Vodavi Starplus Triad S Description Manual

							System Parameters ProgrammingProgrammable Flash RatesINC CO RING
INC ICW RINGCALL FORWARDMSG WAIT/VMBTN
BTN
*n %a%13 +%nMSG CBCK
DND DSS/BLFAUTO CBCK
UCD UNAVL
DSS/BLFDSS/BLFDSS/BLF
%+- 116 +#rT---ul2#18TRANSFER CORECALL COQUEUED CO
EXCLUSIVE
RINGRING
RINGHOLD
* lg +#k 110 I In+#nSYSTEM HOLDIN USE HOLDCAMP-ON BTNCALLBACK BTN
%+113*-+%- *mLINE QUEUE BTNDND BTNICM HOLD BTN
%+- %+- #Fir-i-lse 130Red LED Flash Rates
-
00
0102
03
04
05
06
07
08
09
IO
11
12
13
14
-Off
15Steady On
16
30 ipm Flash1760 ipm Flash
18
60 ipm Dbl Wink19240 ipm Flash20
240 ipm Flutter
21480 ipm Flash22
480 ipm Flutter23
15 ipm Flash24
120 ipm Flash25
120 ipm Flutter26
30 ipm Dbl Flash27
480 ipm Dbl Wink28
480 ipm Dbl Flash
Green LED Flash1Steady On
30 ipm Flash
60 ipm Flash60 ipm Dbl Wink
240 ipm Flash
240 ipm Flutter
480 ipm Flash
480 ipm Flutter
15 ipm Flash
120 ipm Flash120 ipm Flutter
30 ipm Dbl Flash
480 ipm Dbl Wink
480 ipm Dbl Flash
Table 2-6: Flash Rates
STARPLUS Triad-S System Programming Manual
Issue I- December 1998
Rates 
						

							 I2-40System Parameters Programming
Programmable Flash Rates
Incoming CO Line Ringing
Programming Steps_.,cT:.ze>;p:.>:q I>
1Press the INC CO RING flexible button (FLASH 07. button #I). The following message“?‘..-L..-
displays:
INC CO RING00-28
RED 480 IPM FLUTTER
zEnter a 2-digit value on the dial pad to correspond to one of the 29 available options.
Refer to the flash rate table.
3Press HOLD to save the entry. A confirmation tone is heard and the display updates.
Description
The Incoming CO Line Ringing flash rate is the rate at which an Incoming CO li.ne or Loop Button flashes.
This flash rate can be programmed to 29 different options identified in the flash rate table, which enables
the programmer to customize the key system configuration to desired flash rates. By default, the Incoming
CO Ringing flash rate is set for RED 480 ipm Flutter (08).
Incoming Intercom Ringing
Programming Steps
1Press the INC ICM RING flexible button (FLASH 07, button #2). The following message
displays:
INC ICM RING00-28
RED 120 IPM FLUTTER
2Enter a 2-digit value on the dial pad to correspond to one of the 29 available options.
Refer to flash rate table.
3Press HOLD to save the entry. A confirmation tone is heard and the display updates.
Description
_. :_-.,. ._i .!,T :I .:j i1 ,
The Incoming Intercom Ringing flash rate is the rate an Incoming DSS button flashes if you have a DSS
appearance for the calling station. This flash rate can be programmed to 
29 different options identified in
the flash rate table. This enables the programmer to customize the key system configuration to desired
flash rates. By default, the Incoming Intercom Ringing flash rate is set for RED 120 ipm Flutter (11).
issue I- December 7998STARPLUS Triad-S System Programming Manual 
						

