Vodavi Starplus Triad S Description Manual

							Customer Database Programming
Database Upload/Download Routine1-25
3This displays the Send XMODEM screen on the PC monitor. Enter a path and file name
for the database file and press  and the desired file is uploaded to the system.
Send XMODEM
Please enter filename:
4A Confirmation tone is heard after the uploaded is complete and you are returned to the
ADM> prompt.
5Enter an M at the ADM> prompt and press .
adm>m
exiting admin...DATE: 
12/01/98TIME: 15:41:04
exiting maintenance utility...
sOn the PC, press  + . Press  to exit Procomm and return to the DOS
prompt.
7After the upload procedure is completed, the system MUST be reset for full activation
of the database programming to take effect.
STARPLUS Triad-S System Programming ManualIssue I- December 1998 
						

							Customer Database Programming
Database Upload/Download RoutineIssue I- December 1998
STARPLUS Triad-S System Programming Manual 
						

							:
Programming Steps
If the system is in the programming mode, continue using the program codes. If starting to program here,
enter the programming mode. Refer to Chapter 1: Customer Database Programming.
IPress FLASH and dial [Ol]. The following message displays:
SYSTEM TIMERS
ENTER BUTTON NUMBER
.
Description
This section describes the procedures and steps to program system timers in the System Timers
programming area. The buttons on the digital terminal are illustrated on the following page:
issue I- December 1998STARPLUS Triad-S System Programming Manual 
						

							System Parameters Programming
System TimersSYSTEMHOLD
RECALL
*llPRESET
FORWARD
+-
CONFlDlSATIMER
119MSG WAIT
REMINDER
*113AUTO CALL
BACK TIMER
4#-EXCL HOLD
ATTENDANT
RECALLRECALL
%l?x2iTl #izKEElCALL FWD
NO/ANSWERPAUSE TIMER
%- *mPAGINGCO RING
TIMEOUTDETECT
*- 4#nHOOK FLASHHOOK FLASH
DEBOUNCE
%+- *115REMINDERRELEASE GUARD
RINGTIMERTRANSFER
RECALL
$14CALL PARK
TIMER
*m
DISAISLTRECEIVER
9112SMDR CALL
QUALIFICATION
4kEiEKaINTER-DIGIT
TIMEOUT
%k-Program Flex
FeatureDefault
CodeButton
(after initialization)FLASH
011System Hold Recall060 seconds
2Exclusive Hold Recall180 seconds
3Attendant Recall Timer01 minutes
4Transfer Recall Timer045 seconds
5Preset Forward Timer10 seconds
6Call Forward No/Answer
015seconds
7Pause Timer2 seconds
8Call Park Recall Timer180 seconds
9Conf erence/DISA Timer10 minutes
10Paging Timeout Timer15 seconds
11CO Ring Detect Timer300 ms
12SLT DTMF Receiver Timer020 seconds
13MSG Wait Reminder Tone000 minutes
14SLT Hook Flash Timer
10 (1 second)
15SLT Hook Flash Debounce010 (.I seconds)
16SMDR Call Qualification Timer30 seconds
17Auto Call Back Timer
03 seconds (enabled)
18Reminder Ring Timer00 seconds (disabled)
19Release Guard Timer300 ms
20Inter-Digit Timeout5 seconds
Table 2-l: System Timers Defaults
Issue I- December 1998
STARPLUS Triad-S System Programming Manual 
						

