Home > Vodavi > Communications System > Vodavi Starplus Triad S Description Manual

Vodavi Starplus Triad S Description Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Vodavi Starplus Triad S Description Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 60 Vodavi manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    Page
    of 710
    							Figure 2-10: STARPLUS Triad-S CSIB Board with MSGU Mounted
    Each CKIB or CSIB has 3 loop start CO line interfaces. The loop start CO/PBX lines are connected to RJ-11
    connectors on the right side of each board.
    This completes the 
    CKIB/CSIB installation.
    CKIB/CSIB Wiring
    There is one 50-pin female amphenol connector on the left side of the board. This enables the system to be
    cabled to the main distribution frame 
    (MDF). A 25-pair telephone cable must be prepared with mating
    connectors to extend the interface circuits to the MDF. The cables should be routed through the cable clamps
    at the bottom of the KSU to the MDF. These cables are terminated on industry standard 
    66MI-50 type punch
    down blocks. It is recommended that 
    66MI-50 split blocks with bridging clips be used to simplify
    troubleshooting and to quickly isolate any faults.
    STARPLUS Triad-S Installation Manual
    Lnll5llmlmlml5llml~lIssue I- December 1998 
    						
    							 I_..:Issue I- December 7998
    k!iwlllsll~Iulml~l~L
    STARPLUS Triad-S Installation Manual 
    						
    							Table 2-2: CKIBESIB Wiring
    Wiring for External Page, MOH/BGM, and Relay Is available onlyat the first boardposition of the 
    BKSU.
    S JARPLUS Triad-S /nsta/lation Manual
    lslrl5lllsw5llmlmlmlml
    issue I- December 1998 
    						
    							:::. .-2-20
    Installation
    Station Wiring
    Station Wiring
    The following provides details on the interconnection of each type station interface board and station jack.
    Only the first pair (green, red) on the jack should be connected
    to the 
    KSU. No other pairs should be connected., 
    .I, -.,,.....\,. ..-...I_..* ,:. _...: .” 2 :
    Digital Keyset
    Wiring from the CKIB to the station jack requires single pair cable (2 or 3 pair is recommended). Digitized
    voice, signaling and battery are sent over this pair.
    I@Y BK@
    Figure 2-11: STARPLUS Triad-S Digital Station Jack Wiring
    Single Line Telephone
    The CSIB is wired to SLT devices with single pair cabling to provide talk battery, voice and signaling to and
    from the SLT.
    vr (GREEN)
    VR (RED)
    -f,G R
    Figure 2-12: STARPLUS Triad-S Single Line Telephone WiringIssue I- December 1998
    t!5llisll~il5lll5lll5lll5ll~L
    STARPLUS Triad-S lnstallafion Manual 
    						
    							Installation
    Wall Mounting the Digital Key Telephone
    2-21
    Wall Mounting the Digital Key Telephone
    To wall mount the digital key telephone, it is necessary to use the wall mount bracket and a standard type
    -Y1’1 : ^
    6“L?
    jack designed for 630-type wall hanging applications. See Figure 2-13: Digital Kq Telephone Wall
    Mounting on the following page.
    I
    2
    3
    4
    5
    6
    /
    \“I
    8
    9Remove the handset from the cradle and locate the plastic retainer in the bottom of the
    hook-switch well area.
    Push the plastic retainer slowly upward until it is free.
    Locate the tab on the plastic retainer, making sure it is toward you, then place it back into
    its holder.Slide the plastic retainer all the way down into its channel. Part of the retainer remains
    above its holder to hold the handset secure for the wall mount configuration.
    Turn the telephone over and unplug the line cord. If the cord is not plugged into the wall
    jack assembly, reroute the line cord through the access channel on the top of the
    telephone. If the line cord is plugged into the wall jack assembly, run the line cord through
    the hole provided and plug it into the connector on the back of the telephone.
    Line up the hooks on the top and bottom of the wall mount bracket so they can engage
    with the slots cut into the bottom of the telephone base. Insert the bottom hooks first.
    Slide the mounting bracket slowly downwards until the top tabs slide into the top slots.
    and snap into place.
    Match the two key hole slots on the base plate with the lugs on the 630-A type jack and
    align the modular connector, then slide the telephone into place.
    Place the handset onto the retainer.
    STARPLUS Triad-S hstallation Manual
    ~lurllli;llurll~ll5lllN!zli
    Issue I- December 1998 
    						
    							Mounting Bracket Tabs
    Wall Mounting Holes
    Figure 2-13: Digital Key Telephone Wall Mounting
    The telephone is now ready to use.Issue I- December 1998
    kal~~m~~~~~~~w~1
    STARPLUS Triad-S hstallation Manual
    /; ‘,.,-...--., . .j .-._ .i .._.... ._
    :.71 :. ‘4. .-- 
    						
    							Installation
    Headset Installation2-23
    Headset Installation
    The STARPLUS Triad-S digital key telephones were designed to operate with industry standard electret mic
    compatible modular headset adapters and operator headsets.
    To modify a 
    STARPLUS Triad-S digital key telephone to support an external headset:
    1Plug the headset adapter cord into the vacant handset jack on the key telephone base.
    2Plug the telephone handset cord into the headset adapter box where indicated by the
    headset manufacturer’s instructions.
    Refer to Station Programming in the System Programming manual for instructions on enabling headset
    operation. After programming, the station can enable or disable headset mode by dialing a code, When
    headset mode is active at the station, the ON/OFF button controls the on-hook or off-hook status.
    Additionally, while headset mode is active, features such as on-hook dialing and hands free speakerphone
    operation become inoperable.
    Caller ID Interface Unit Installation
    The Caller Identification Interface Unit receives the data from the telephone company and sends the data, in
    ASCII 
    RS-23X format to the KSU.
    To connect the cable port 
    (9081-00) :
    1Select the correct RS-232 cable.
    2Connect one end of the cable on the desired 
    MSIB I/O port (1 or 2).
    3Connect the other end to the 1480-00 
    l/O port marked RS232.
    Figure Z-14:Caller ID Cable Connections illustrates the connections for the TCI Caller ID Interface Unit,
    Triad-S MISU
    KSU O-Pin1480-00 O-Pin
    Female
    Male
    r--l32
    Figure 2-14: Caller ID Cable Connections
    hllnlml1nlmlml~lml
    STARPLUS Triad-S hsfdafion bkm./a/Issue I- December 7998 
    						