							System Parameters Programming
Programmable Flash Rates
2-41
Call Forward Button
*-.-.
c-
Programming Steps,:-.:a-‘:..::~T~CYZ-1Press the CALL FORWARD BTN flexible button (FLASH 07. button #3). The following
message displays:
CALL FORWARD BTN00-28
RED STEADY ON
zEnter a 2-digit value on the dial pad to correspond to one of the 29 available options.
Refer to flash rate table.
3Press HOLD to save the entry. A confirmation tone is heard and the display updates.
Description
The Call Forward Button flash rate is the rate at which the Call Forward button flashes when any type of
forward mode is used. This flash rate can be programmed to 29 different options identified in the flash rate
table. This enables the programmer to customize the key system configuration to desired flash rates, By
default, Call Forward Button flash rate is set for a Red Steady On 
(01).
Message Wait / VM Button
Programming Steps
1Press the MSG WAIT/VM BTN flexible button (FLASH 07, button #4). The following
message displays:.
MSG WAIT / VM BTN00-28
RED STEADY ON
.
zEnter a 2-digit value on the dial pad to correspond to one of the 29 available options.
Refer to flash rate table.
3Press HOLD to save the entry. A confirmation tone is heard and the display updates..._r.--.:
c:.: .:i?,::.::..< Description_..”
The Message Wait/VM Button flash rate is the rate at which the Message Wait andVM button(s) flashes when
you receive a message/voice mail message. This flash rate can be programmed to 
29 different options
STARPLUS Triad-S System Programming Manualissue I - December 1998 
						

							2-42System Parameters Programming
Programmable Flash Rates
identified in the flash rate table. This enables the programmer to customize the key system configuration to
desired flash rates. By default, Message 
Wait/I’M Button flash rate is set for a Red Steady On (01).
The fixed message button should not be used US u Voice Mail button.
Message Callback - DSS / BLF
Programming Steps
1Press the MSG CBCK - DSS/BLF flexible button (FLASH 07, button #5). The following
message displays:
MSG CBCK DSS / BLF00-28
RED 120 IPM FLUTTER
4
2Enter a 2-digit value on the dial pad to correspond to one of the 29 available options.
Refer to flash rate table.
JPress HOLD to save the entry. A confirmation tone is heard and the display updates.
Description
The Message Callback DSS/BLF flash rate is the rate at which a DSS button of a station returning your
message flashes. This flash rate can be programmed to 
29 different options identified in the flash rate table.
This enables the programmer to customize the key system configuration to desired flash rates. By default,
Message Callback 
DSS/BLF flash rate is set for a Red 120 ipm Flutter (11).
Do Not Disturb - DSS / BLF
Programming Steps
1Press the DND - DSWBLF flexible button (FLASH 07, button #6). The following
message displays:
I
DND DSS / BLF00-28
RED 60 IPM DBL WINK
I
2Enter a 2-digit value on the dial pad to correspond to one of the 29 available options,
Refer to flash rate table.
Issue I- December 1998
STARPLUS Triad-S System Programming Manual 
						

							.:-.
System Parameters Programming
Programmable Flash Rates2-43
3Press HOLD to save the entry. A confirmation tone is heard and the display updates.
Description
c$$The Do Not Disturb DSS/BLF flash rate is the rate at which a DSS button of a station flashes when you are in
a Do Not Disturb mode. This flash rate can be programmed to 
29 different options identified in the flash rate
table. This enables the programmer to customize the key system configuration to desired flash rates. By
default, Do Not Disturb 
DSS/BLF flash rate is set for a Red 60 ipm Double Wink (04).Auto Callback 
- DSS / BLF
Programming Steps
IPress the AUTO CBCK - DSS/BLF flexible button (FLASH 07, button #7). The following
message displays:
AUTO CBCK DSS / BLF00-28
RED 120 IPM FLASH
2Enter a 2-digit value on the dial pad to correspond to one of the 29 available options.
Refer to flash rate table.
3Press HOLD to save the entry. A confirmation tone is heard and the display updates.
Description
The Auto Callback DSVBLF flash rate is the rate at which a DSS button of a station returning your call back
flashes. This flash rate can be programmed to 29 different options identified in the flash rate table. This
enables the programmer to customize the key system configuration to desired flash rates. By default, Auto
Callback 
DSS/BLF flash rate is set for a Red 120 ipm Flash (10).
UCD Available / Unavailable - DSS / BLF
Programming Steps
IPress the UCD UNAVL - DSS/BLF flexible button (FLASH 07, button #8). The following
message displays:
I
UCD UNAVL DSS / BLF00-28
RED 60 IPM DBL WINK
I
STARPLUS Triad-S System Programming Manualissue I- December 1998 
						