							System Parameters Programming
System Timers2-3
System Hold Recall Timer
Programming StepsIPress the SYSTEM HOLD RECALL TIMER flexible button(FLASH 01, button 1). The
following message displays:
SYS HOLD RECALL000-300
060
2Enter a 3-digit timer value on the dial pad that corresponds to 000-300 seconds.
3Press HOLD to save the entry. A confirmation tone is heard and the display updates.
Description
This timer determines the time before a call placed on System Hold recalls the station placing the hold, If
unanswered by that station, the call recalls the attendant. By default, the System Hold Recall Timer is set for
60 seconds and is variable from 000-300 seconds. An entry of 000 disables the timer and there is no recall.
Exclusive Hold Recall Timer
Programming Steps
1Press the EXCLUSIVE HOLD RECALL TIMER flexible button (FLASH 01, button #2).The following message displays:
.
EXC HOLD RECALL000-300180
2Enter a 3-digit timer value on the dial pad that corresponds to 000-300 seconds,
3Press HOLD to save the entry. A confirmation tone is heard and the display updates.
Description
This timer determines the time before a call placed on Exclusive Hold recalls the station placing the Hold. If
unanswered by that station, the call recalls the attendant. By default, the Exclusive Hold Recall Timer is set
for 
180 seconds and is variable from 000-300 seconds. An entry of 000 disables the timer and there is no
recall.
STARPLUS Triad-S System Programming ManualIssue I- December 1998 
						

							2-4
‘-: :..-.
System Parameters Programming
System Timers
Attendant Recall Timer
Programming Steps
1Press the ATTENDANT RECALL TIMER flexible button (FLASH 01, button #3). The
following message displays:
ATND RECALL TIMER00-6001
6
zEnter a 2-digit timer value on the dial pad that corresponds to 00-60 minutes.
3Press HOLD to save the entry. A confirmation tone is heard and the display updates.
Description
This timer determines the time a recalling call rings at the attendant station(s) before the system releases
the line. When a CO Line recalls to the Attendant station and is still unanswered, the system releases the
line at the expiration of this timer and automatically places the line to an idle condition. By default, the
Attendant Recall Timer is set for 
1 minute and is variable from W-60 minutes. An entry of 00 causes the
Attendant(s) to ring until answered.
Transfer Recall Timer
Programming Steps
1Press the TRANSFER RECALL TIMER flexible button (FLASH 01, button #4). The
following message displays:
2Enter a 3-digit timer value on the dial pad that corresponds to 000-300 seconds.
TRA;;;ER RECALL000-300
3Press HOLD to save the entry. A confirmation tone is heard and the display updates.
Description
This timer determines the time a transferred call rings at the station receiving the transfer before it recalls
the station making the transfer. If unanswered by that station, the call recalls the attendant. By default, the
Transfer Recall Timer is set for 
45 seconds and is variable from 000-300 seconds. A 000 entry disables the
timer and there is no recall.
Issue I - December 1998STARPLUS Triad-S System Programming Manual 
						

							System Parameters Programming
System Timers
2-5
Preset Forward Timer
_.‘, Programming Steps
e
5. yi;....:_,. 1e.; :.;:’1Press the PRESET FORWARD TIMER flexible button (FLASH 01, button #5). The
following message displays:
I
PRESET FWD TIMER00-9910I
2Enter a 2-digit timer value on the dial pad that corresponds to 01-99 seconds.
3Press HOLD to save the entry. A confirmation tone is heard and the display updates.
Description
This timer determines the time an outside line rings before being forwarded to a predetermined station. This
entry works with Preset Forward station assignments in Station Programming. More than one station can be
forwarded to the same party.Initial incoming CO lines follow the Preset 
Call Forward Timer when
encountering a station in the Forward/No Answer mode.
This timer also governs the time the DISA call rings at a station before returning to intercom dial tone, if not
answered. By default, the Preset Forward Timer is set at 
10 seconds and is variable from 01-99 seconds. If
no preset forward destination is programmed, the feature is disabled.
Call Forward / No Answer Timer
Programming Steps
1Press the CALL FORWARD NO/ANSWER TIMER flexible button(FLASH 01, button #6).The following message displays:
I?i*
4”_ &.es-L3CALL FWD NO ANS000-600-I-i:.Y015
2Enter a 3-digit timer value on the dial pad that corresponds to 000-600 seconds.
3Press HOLD to save the entry. A confirmation tone is heard and the display updates.
STARPLUS Triad-S Sysfem Programming Manual
Issue I- December 7998 
						

