 
    						
    							2-56System Parameters Programming
    System Parameters Programming
    4Press HOLD to save the entry. A confirmation tone is heard and the display updates.
    Description
    The system identifies an attendant station for the purpose of receiving recalls and activating night service.
    The system can have up to three attendant(s) programmed. Entering 
    [#] three times removes that
    attendant assignment or different station numbers can be programmed. By default, Station 100 is assigned
    as the first attendant.
    System Time and Date
    Programming Steps
    To set the time and date that appears on display Terminals:
    1Press FLASH and dial [ll]. The following message displays:
    DATE AND TIME
    MMM DD YYHH:MM am
    2Choose display format by pressing the appropriate button in the flexible button field.
    3Press HOLD or dial the time and date as follows (12 digits):
    YYMMDDHHMMSS
    _------4Press HOLD to save the entry. A confirmation tone is heard and the display updates.
    The time can be displayed in the standard 12 hour format or the 24 hour format.
    12/24 HOUR
    By default, the time is set for 12 hour display format. When entering the time and date, use the following
    data:
    LED Off = 12 Hour Display
    LED On = 24 Hour DisplayThe Date and Time can be changed or set by the first Attendant station
    using dial code 
    [692].
    hue I- December 1998S JARPLUS Triad-S System Programming Manual 
    						
    							System Parameters Programming
    System Parameters Programming2-57
    PBX Dialing Codes
    Programming Steps
    1Press FLASH and dial [12]. The following message displays:
    PBX DIAL CODES
    w, H, w, w, ##.
    zEnter five 2-digit code numbers, one right after the other, on the dial pad up to ten digits.
    If a single digit code is required, enter the code followed by 
    [#I.
    3Press HOLD to save the entry. A confirmation tone is heard and the display updates.
    4To delete a code, enter [#I] [#I and press HOLD.
    Description
    Five l- or Z-digit PBX access codes can be programmed into memory. When dialed, these codes signal the
    system so toll restriction is applied at the next dialed digit. When a single digit code 
    [9] is entered, it must be
    followed by 
    [#I as the second digit. To delete an entry, enter [#I twice and Press HOLD. Lines must be
    programmed as PBX lines before these codes apply. By default, no PBX dialing codes are assigned. This
    programming is performed in Flash 
    40, Page A, Button 2.
    Executive / Secretary Pairs
    Programming Steps
    1Press FLASH and dial [13]. The following message displays:
    I
    EXEC SECY PAIRINGS
    *,mPAIR 1IThe first button is lit indicating the first pair may be programmed.
    2Enter the 3-digit Executive station number.
    3Enter the 3-digit Secretary station number.
    4Press HOLD to save the data. A confirmation tone is heard and the display updates.
    piTo program a second pair, press the second flexible button in the flexible button field and
    enter station numbers as in steps 3-5.
    6To program a third pair, press the third button in the flexible button field and enter station
    numbers as in steps 3-5.
    STARPLUS Triad-S System Programming Manualissue I - December 1998 
    						
    							2-58System Parameters Programming
    System Parameters Programming7To program a fourth pair, press the fourth button in the flexible button field and enter
    station numbers as in steps 3-5.
    Description
    There are four Executive/Secretary pairs available. When an Executive station is busy or in DND, intercom
    calls and transfers are automatically routed to the designated Secretary.EXEC 
    / SECYEXEC / SECYEXEC / SECYEXEC / SECY
    PAIR 
    #lPAIR #2PAIR #3PAIR #4
    I II 4s 12 * 13 48 I4
    The assigned secretary may Camp-On to the Executive Station when the station is busy or in Do-Not-
    Disturb. There can be only one pairing of stations, with no duplicates. You cannot pair Executive 100 to
    Secretary 101, then pair Secretary 101 to Executive 100. The same Secretary station can be specified for
    more than one Executive station (101-105 and 102-105). Entering 
    [#] six times removes the assignments.
    Individual pairs may be changed by pressing the associated flexible button. By default, no Executive 
    /
    Secretary pairs are assigned.
    On-Board Relay Programming
    Programming Steps
    1Press FLASH and dial [14]. button #I is lit to indicate Relay #I is selected. The following
    message displays:
    I
    RELAY X TYPE
    YYYYYYYYYYYY
    IWhere:
    X=1-6
    YYYYYYYYYYYY = Ext Page Zone l-l, 
    LBC Sta XXX, Ran Start X, CO Control XX
    zPress the button that corresponds to the desired relay. That button lights. Enter one of
    the following sequences on the keypad:
    [l]+[l] External Page Zones
    [2]+[1 through 8]= RAN Start
    (RAN Announcement Tables 1-8)
    [3] + STA # = Loud Bell
    [4] + CO # = CO Line Control
    STARPLUS Triad-S System Programming ManualIssue I- December 1998 
    						
    All Vodavi manuals Comments (0)

    Related Manuals for Vodavi Starplus Triad S Description Manual