							2-44System Parameters Programming
Programmable Flash Rates
2Enter a 2-digit value on the dial pad to correspond to one of the 29 available options.
Refer to flash rate table.
3Press HOLD to save the entry. A confirmation tone is heard and the display updates.
Description
The UCD Available/Unavailable DSS/BLF flash rate is the rate at which a DSS appearance for a station in
ACD/UCD Unavailable mode flashes. This flash rate can be programmed to 29 different options identified in
the flash rate table. This enables the programmer to customize the key system configuration to desired
flash rates. By default, UCD Available/Unavailable 
DSS’BLF flash rate is set for a Red 60 ipm Double Wink
(04).
Transfer CO Ringing
Programming Steps
1Press the TRANSFER CO RING flexible button (FLASH 07, button #9). The following
message displays:
I
TRANSFER CO RING00-28
RED 120 IPM FLASH
I2Enter a 2-digit value on the dial pad to correspond to one of the 29 available options.
Refer to flash rate table.
3Press HOLD to save the entry. A confirmation tone is heard and the display updates.
Description
The Transfer CO Ringing flash rate is the rate at which a CO Line button or Loop button flashes when a call
is transferred to you. This flash rate can be programmed to 
29 different options identified in the flash rate
table, This enables the programmer to customize the key system configuration to desired flash rates. By
default, Transfer CO Ringing flash rate is set for a Red 120 ipm Flash (10).
Issue I - December 1998STARPLUS Triad-S System Programming Manual 
						

							System Parameters Programming
Programmable Flash Rates2-45
Recall CO Ringing
f
Programming Stepss:.%.;‘.: .L’.‘.-. c’‘zy1Press the RECALL CO RING flexible button (FLASH 07, button #lo). The following
message displays:
I
RECALL CO RING00-28RED 480 IPM FLUTTERI
2Enter a 2-digit value on the dial pad to correspond to one of the 29 available options.
Refer to flash rate table.
3Press HOLD to save the entry. A confirmation tone is heard and the display updates
Description
The Recall CO Ringing flash rate is the rate at which a CO Line button or Loop button flashes when a call
recalls to your station. This flash rate can be programmed to 
29 different options identified in the flash rate
table. This enables the programmer to customize the key system configuration to desired flash rates, By
default, Recall CO Ringing flash rate is set for a Red 480 ipm Flutter (08).
Queued CO Ringing
Programming Steps
1Press the QUEUED CO RING flexible button (FLASH 07, button #II). The following
message displays:
I
QUEUED CO RING00-28
GREEN 480 IPM FLUTTER
I
2Enter a 2-digit value on the dial pad to correspond to one of the 29 available options.
Refer to flash rate table.
3Press HOLD to save the entry. A confirmation tone is heard and the display updates.
Description
The Queued CO Ringing flash rate is the rate at which a CO Line button or Loop button flashes when a
queued line becomes available. This flash rate can be programmed to 29 different options identified in the
flash rate table. This enables the programmer to customize the key system configuration to desired flash
rates. By default, Queued CO Ringing flash rate is set for a Green 480 imp Flutter (22).
STARPLUS Triad-S System Programming Manualissue I- December 1998 
						