							 ISystem Parameters Programming
System Timers
Description
This timer is used when a station in the system specifies that no answer calls be forwarded to another
station. The timer determines how long an intercom or transferred call rings before it is considered a no-
answer call. The call then forwards to the designated station for handling. By default, the Call Forward
No/Answer Timer is set for 15 seconds and is variable from 
000-600 seconds.
lnifiul incoming CO lines follow the Preset Call Forward Timer when
encountering a station in the Forward 
/ No Answer mode.
Pause Timer
Programing Steps
1Press the PAUSE TIMER flexible button (FLASH 01, button #7). The following message
displays:
+
PAUSE TIMERl-92
.
2Enter a l-digit timer value on the dial pad that corresponds to l-9 seconds.
3Press HOLD to save the entry. A confirmation tone is heard and the display updates.
Description
This timer determines the length of the pause when programmed for use with speed dialing and LCR Insert
Tables. By default, the Pause Timer is set at 2 seconds and is variable from l-9 seconds. There is no 0
entry. Use of this feature may afect Centrex transfers.Issue I- December 7998
STARPLUS Triad-S System Programming Manual 
						

							System Parameters Programming
System Timers
2-7
Call Park Recall Timer
in-., Programming Steps:: ”&ITIPress the CALL PARK RECALL TIMER flexible button (FLASH 01, button #8). The
following message displays:
CALL PARK TIMER000-600180
2Enter a 3-digit timer value on the dial pad that corresponds to 001-600 seconds.
3Press HOLD to save the entry. A confirmation tone is heard and the display updates.
Description
This timer determines the time before a call placed in a call park location recalls the station placing the call
in park. If unanswered by that station, the call recalls the attendant. By default, the Call Park Recall Timer is
set at 
180 seconds and is variable from 000-600 seconds. A 000 entry disables the timer and there is no
recall.Conference 
/ DISA Timer
Programming Steps
1Press the CONFERENCEIDISA TIMER flexible button (FLASH 01, button #9). The
following message displays:
CONFERENCE TIMER00-9910
..
2Enter a 2-digit timer value on the dial pad that corresponds to 01-99 minutes.
3Press HOLD to save the entry. A confirmation tone is heard and the display updates.
STARPLUS Triad-S System Programming Manualissue I - December 1998 
						

							2-8System Parameters Programming
System Timers
Description
This timer determines the time an unsupervised conference can continue after the initiator of the
conference has exited. By default, the 
Conference/DISA Timer is set at 10 minutes and is variable from Ol-
99 minutes. A 00 entry disables the timer and no automatic disconnect occurs.The Conference Timer also allows the system 
administrator to control the
time a 
DISA caller is allowed after establishing o Trunk-to- Trunk call. At
the expiration of the Conference Timer, 
u tone is presented to both DISAparties, then one minute later the system automatically releases both
trunks. 
The Conference Timer does not affect or control a DISA-to-
Station call.
Paging Time-out Timer
Programming Steps
1Press the PAGING TIMEOUT TIMER flexible button (FLASH 01, button #lo). The
following message displays:
I
PAGING TIMEOUT00-6015I
zEnter a 2-digit timer value on the dial pad that corresponds to 01-60 seconds.
3Press HOLD to save the entry. A confirmation tone is heard and the display updates.
Description
This timer determines the maximum length of a page announcement (internal, external or all call). The
system automatically disconnects the page at the end of this time unless the person making the page has
already hung up. By default, the Paging Time-out Timer is set at 15 seconds and is variable from 
01-60
seconds. A 00 entry disables the timer and pages are not limited in length. This 
will a&et use of the Meet
Me Page feature.
issue I- December 1998STARPLUS Triad-S System Programming Manual