    							Switch Settings
    Sl dip switches select the signaling protocol of the RS-232 OUT connector to assist in matching signals from
    the 
    1480-00 with those of the DTE device. S2 dip switches control two major functions:
    9Switches l-5 configure the 1480-00 to the DTE device for baud rate, data bits, and parity,
    oSwitches 6-S select the unit number for the 1480-00 when multiple units are connected in series, If
    a single unit is used, switches 
    6-8 are set for Unit # 1,
    Set the switches on the 1480-00 as follows:12345678
    12345678
    Programming Caller ID
    ICLID Enable
    1Verify the programming for ICLID enable, +4+%3226, Flash 56.
    2Press Button [I].
    3Dial [I ] on the keypad and press HOLD.
    I/O Ports
    1Verify the programming for the I/O ports, +M3226, Flash 15.
    2Select the I/O port, Button 1, 2 (SIUI, SIU2).
    3Dial [5] on the keypad and press HOLD to select 2400 baud.
    CO Lines
    iVerify the programing for the CO lines, WK3226, Flash 40.
    2Enter the CO line range for the Caller ID Unit.
    3 Press HOLD.
    4Press Button [21] (Page C).
    5Press Button [2], ring delay timer.
    6Enter 04 (minimum) and press HOLD.
    7Reset the system and Caller ID Unit.
    ..I .L _.. _ :i1 . _...-\ “.Issue I- December 1998
    l!ifikll~lmlwl~lml~~
    STARPLUS Triad-S lnstallafion Manual 
    						
    							SMDRThe SMDR feature provides detailed records of all outgoing and/or incoming, long distance only or all calls,
    The SMDR Qualification Timer determines the time needed to determine a valid SMDR call for reporting
    purposes. By default, this timer is set to 30 seconds and is variable from 
    00-60 seconds in one second
    increments. This feature is enabled or disabled in system programming. By default, SMDR is disabled and set
    to record long distance calls only. A printout format of 80 characters maximum or 30 characters maximum
    may be selected in system programming. The standard format is 80 characters per line. A 30 character
    format generates three lines per message. If the SMDR feature is enabled, the system starts collecting
    information about the call as soon as it starts and terminates when the call ends. If the call was longer than
    30 seconds, the following information is printed (see next two pages) :
    STARPLUS Triad-S installation Manual
    l5lllslll!illmll5llmlml~i
    issue 7 - December 1998 
    						
    							30 character format selected:
    123456789L23456789il23456789iAAA BB HH:MM:SS HH:MM MM/DD/YY(CR)(LF)HCCCCCCCCCCCCCCC;;W;CCC;;K;cR>GGGGGGGGGGGGSTA CO TOTAL
    116 08 
    0O:OZ:OO 14:13 05/11/90(CR)(Lt-)0123456789012345678901234(CR~~LF)123456789012(CR)(LF)
    80 character format selected:123456789~123456789~123456789~123456789~123456789~123456789~123456789~123456789~
    AAA BB HH:MM:SS 
    ;;Hz;: MM;;;;YY W;CCCCCCCCCCCCCCCCCCC GGGGGGGGGGGG (CR)(LF)STA CO TOTAL
    ACCOUNT CODE< 
    >< XOST116 08 0O:OZ:OO 14:13 05/11/90 0123456789012345678901234 123456789012(ER)TLF)
    80 character format with Call Cost Displav feature enabled:
    -4123456789~123456789~~23456789~1234567890123456789~123456789~123456789~123456789~
    AAA BB HH:MM:SS 
    ;;Wly MM;;;;YY K;f;;CCCCCCCCCCCCCCCCCCC GGGGGGGGGGGG (CR)(LF)STA CO TOTAL
    116 08 
    0O:OZ:OO 14:13 05/11/90 0123456789012345678901234ACCOUNT CODE+>COST
    123456789012000.0O(CR)(LF)
    BO character format for DISA Calls:
    123456789~123456789~123456789~123456789~123456789~1234567B9~123456789~123456789~4A BB HH:MM:SS W&l MM;;K&YY tW;;CCCCCCCCCCCCCCCCCCC GGGGGGGGGGGG (CR)(LF)STA CO TOTAL340100:02:0014:1305/11/90I CODE+>+~COSTACCOUNT310400:04:5414:1505/11/9010123456789012345678901234 123456789012~~~000.00(CR)(LF)
    ICLID 30 character format selected:
    123456789h23456789;1234567B9;STA CO TOTALSTART
    DATE
    100 01 00:00:19 09:32 10/24/94(CR)(LF)1 602.443-6000(CR)(LF)123456789012**(CR)(LF)
    _ _ _ .  . .-.-_.F .-. .  .‘:=; -
    Table 2-3: SMDR Printoutissue I- December 1998
    l5lllslllrll~lisnl~l~l~~
    STARPLUS Triad-S installation Manual 
    						
    All Vodavi manuals Comments (0)

    Related Manuals for Vodavi Starplus Triad S Description Manual