							;._-2-46
System Parameters Programming
Programmable Flash Rates
Exclusive Hold
Programming Steps
1Press the EXCLUSIVE HOLD flexible button (FLASH 07, button #12). The following
message displays:
EXCLUSIVE HOLD00-28
GREEN 120 IPM FLASH
zEnter a 2-digit value on the dial pad to correspond to one of the 29 available options.
Refer to flash rate table.
3Press HOLD to save the entry. A confirmation tone is heard and the display updates.
Description
The Exclusive Hold flash rate is the rate at which a CO Line button or Loop button flashes when a call is
placed on Exclusive Hold. This flash rate can be programmed to 29 different options identified in the flash
rate table. This enables the programmer to customize the key system configuration to desired flash rates.
By default, Exclusive Hold flash rate is set for a Green 120 ipm Flash (26).
System Hold
Programming Steps
1Press the SYSTEM HOLD flexible button (FLASH 07, button #13). The following
message displays:
SYSTEM HOLD00-28
RED 60 IPM DBL WINK
zEnter a 2-digit value on the dial pad to correspond to one of the 29 available options.
Refer to flash rate table.
3Press HOLD to save the entry. A confirmation tone is heard and the display updates.
Description
The System Hold flash rate is the rate at which a CO Line button or Loop button flashes when a call is
placed on System Hold. This flash rate can be programmed to 
29 different options identified in the flash
rate table. This enables the programmer to customize the key system configuration to desired flash rates.
By default, System Hold flash rate is set for a Red 
60 ipm Double Wink (04).
issue I- December 1998STARPLUS Triad-S System Programming Manual 
						

							.:. .
System Parameters Programming
Programmable Flash Rates2-47
In-Use Hold (I-Hold)
..,?.?%
cProgramming StepsL.... ~.,F.7 . . . -.-g:;1Press the IN USE HOLD flexible button (FLASH 07, button #14). The following message
displays:
I
IN-USE HOLD00-28
GREEN 60 IPM FLASH
\
.sEnter a 2-digit value on the dial pad to correspond to one of the 29 available options.
Refer to flash rate table.
3Press HOLD to save the entry. A confirmation tone is heard and the display updates.
Description
.’‘\
The In Use Hold (I-Hold) flash rate is the rate at which a CO Line button or Loop button flashes when a call
is placed on In Use Hold (I-Hold). This flash rate can be programmed to 
29 different options identified in the
flash rate table. This enables the programmer to customize the key system configuration to desired flash
rates. By default, In Use Hold (I-Hold) flash rate is set for a Green 
60 ipm Flash (17).
Camp-On Button
Programming Steps
1Press the CAMP-ON BTN flexible button (FLASH 07. button #15). The following
message displays:
I
CAMP ON BTN00-28
RED 120 IPM FLASHI
zEnter a 2-digit value on the dial pad to correspond to one of the 29 available options.
Refer to flash rate table.
3Press HOLD to save the entry. A confirmation tone is heard and the display updates.
Description
The Camp-On Button flash rate is the rate at which the Camp-On button flashes when you receive a Camp-
On. This hash rate can be programmed to 29 different options identified in the flash rate table, This enables
the programmer to customize the key system configuration to desired flash rates. By default, Camp-On
Button flash rate is set for a Red 120 ipm Flash (12).
STARPLUS Triad-S System Programming Manualissue I- December 1998 
						

							.:
I2-48
System Parameters Programming
Programmable Flash Rates
Callback Button
Programming Steps
IPress the CALL BACK BTN flexible button (FLASH 07, button #16). The following
message displays:
CALL BACK BTN00-28
RED 120 IPM FLASH
2Enter a 2-digit value on the dial pad to correspond to one of the 29 available options.
Refer to flash rate table.
3Press HOLD to save the entry. A confirmation tone is heard and the display updates.
Description
The Call Back Button flash rate is the rate at which the Call Back button flashes yhen a station at which you
left a call 
back request becomes available. This flash rate can be programmed to 29 different options
identified in the flash rate table. This enables the programmer to customize the key system configuration to
desired flash rates, By default, Call Back Button flash rate is set for a Red 120 ipm Flash (10).
Line Queue Button
Programming Steps
IPress the LINE QUEUE BTN flexible button (FLASH 07, button #17). The following
message displays:
LINE QUEUE BTN00-28
RED 480 IPM FLUTTER
zEnter a 2-digit value on the dial pad to correspond to one of the 29 available options.
Refer to flash rate table.
3Press HOLD to save the entry. A confirmation tone is heard and the display updates.
Description
The Line Queue Button flash rate is the rate at which the Line Queue button flashes after queueing onto a
busy line. This button flashes when the busy line becomes available. This flash rate can be programmed to
29 different options identified in the flash rate table which enables the programmer to customize the keyIssue I- December 1998
S JARPLUS Triad-S System Programming ManualI